169 NISSAN TEANA 2003 Service Manual

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-169
D
E
F
G
H
I
J
K
L
MA
B
AT

TCWM0521E

REPAIR FOR COMPONENT PARTS
AT-325
D
E
F
G
H
I
J
K
L
MA
B
AT

7. Press out reduction pinion gear bearing inner race from reduc-
tion pinion gear.
8. Remove reduction pinion gear bearing outer race from transaxle
case.
INSPECTION
Output Shaft, Idler Gear and Reduction Pinion Gear
Check for wear, damage or crack. Replace if necessary.
Bearings

Make sure bearings roll freely and are free from noise, cracks,
pitting or wear. Replace if necessary.
CAUTION:
When replacing taper roller bearing, replace outer and inner
race as a set.
Seal Ring Clearance

Install new seal rings to output shaft.

Measure clearance between seal ring and ring groove of output
shaft.

If not within allowable limit, replace output shaft.

Install new seal rings to bearing retainer.

Measure clearance between seal ring and ring groove of bear-
ing retainer.

If not within allowable limit, replace bearing retainer.
SAT169F
SAT319K
SPD715
Standard clearance and allowable limit:
Refer to AT- 3 6 8 , "
Output Shaft" .
Standard clearance and allowable limit:
Refer to AT- 3 6 8 , "
Bearing Retainer" .
SAT171F

TROUBLE DIAGNOSIS
ATC-81
C
D
E
F
G
H
I
K
L
MA
B
AT C

7. CHECK VOLTAGE FOR UNIFIED METER AND A/C AMP. (COMPRESSOR ON SIGNAL)
1. Reconnect BCM connector and unified meter and A/C amp.
connector.
2. Turn ignition switch ON.
3. Check voltage between unified meter and A/C amp. harness
connector M45 terminal 42 and ground.
OK or NG
OK >> GO TO 8.
NG-1 >> If the voltage is approx. 5 V when A/C switch is ON: Replace unified meter and A/C amp.
NG-2 >> If the voltage is approx. 0 V when A/C switch is OFF: Replace BCM.
8. CHECK REFRIGERANT PRESSURE SENSOR
WITH CONSULT-II
1. Start the engine.
2. Check voltage of refrigerant pressure sensor. Refer to EC-90,
"CONSULT-II Reference Value in Data Monitor Mode" (QR
engine) or EC-434, "
CONSULT-II Reference Value in Data Mon-
itor Mode" (VQ engine).
WITHOUT CONSULT-II
1. Start the engine.
2. Check voltage between ECM harness connector F101 terminal
70 and ground.
OK or NG
OK >>
WITH CONSULT-II: GO TO 9.

WITHOUT CONSULT-II: GO TO 10.
NG >> Refer to EC-339, "
REFRIGERANT PRESSURE SENSOR" (QR engine) or EC-748, "REFRIGER-
ANT PRESSURE SENSOR" (VQ engine).
Te r m i n a l s
Condition Voltage (+)
(-) Unified meter
and A/C amp.
connectorTerminal
No.
M45 42 GroundA/C switch: ON
(Blower motor oper-
ates.)Approx. 0 V
OFF switch: ON (A/C
System: OFF)Approx. 5 V
RJIA2007E
Terminals
Condition Voltage (+)
(-)
ECM con-
nectorTerminal No.
F10169 (QR engine)
GroundA/C switch: ON
(Blower motor
operates.)Approx. 1.0 - 4.0 V
70 (VQ engine)
SJIA1723E

