Connector NISSAN TEANA 2003 Service Manual

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-171
C
D
E
F
G
H
I
J
L
MA
B
LT

Hazard Warning Lamp Do Not Operate But Turn Signal Lamp OperateBKS001PX
1. CHECK CIRCUIT BETWEEN HAZARD SWITCH AND BCM
1. Select “BCM” on CONSULT-II, and select “FLASHER” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “HAZARD SW” turns ON-OFF according to haz-
ard switch operation.
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NG >> GO TO 2.
2. CHECK BCM OUTPUT VOLTAGE
Check voltage between BCM harness connector and ground.
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NG >> GO TO 3.
3. CHECK HAZARD SWITCH
1. Turn ignition switch OFF.
2. Remove hazard switch.
3. Check continuity between hazard switch terminals.
OK or NG
OK >> GO TO 4.
NG >> Replace hazard switch. Refer to LT- 1 7 7 , "
Removal and
Installation" . When hazard switch is in the
ON position : HAZARD SW ON
PKIA6865E
Terminal
ConditionVoltage
(Approx.) (+)
(−)
Connector Terminal
M3 29 GroundHazard switch is ON. 0 V
Hazard switch is OFF. Battery Voltage
PKID0301E
Hazard switch
Condition Continuity
Te r m i n a l s
12Hazard switch is ON. Yes
Hazard switch is OFF. No
PKID0281E

LT-172
TURN SIGNAL AND HAZARD WARNING LAMPS

4. CHECK CIRCUIT BETWEEN HAZARD SWITCH AND BCM
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector (A) and haz-
ard switch harness connector (B).
3. Check continuity between BCM connector and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK CIRCUIT BETWEEN HAZARD SWITCH AND GROUND
Check continuity between hazard switch harness connector and
ground.
OK or NG
OK >> Repair connector for connection bend and loose fit.
NG >> Repair harness or connector.
AB
Continuity
Connector Terminal Connector Terminal
M3 29 M39 2 Yes
A
GroundContinuity
Connector Terminal
M3 29 No
PKID0282E
Hazard switch
connectorTerminal
GroundContinuity
M39 1 No
PKID0283E

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-175
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001PZ
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer to LT- 1 7 5 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 5 , "Bulb Replacement" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS001Q2
SIDE TURN SIGNAL LAMP
Removal
1. While pressing side turn signal lamp to direction A (vehicle
front), pull it to direction B and then remove it.
2. Disconnect side turn signal lamp connector.
NOTE:
Support side turn signal lamp harness with tape so that it won't
fall into the front fender.
CAUTION:
Install the side turn signal lamp housing with the bead fac-
ing up.
Installation
Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 6 , "Removal and Installation" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . Side turn signal lamp : 12V - 5W
PKIA0015E
SKIA7249E

HAZARD SWITCH
LT-177
C
D
E
F
G
H
I
J
L
MA
B
LT

HAZARD SWITCHPFP:25290
Removal and InstallationBKS001Q6
REMOVAL
1. Remove cluster lid D. Refer to IP-10, "INSTRUMENT PANEL
ASSEMBLY" .
2. Disconnect connector.
3. Remove screw and remove hazard switch integral with center
ventilator grille from cluster lid D.
4. Pawl on rearward and remove hazard switch.
INSTALLATION
Installation is the reverse order of removal.
PKIB7984E

COMBINATION SWITCH
LT-187
C
D
E
F
G
H
I
J
L
MA
B
LT

3. CHECK HARNESS BETWEEN COMBINATION SWITCH AND BCM
1. Turn ignition switch OFF.
2. Disconnect BCM connector and combination switch connector.
3. Check for continuity between BCM harness connector (A) of the suspect system and the corresponding
combination switch connector (B).
4. Check for continuity between each of BCM harness connector in suspect malfunctioning system and
ground.
OK or NG
OK >> Check BCM input/output signal of malfunctioning input/output.

Input: GO TO 4.

Output: GO TO 5.
NG >> Repair harness or connector.
Sus-
pect
systemAB
Continuity
Connector Terminal Connector Terminal
1
M3Input 1 6
M276
Ye s Output 1 36 1
2Input 2 5 7
Output 2 35 2
3Input 3 4 10
Output 3 34 3
4Input 4 3 9
Output 4 33 4
5Input 5 2 8
Output 5 32 5
Suspect
systemBCM
connectorTerminal
GroundContinuity
1
M3Input 1 6
No Output 1 36
2Input 2 5
Output 2 35
3Input 3 4
Output 3 34
4Input 4 3
Output 4 33
5Input 5 2
Output 5 32
PKID0105E
PKIA7506E

