keyless entry NISSAN TEANA 2003 Owner's Guide

BL-72
INTELLIGENT KEY SYSTEM

Hazard Reminder Function
The hazard lamps are flashed when the door lock is locked or unlocked by remote controller button.
When ignition switch ON or any door is opened, key reminder function is not operate.
List of Operation Related Parts
Parts marked with × are the parts related to operation.
ENGINE START FUNCTION
Operation Description

When ignition knob is pressed, Intelligent Key unit sends request signal from inside key antenna, key-ID
verification is performed with Intelligent Key using two-way communication, and if verification is success-
ful, an ignition rotation prohibition latch release signal is sent to steering lock unit. Steering lock unit
releases ignition knob rotation prohibition latch. (Ignition knob can now be turned.)

When it becomes possible to rotate the ignition knob, “KEY” warning lamp in combination meter lights up
green to notify driver that ignition knob can be turned.
NOTE:
When it becomes impossible to rotate the ignition knob, “KEY” warning lamp in combination meter lights
up red.

When key-ID verification is successful, Intelligent Key unit uses CAN communication to send engine start
permission signal to BCM.

When BCM receives engine start permission signal, it uses CAN communication to sent starter request
signal to IPDM E/R so that the engine will start when ignition knob is rotated to START position.
Operation Range
Engine can be started when Intelligent Key is in the vehicle. However, sometimes engine might not start when
Intelligent Key is on instrument panel, rear parcel shelf, trunk room or in glove box.
Unlock
Remove mechanical key from ignition key cylinder (key switch: OFF)

Ignition knob is not press (ignition knob switch: OFF)
Trunk open

Remove mechanical key from ignition key cylinder (key switch: OFF)

Ignition knob is not press (ignition knob switch: OFF)

When trunk button pressed more than 0.5 seconds Remote controller button operation Operating condition
Vehicle operation Hazard lamp
Door unlocking operation Twice
Door locking operation Once
Remote keyless entry functions
Intelligent Key
Key switch
Ignition knob switch
Door unlock sensor
Door switch
Trunk room lamp switch
Door lock actuator
Trunk lid opener actuator
Intelligent Key unit
CAN communication system
BCM
Combination meter
Hazard warning lamp
Door lock function by the remote control button××××× × ×××
Trunk open function by the remote control button××× × ××××
Hazard reminder function (Door lock)×××××

BL-96
INTELLIGENT KEY SYSTEM

Trouble Diagnosis Symptom ChartBIS000XC
ALL FUNCTIONS OF THE INTELLIGENT KEY ARE NOT OPERATING
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Intelligent key function (I-KEY FUNCTION) is ON when setting on CONSULT-II. Refer to BL-94, "WORK
SUPPORT" .

Mechanical key is not inserted into ignition knob.

Ignition knob is not depressed.

All doors are closed.
REMOTE KEYLESS ENTRY FUNCTION MALFUNCTION
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Intelligent key function (I-KEY FUNCTION) is ON when setting on CONSULT-II. Refer to BL-94, "WORK
SUPPORT" .

Mechanical key is not inserted into ignition knob.

Ignition knob is not depressed.

All doors are closed.
Symptom Diagnoses service procedure Reference page
All Intelligent Key function does not operate.1.Use CONSULT-II to check if the Intelligent Key has
been registeredBL-94
2.Check Intelligent Key unit power supply and ground
circuitBL-100
3. Check CAN communicationBL-100
4. Replace Intelligent Key unitBL-117
Symptom Diagnoses service procedure Reference page
Either one of the remote keyless entry function
do not operate.Replace Intelligent Key unitBL-117

LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
DTC B2087 [SHORT TO GROUND] ..................... 116
DTC B2088 [SHORT TO BATTERY] ..................... 118
Removal and Installation of Height Sensor .......... 120
REMOVAL ......................................................... 120
INSTALLATION ................................................. 120
HEADLAMP AIMING CONTROL (MANUAL) ........ 121
Schematic ............................................................ 121
Wiring Diagram — H/AIM — ................................ 122
Removal and Installation ...................................... 125
REMOVAL ......................................................... 125
INSTALLATION ................................................. 125
Switch Circuit Inspection ...................................... 125
FRONT FOG LAMP ................................................ 126
Component Parts and Harness Connector Location . 126
System Description .............................................. 126
OUTLINE ........................................................... 126
COMBINATION SWITCH READING FUNCTION . 127
EXTERIOR LAMP BATTERY SAVER CONTROL . 127
CAN Communication System Description ............ 127
CAN Communication Unit .................................... 127
Schematic ............................................................ 128
Wiring Diagram — F/FOG — ............................... 129
Terminals and Reference Values for BCM ........... 132
Terminals and Reference Values for IPDM E/R ... 133
How to Perform Trouble Diagnosis ...................... 133
Preliminary Check ................................................ 133
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. 133
CONSULT-II Functions (BCM) ............................. 134
CONSULT-II Functions (IPDM E/R) ..................... 134
Front Fog Lamps Do Not Illuminate (Both Sides) . 135
Front Fog Lamp Does Not Illuminate (One Side) . 137
Front Fog Lamp Indicator Lamp Does Not Illuminate . 138
Front Fog Lamps Does Not Go OFF (Both Sides) . 139
Aiming Adjustment ............................................... 140
Bulb Replacement ................................................ 141
Removal and Installation ...................................... 141
REMOVAL ......................................................... 141
INSTALLATION ................................................. 141
REAR FOG LAMP .................................................. 142
Component Parts and Harness Connector Location . 142
System Description .............................................. 142
OUTLINE ........................................................... 142
COMBINATION SWITCH READING FUNCTION . 143
EXTERIOR LAMP BATTERY SAVER CONTROL . 143
CAN Communication System Description ............ 143
CAN Communication Unit .................................... 143
Wiring Diagram — R/FOG — ............................... 144
Terminals and Reference Value for BCM ............. 146
How to Proceed With Trouble Diagnosis .............. 147
Preliminary Check ................................................ 147
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. 147
CONSULT-II Function (BCM) ............................... 148
Rear Fog Lamp Does Not Illuminate .................... 148
Rear Fog Lamp Indicator Lamp Does Not Illuminate . 150
Rear Fog Lamp Does Not Go OFF ...................... 151
Bulb Replacement ................................................ 151
Removal and Installation ...................................... 151TURN SIGNAL AND HAZARD WARNING LAMPS .152
Component Parts and Harness Connector Location .152
System Description ...............................................152
OUTLINE ...........................................................152
TURN SIGNAL OPERATION ............................153
HAZARD LAMP OPERATION ...........................153
INTERLOCKED HAZARD LAMP OPERATION
WITH REMOTE KEYLESS ENTRY SYSTEM ...154
INTERLOCKED HAZARD LAMP OPERATION
WITH INTELLIGENT KEY SYSTEM .................154
COMBINATION SWITCH READING FUNCTION .154
CAN Communication System Description ............154
CAN Communication Unit .....................................154
Schematic .............................................................155
Wiring Diagram — TURN — .................................156
Terminals and Reference Values for BCM ............159
How to Perform Trouble Diagnoses .....................160
Preliminary Check ................................................161
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................161
CONSULT-II Functions (BCM) ..............................162
CONSULT-II BASIC OPERATION .....................162
DATA MONITOR ...............................................162
ACTIVE TEST ...................................................162
Turn Signal Lamp RH Does Not Illuminate ...........163
Turn Signal Lamp LH Does Not Illuminate ...........167
Turn Signal Lamps Do Not Operate But Hazard
Warning Lamp Operate ........................................170
Hazard Warning Lamp Do Not Operate But Turn Sig-
nal Lamp Operate .................................................171
Turn Signal Indicator Lamp Does Not Illuminate ..173
Turn Signal Lamps Do Not Go OFF .....................173
Bulb Replacement ................................................175
SIDE TURN SIGNAL LAMP ..............................175
FRONT TURN SIGNAL LAMP ..........................175
REAR TURN SIGNAL LAMP ............................175
Removal and Installation ......................................175
SIDE TURN SIGNAL LAMP ..............................175
FRONT TURN SIGNAL LAMP ..........................175
REAR TURN SIGNAL LAMP ............................175
LIGHTING AND TURN SIGNAL SWITCH ..............176
Removal and Installation ......................................176
REMOVAL .........................................................176
INSTALLATION .................................................176
Switch Circuit Inspection ......................................176
HAZARD SWITCH ..................................................177
Removal and Installation ......................................177
REMOVAL .........................................................177
INSTALLATION .................................................177
COMBINATION SWITCH ........................................178
Wiring Diagram — COMB SW — .........................178
Terminals and Reference Values for BCM ............179
Combination Switch Reading Function .................183
CONSULT-II Functions (BCM) ..............................183
CONSULT-II BASIC OPERATION .....................184
DATA MONITOR ...............................................184
Combination Switch Inspection ............................185
Removal and Installation ......................................189
STOP LAMP ............................................................190