CVT-4 On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ...............................143
WITH CONSULT-II ............................................143
Diagnostic Procedure ...........................................144
DTC P1726 ELECTRIC THROTTLE CONTROL
SYSTEM ..................................................................145
Description ............................................................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ...............................145
WITH CONSULT-II ............................................145
Diagnostic Procedure ...........................................146
DTC P1740 LOCK-UP SELECT SOLENOID VALVE
CIRCUIT ..................................................................147
Description ............................................................147
CONSULT-II Reference Value ..............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ...............................147
WITH CONSULT-II ............................................147
Wiring Diagram — CVT — L/USSV ......................148
Diagnostic Procedure ...........................................149
Component Inspection ..........................................151
LOCK-UP SELECT SOLENOID VALVE ............151
DTC P1745 LINE PRESSURE CONTROL .............152
Description ............................................................152
On Board Diagnosis Logic ....................................152
Possible Cause .....................................................152
DTC Confirmation Procedure ...............................152
WITH CONSULT-II ............................................152
Diagnostic Procedure ...........................................152
DTC P1777 STEP MOTOR - CIRCUIT ...................153
Description ............................................................153
CONSULT-II Reference Value ..............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ...............................153
WITH CONSULT-II ............................................153
Wiring Diagram — CVT — STM ...........................154
Diagnostic Procedure ...........................................155
Component Inspection ..........................................156
STEP MOTOR ...................................................156
DTC P1778 STEP MOTOR - FUNCTION ...............157
Description ............................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ....................................157
Possible Cause .....................................................157
DTC Confirmation Procedure ...............................157
WITH CONSULT-II ............................................157
Diagnostic Procedure ...........................................158
CVT INDICATOR CIRCUIT .....................................159
Description ............................................................159
CONSULT-II Reference Value ..............................159
Diagnostic Procedure ...........................................159
CVT INDICATOR SYMPTOM CHART ...............159
TROUBLE DIAGNOSIS FOR SYMPTOMS ............160Wiring Diagram — CVT — NONDTC ...................160
CVT Indicator Lamp Does Not Come On ..............164
SYMPTOM: ........................................................164
DIAGNOSTIC PROCEDURE .............................164
Engine Cannot Be Started in “P” or “N” Position ...165
SYMPTOM: ........................................................165
DIAGNOSTIC PROCEDURE .............................165
In “P” Position, Vehicle Moves Forward or Backward
When Pushed .......................................................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
In “N” Position, Vehicle Moves ..............................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
Large Shock “N” → “R” Position ...........................167
SYMPTOM: ........................................................167
DIAGNOSTIC PROCEDURE .............................167
Vehicle Does Not Creep Backward in “R” Position .168
SYMPTOM: ........................................................168
DIAGNOSTIC PROCEDURE .............................168
Vehicle Does Not Creep Forward in “D” Position ..169
SYMPTOM: ........................................................169
DIAGNOSTIC PROCEDURE .............................169
CVT Does Not Shift ...............................................170
SYMPTOM: ........................................................170
DIAGNOSTIC PROCEDURE .............................170
Cannot Be Changed to Manual Mode ...................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
CVT Does Not Shift in Manual Mode ....................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
Vehicle Does Not Decelerate by Engine Brake .....172
SYMPTOM: ........................................................172
DIAGNOSTIC PROCEDURE .............................172
TRANSMISSION CONTROL MODULE ..................174
Removal and Installation .......................................174
COMPONENTS .................................................174
REMOVAL ..........................................................174
INSTALLATION ..................................................175
SHIFT CONTROL SYSTEM ....................................176
Removal and Installation .......................................176
CONTROL DEVICE COMPONENTS ................176
CONTROL CABLE COMPONENTS ..................177
REMOVAL ..........................................................177
INSTALLATION ..................................................178
Adjustment of CVT Position ..................................178
Checking of CVT Position .....................................179
CVT SHIFT LOCK SYSTEM ...................................180
Description ............................................................180
Shift Lock System Electrical Parts Location ..........180
Wiring Diagram — CVT — SHIFT ........................181
Shift Lock Control Unit Reference Values .............183
SHIFT LOCK HARNESS CONNECTOR TERMI-
NALS LAYOUT ..................................................183
SHIFT LOCK CONTROL UNIT INSPECTION