LT-188
COMBINATION SWITCH

4. CHECK BCM INPUT SIGNAL
1. Connect BCM connector and combination switch connector.
2. Turn ignition switch ON.
3. Lighting switch and wiper switch are turned OFF.
4. Set wiper intermittent dial position 4.
5. Check BCM input terminal voltage waveform of suspect mal-
functioning system.
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installation of BCM" .
NG >> Open circuit in combination switch, GO TO 6.
5. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector and combination switch connector.
2. Turn ignition switch ON.
3. Lighting switch and wiper switch are turned OFF.
4. Set wiper intermittent dial position 4.
5. Check BCM output terminal voltage waveform of suspect mal-
functioning system.
OK or NG
OK >> Open circuit in combination switch, GO TO 6.
NG >> Replace BCM. Refer to BCS-16, "
Removal and Installation of BCM" .
Suspect
systemTerminal
Reference value (+)
(-)
BCM
connectorTerminal
1
M36
GroundRefer to LT-179, "
Terminals and
Reference Values for BCM" . 25
34
43
52PKID0106E
Suspect
systemTerminal
Reference value (+)
(-)
BCM
connectorTerminal
1
M336
Ground
Approx. 7.0 - 7.5V 235
334
433
532
PKID0107E
PKIB4960J

LT-192
STOP LAMP

Bulb ReplacementBKS001QD
HIGH-MOUNTED STOP LAMP
Replacement integral with high-mounted stop lamp. Refer to LT- 1 9 2 , "Removal and Installation" .
STOP LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040N
HIGH-MOUNTED STOP LAMP
Removal
1. Remove rear parcel shelf finisher. Refer to EI-43, "Removal and Installation" .
2. Disconnect high-mounted stop lamp connector.
3. Remove high-mounted stop lamp mounting screws and remove
high-mounted stop lamp from rear parcel shelf finisher.
Installation
Note the following, and installation is the reverse order of removal.
STOP LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . High-mounted stop lamp : LED
SKIA6346E
High-mounted stop lamp
mounting screws: 3.15 N·m (0.32 kg-m, 28in-lb)

LT-196
PARKING, LICENSE PLATE AND TAIL LAMPS

PARKING, LICENSE PLATE AND TAIL LAMPSPFP:26550
Component Parts and Harness Connector LocationBKS001QJ
System DescriptionBKS001QK

BCM (Body Control Module) controls parking, license plate and tail lamps operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates parking, license plate and tail
lamps according to CAN communication signals from BCM.

Unified meter and A/C amp. operates tail lamp indicator according to CAN communication signals from
BCM.
OUTLINE
Power is supplied at all times

to ignition relay (located in IPDM E/R), from battery direct,

through 15A fuse (No. 71, located in IPDM E/R)

to tail lamp relay (located in IPDM E/R) and

to CPU (central processing unit) in IPDM E/R,

through 15A fuse (No. 78, located in IPDM E/R)

to CPU in IPDM E/R,

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7,

through 10A fuse [No.19, located in fuse block (J/B)]
PKID0048E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-207
C
D
E
F
G
H
I
J
L
MA
B
LT

2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
CONSULT-II Functions (BCM)BKS001QT
Refer to LT- 1 8 , "CONSULT-II Functions (BCM)" .
CONSULT-II Functions (IPDM E/R)BKS001QU
Refer to LT- 2 0 , "CONSULT-II Functions (IPDM E/R)" .
Terminals Ignition switch position
(+)
(−)OFFACCON
BCM
connectorTerminal
M311
GroundApprox. 0 VBattery
voltageBattery
voltage
38 Approx. 0 V Approx. 0 VBattery
voltage
M442Battery
voltageBattery
voltageBattery
voltage
55 Battery
voltageBattery
voltageBattery
voltage
PKIA5204E
BCM connector Terminal
GroundContinuity
M4 52 Yes
PKIA6256E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-209
C
D
E
F
G
H
I
J
L
MA
B
LT

4. CHECK CIRCUIT BETWEEN IPDM E/R AND PARKING, LICENSE PLATE, TAIL LAMPS
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector, front combination lamp RH and LH connectors, rear combination lamp
RH and LH connectors and licence plate lamp RH and LH connectors.
3. Check continuity between IPDM E/R harness connector and
front combination lamp harness connector.
4. Check continuity between IPDM E/R harness connector (A) and
rear combination lamp harness connector (B).
5. Check continuity between IPDM E/R harness connector (A) and
license plate lamp harness connector (B).
6. Check continuity between IPDM E/R harness connector (A) and
ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
IPDM E/R
connectorTerminalHeadlamp
typeFront combination
lamp connectorTerminal Continuity
E7 22XenonRH E15
7 Yes LH E29
HalogenRH E47
LH E46
PKIA6295E
AB
Continuity
Connector Terminal Connector Terminal
E7 22RH B24
3Yes
LH B33
PKID0284E
AB
Continuity
Connector Terminal Connector Terminal
E7 22RH T3
1Yes
LH T4
A
GroundContinuity
Connector Terminal
E7 22 No
PKID0108E