LT-154
TURN SIGNAL AND HAZARD WARNING LAMPS


through grounds M71 and M72.
And BCM supplies power

through BCM terminal 46

to front combination lamp RH terminal 8

to side turn signal lamp RH terminal 1 and

to rear combination lamp RH terminal 1,

through BCM terminal 45

to front combination lamp LH terminal 8

to side turn signal lamp LH terminal 1 and

to rear combination lamp LH terminal 1.
Ground is supplied

to front combination lamp RH and LH terminals 4

to side turn signal lamp RH and LH terminals 2

through grounds E1 and E31,

to rear combination lamp RH and LH terminals 2

through grounds M71 and M72 (with rear view camera)

through grounds B16 and B17(without rear view camera).
Unified meter and A/C amp. receives the turn indicator signal (RH and LH) through CAN communication, then
makes turn (RH and LH) indicator start flashing operation interlocked with the buzzer sounds in combination
meter.
With power and ground supplied, BCM controls the blinking of the hazard warning lamp.
INTERLOCKED HAZARD LAMP OPERATION WITH REMOTE KEYLESS ENTRY SYSTEM
BCM receives the keyfob signal (door lock/unlock signal) from remote keyless entry receiver, then BCM con-
trols hazard lamps.
Refer to BL-46, "
REMOTE KEYLESS ENTRY SYSTEM" .
INTERLOCKED HAZARD LAMP OPERATION WITH INTELLIGENT KEY SYSTEM
BCM receives the door lock/unlock signal from Intelligent Key unit through CAN communication, then BCM
controls hazard lamps.
Refer to BL-68, "
INTELLIGENT KEY SYSTEM" .
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
CAN Communication System DescriptionBKS001PO
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001PP
Refer to LAN-49, "CAN System Specification Chart" .

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-197
C
D
E
F
G
H
I
J
L
MA
B
LT


to unified meter and A/C amp. terminal 21.
With the ignition switch in the ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8,

through 10A fuse [No. 12, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 22.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52

to combination meter terminals 10, 11 and 12, and

to unified meter and A/C amp. terminals 29 and 30

through grounds M71 and M72,

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
PARKING, LICENCE PLATE AND TAIL LAMPS OPERATION
When the lighting switch is in 1ST position, BCM detects the LIGHTING SWITCH 1ST POSITION (ON) by
BCM combination switch reading function. And then, BCM sends position light request signal (ON) through
CAN communication.
When receiving position light request signal (ON), IPDM E/R turns ON tail lamp relay in IPDM E/R. And then,
parking, license plate and tail lamps go ON. IPDM E/R supplies power

through IPDM E/R terminal 22

to front combination lamp RH and LH terminals 7

to license plate lamp RH and LH terminals 1 and

to rear combination lamp RH and LH terminals 3.
Ground is supplied at all times

to front combination lamp RH and LH terminals 4

through grounds E1 and E31,

to license plate lamp RH and LH terminals 2

through grounds B214 and B217,

to rear combination lamp RH and LH terminals 2

through grounds M71 and M72 (with rear view camera)

through grounds B16 and B17 (without rear view camera).
With power and ground supplied, the parking, license plate and tail lamps illuminate.
Unified meter and A/C amp. receives position light request signal (ON) through CAN communication, make tail
lamp indicator go ON in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When any of the 1ST/2ND position with exterior lamp ON, the ignition switch is turned to OFF. The driver's
door is opened to get out of the car and then closed, BCM turns OFF exterior lamp with door lock operation of
the remote keyless entry system or Intelligent Key system in order to prevent battery from running by forget-
ting about turning OFF the exterior lamp.
This setting can be changed by CONSULT-II. Refer to LT- 1 9 , "
WORK SUPPORT" .

LT-234
INTERIOR ROOM LAMP

Display Item List
NOTE:
1. Vehicle with Intelligent Key system displays this item.
2. Vehicle with remote keyless entry system displays this item.
ACTIVE TEST
Operation Procedure
1. Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching “OFF” deactivates the operation.
Display Item List
WORK SUPPORT (BATTERY SAVER)
Operation procedure
1. Select “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2. Select “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3. Select “ROOM LAMP BAT SAV SET” on “SELECT WORK ITEM” screen.
4. Touch “START”.
5. Touch “MODE1” or “MODE2” (ROOM LAMP TIMER SET)
6. Touch “CHANGE SETT”.
7. The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
8. Touch “END”.
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL “ON/OFF”Displays “Door open (ON)/Door closed (OFF) ” status, determined from rear door switch LH
signal.
LOCK STATUS “ON/OFF”Displays “Door unlocked (ON) /Door locked (OFF) status, determined from door unlock sen-
sor signal.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from central door lock
switch LOCK signal.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from central door lock switch UNLOCK
signal.
I − KEY LOCK
NOTE 1“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
I − KEY UNLOCK
NOTE 1“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
KEYLESS LOCK
NOTE2“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK
NOTE2“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
CONSULT-II screen
displayTest item Description
INT LAMPMap lamp, personal lamp and
ignition key hole illumination
operationMap lamp, personal lamp and ignition keyhole illumination is operated by
switching operation ON-OFF when map lamp switch and personal switch is in
DOOR position.