CVT-28
TROUBLE DIAGNOSIS

4❏ Perform road testCVT-35
4-1.Check before engine is started CVT-37
❏ CVT-164, "CVT Indicator Lamp Does Not Come On"
❏ Perform self-diagnosis. Enter checks for detected items. CVT-47
❏ CVT-53, "DTC U1000 CAN COMMUNICATION LINE"
❏ CVT-56, "DTC P0615 START SIGNAL CIRCUIT"
❏ CVT-60, "DTC P0703 STOP LAMP SWITCH CIRCUIT"
❏ CVT-62, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ CVT-69, "DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT"
❏ CVT-74, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)"
❏ CVT-79, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SEN-
SOR)"
❏ CVT-85, "DTC P0725 ENGINE SPEED SIGNAL"
❏ CVT-87, "DTC P0730 BELT DAMAGE"
❏ CVT-89, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ CVT-94, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ CVT-97, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ CVT-102, "DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE
(LINE PRESSURE SOLENOID VALVE)"
❏ CVT-105, "DTC P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE
(SEC PRESSURE SOLENOID VALVE)"
❏ CVT-108, "DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC
PRESSURE SOLENOID VALVE)"
❏ CVT-113, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
❏ CVT-118, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT
(SEC PRESSURE SENSOR)"
❏ CVT-123, "DTC P0841 PRESSURE SENSOR FUNCTION"
❏ CVT-126, "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT
(PRI PRESSURE SENSOR)"
❏ CVT-131, "DTC P0868 SECONDARY PRESSURE DOWN"
❏ CVT-134, "DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)"
❏ CVT-139, "DTC P1705 THROTTLE POSITION SENSOR"
❏ CVT-141, "DTC P1722 ESTM VEHICLE SPEED SIGNAL"
❏ CVT-143, "DTC P1723 CVT SPEED SENSOR FUNCTION"
❏ CVT-145, "DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM"
❏ CVT-147, "DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT"
❏ CVT-153, "DTC P1777 STEP MOTOR - CIRCUIT"
❏ CVT-157, "DTC P1778 STEP MOTOR - FUNCTION"
4-2.Check at idleCVT-37
❏ CVT-165, "Engine Cannot Be Started in “P” or “N” Position"
❏ CVT-166, "In “P” Position, Vehicle Moves Forward or Backward When Pushed"
❏ CVT-166, "In “N” Position, Vehicle Moves"
❏ CVT-167, "Large Shock “N” → “R” Position"
❏ CVT-168, "Vehicle Does Not Creep Backward in “R” Position"
❏ CVT-169, "Vehicle Does Not Creep Forward in “D” Position"

CVT-38
TROUBLE DIAGNOSIS

4. CHECK “N” POSITION FUNCTION
1. Start engine.
2. Move selector lever to “N” position.
3. Release parking brake.
Does vehicle move forward or backward?
YES >> Mark the box CVT-166, "In “N” Position, Vehicle Moves" on the CVT-27, "DIAGNOSTIC WORK-
SHEET" . Continue “Road Test”.
NO >> GO TO 5.
5. CHECK SHIFT SHOCK
1. Apply foot brake.
2. Move selector lever to “R” position.
Is there large shock when changing from
“N” to “R” position?
YES >> Mark the box CVT-167, "Large Shock “N” → “R” Position" on the CVT-27, "DIAGNOSTIC WORK-
SHEET" . Continue “Road Test”.
NO >> GO TO 6.
6. CHECK “R” POSITION FUNCTION
Release foot brake for several seconds.
Does vehicle creep backward when foot brake is released?
YES >> GO TO 7.
NO >> Mark the box CVT-168, "
Vehicle Does Not Creep Backward in “R” Position" on the CVT-27,
"DIAGNOSTIC WORKSHEET" . Continue “Road Test”.
7. CHECK “D” POSITION FUNCTION
Move selector lever to “D” position and check if vehicle creeps forward.
Does vehicle creep forward in
“D” position?
YES >> Go to CVT-38, "Cruise Test" .
NO >> Mark the box CVT-169, "
Vehicle Does Not Creep Forward in “D” Position" on the CVT-27, "DIAG-
NOSTIC WORKSHEET" . Continue “Road Test”.
Cruise TestBCS001GN
1. CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 1
1. Drive vehicle for approximately 10 minutes to warm engine oil and CVT fluid up to operating temperature.
2. Park vehicle on flat surface.
3. Move selector lever to “P” position.
4. Start engine.
5. Move selector lever to “D” position.
6. Accelerate vehicle to 2/8-way throttle depressing accelerator
pedal constantly.
Read vehicle speed and engine speed. Refer to CVT-40,
"Vehicle Speed at Which Gear Shifting Occurs" .
OK or NG
OK >> GO TO 2.
NG >> Mark the box of CVT-170, "
CVT Does Not Shift" on the
CVT-27, "
DIAGNOSTIC WORKSHEET" . Continue
“Road Test”. CVT fluid operating temperature: 50 - 80°C (122 - 176°F)
SCIA6644E

TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-169
D
E
F
G
H
I
J
K
L
MA
B
CVT

Vehicle Does Not Creep Forward in “D” PositionBCS001MH
SYMPTOM:
Vehicle does not creep forward when selecting “D” position.
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to CVT-47, "
SELF-DIAGNOSTIC RESULT MODE" .
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system. Refer to CVT-47, "Display Items List" .
NO >> GO TO 2.
2. CHECK CVT POSITION
Check CVT position. Refer to CVT-179, "
Checking of CVT Position"
OK or NG
OK >> GO TO 3.
NG >> Adjust CVT position. Refer to CVT-178, "
Adjustment of CVT Position" .
3. CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to CVT-13, "
Checking CVT Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill CVT fluid.
4. CHECK LINE PRESSURE
Check line pressure at idle. Refer to CVT-33, "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 5.
NG >> Check the malfunctioning item. Refer to CVT-34, "
Judgement of Line Pressure Test" .
5. CHECK SYMPTOM
Check again. Refer to CVT-37, "
Check at Idle" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 6.
6. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-40, "
TCM Input/Output Signal Reference Values" .
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the transaxle assembly. Refer to CVT-193, "Removal and Installation" .
NG >> Repair or replace damaged parts.

EC-2 CONSULT-II Reference Value in Data Monitor Mode
.116
On Board Diagnosis Logic ....................................117
DTC Confirmation Procedure ...............................117
Overall Function Check ........................................118
Wiring Diagram .....................................................119
Diagnostic Procedure ...........................................121
Component Inspection ..........................................123
Removal and Installation ......................................123
DTC P0102, P0103 MAF SENSOR .........................124
Component Description ........................................124
CONSULT-II Reference Value in Data Monitor Mode
.124
On Board Diagnosis Logic ....................................124
DTC Confirmation Procedure ...............................124
Wiring Diagram .....................................................126
Diagnostic Procedure ...........................................127
Component Inspection ..........................................129
Removal and Installation ......................................130
DTC P0117, P0118 ECT SENSOR ..........................131
Component Description ........................................131
On Board Diagnosis Logic ....................................131
DTC Confirmation Procedure ...............................132
Wiring Diagram .....................................................133
Diagnostic Procedure ...........................................134
Component Inspection ..........................................135
Removal and Installation ......................................135
DTC P0122, P0123 TP SENSOR ............................136
Component Description ........................................136
CONSULT-II Reference Value in Data Monitor Mode
.136
On Board Diagnosis Logic ....................................136
DTC Confirmation Procedure ...............................137
Wiring Diagram .....................................................138
Diagnostic Procedure ...........................................139
Component Inspection ..........................................142
Removal and Installation ......................................142
DTC P0132 HO2S1 .................................................143
Component Description ........................................143
CONSULT-II Reference Value in Data Monitor Mode
.143
On Board Diagnosis Logic ....................................143
DTC Confirmation Procedure ...............................144
Wiring Diagram .....................................................145
Diagnostic Procedure ...........................................146
Component Inspection ..........................................148
Removal and Installation ......................................149
DTC P0134 HO2S1 .................................................150
Component Description ........................................150
CONSULT-II Reference Value in Data Monitor Mode
.150
On Board Diagnosis Logic ....................................150
Overall Function Check ........................................151
Wiring Diagram .....................................................152
Diagnostic Procedure ...........................................153
Component Inspection ..........................................154