INTERIOR ROOM LAMP
LT-235
C
D
E
F
G
H
I
J
L
MA
B
LT

Display Item List
DATA MONITOR (BATTERY SAVER)
Operation Procedure
1. Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3. Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4. When “ALL SIGNALS” is selected, all the items will be monitored. When “SELECTION FROM MENU” is
selected, touch individual items to be monitored.
5. Touch “START”.
6. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
Display Item List
NOTE:
1. Vehicle with Intelligent Key system displays this item.
2. Vehicle with remote keyless entry system displays this item.Item Description CONSULT-II
ROOM LAMP TIMER SET Interior room lamp battery saver timer setting can be changed.MODE 1: 30 min.
MODE 2: 60 min.
ROOM LAMP BAT SAV SETInterior room lamp battery saver control mode can be changed in this mode.
Select interior room lamp battery saver control mode between ON and OFF.ON/OFF
ALL SIGNALS Monitors all the items.
SELECTION FROM MENU Selects items and monitor them.
Monitor item Contents
IGN ON SW “ON/OFF”Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch sig-
nal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR “ON/OFF”Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door
switch signal.
DOOR SW - RR “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from rear door switch RH
signal.
DOOR SW - RL “ON/OFF”Displays “Door open (ON)/Door closed (OFF) ” status, determined from rear door switch LH
signal.
LOCK STATUS “ON/OFF”Displays “Door unlocked (ON)/Door locked (OFF) status, determined from door unlock sen-
sor signal.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from central door lock
switch LOCK signal.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from central door lock switch UNLOCK
signal.
I − KEY LOCK
NOTE 1“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
I − KEY UNLOCK
NOTE 1“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.
KEYLESS LOCK
NOTE2“ON/OFF” Displays “Locked (ON)/other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK
NOTE2“ON/OFF” Displays “Unlocked (ON)/other (OFF)” status, determined from unlock signal.

PG-64
HARNESS

FRO2B1 EC Heated Oxygen Sensor 1 Heater Bank 1
FRO2B2 EC Heated Oxygen Sensor 1 Heater Bank 2
FTS CVT CVT Fluid Temperature Sensor Circuit
H/AIM LT Headlamp Aiming Control System
H/LAMP LT Headlamp
HLC WW Headlamp Washer
HORN WW Horn
HO2S1 EC Heated Oxygen Sensor 1
HSEAT SE Heated Seat
I/KEY BL Intelligent Key System
IATSEN EC Intake Air Temperature Sensor
IGNSYS EC Ignition System
ILL LT Illumination
INF/D AV Vehicle Information and Integrated Switch System
INJECT EC Injector
INT/L LT Vanity Mirror Lamp
IVC EC Intake Valve Timing Control Solenoid Valve
IVCB1 EC Intake Valve Timing Control Solenoid Valve Bank 1
IVCB2 EC Intake Valve Timing Control Solenoid Valve Bank 2
KEYLES BL Remote Keyless Entry System
KS EC Knock Sensor
L/USSV CVT Lock-Up Select Solenoid Valve
LPSV AT Line Pressure Solenoid Valve
LPSV CVT Line Pressure Solenoid Valve
M/SEAT SE Air Massage Seat
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp. and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Power Door Mirror
MMSW CVT Manual Mode Switch
NATS BL Nissan Anti-Theft System
NONDTC AT Non-Detective Items
NONDTC CVT Non-Detective Items
O2S1B1 EC Heated Oxygen Sensor 1 Bank 1
O2S1B2 EC Heated Oxygen Sensor 1 Bank 2
OVRCSV AT Overrun Clutch Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHSB1 EC Camshaft Position Sensor (PHASE) (Bank1)
PHSB2 EC Camshaft Position Sensor (PHASE) (Bank2)
PNP/SW CVT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS) Code Section Wiring Diagram Name