Removal and Installation ......................................156
DTC P0222, P0223 TP SENSOR ............................157
Component Description ........................................157CONSULT-II Reference Value in Data Monitor Mode
.157
On Board Diagnosis Logic ....................................157
DTC Confirmation Procedure ................................158
Wiring Diagram .....................................................159
Diagnostic Procedure ............................................160
Component Inspection ..........................................163
Removal and Installation .......................................163
DTC P0327, P0328 KS ............................................164
Component Description ........................................164
On Board Diagnosis Logic ....................................164
DTC Confirmation Procedure ................................164
Wiring Diagram .....................................................165
Diagnostic Procedure ............................................166
Component Inspection ..........................................168
Removal and Installation .......................................168
DTC P0335 CKP SENSOR (POS) ..........................169
Component Description ........................................169
CONSULT-II Reference Value in Data Monitor Mode
.169
On Board Diagnosis Logic ....................................169
DTC Confirmation Procedure ................................170
Wiring Diagram .....................................................171
Diagnostic Procedure ............................................173
Component Inspection ..........................................174
Removal and Installation .......................................175
DTC P0340 CMP SENSOR (PHASE) .....................176
Component Description ........................................176
CONSULT-II Reference Value in Data Monitor Mode
.176
On Board Diagnosis Logic ....................................176
DTC Confirmation Procedure ................................177
Wiring Diagram .....................................................178
Diagnostic Procedure ............................................179
Component Inspection ..........................................182
Removal and Installation .......................................182
DTC P0500 VSS ......................................................183
Description ............................................................183
On Board Diagnosis Logic ....................................183
DTC Confirmation Procedure ................................183
Overall Function Check .........................................184
Diagnostic Procedure ............................................184
DTC P0550 PSP SENSOR ......................................185
Component Description ........................................185
CONSULT-II Reference Value in Data Monitor Mode
.185
On Board Diagnosis Logic ....................................185
DTC Confirmation Procedure ................................185
Wiring Diagram .....................................................186
Diagnostic Procedure ............................................187
Component Inspection ..........................................189
Removal and Installation .......................................189
DTC P0605 ECM .....................................................190
Component Description ........................................190
On Board Diagnosis Logic ....................................190
DTC Confirmation Procedure ................................190
Diagnostic Procedure ............................................192
DTC P1065 ECM POWER SUPPLY ........................193
Component Description ........................................193

EC-10
[QR]
INDEX FOR DTC

[QR]INDEX FOR DTCPFP:00024
DTC No. IndexBBS005B7
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-113, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
DTC*1Items
(CONSULT-II screen terms)Reference page
CONSULT-II
ECM*
2
No DTC
Flashing*3NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.EC-37
U1000
1000*4CAN COMM CIRCUITEC-113
U1001
1001*4CAN COMM CIRCUITEC-113
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.—
P0011 0011 INT/V TIM CONT-B1EC-116
P0102 0102 MAF SEN/CIRCUITEC-124
P0103 0103 MAF SEN/CIRCUITEC-124
P0117 0117 ECT SEN/CIRCEC-131
P0118 0118 ECT SEN/CIRCEC-131
P0122 0122 TP SEN 2/CIRCEC-136
P0123 0123 TP SEN 2/CIRCEC-136
P0132 0132 HO2S1 (B1)EC-143
P0134 0134 HO2S1 (B1)EC-150
P0222 0222 TP SEN 1/CIRCEC-157
P0223 0223 TP SEN 1/CIRCEC-157
P0327 0327 KNOCK SEN/CIRC-B1EC-164
P0328 0328 KNOCK SEN/CIRC-B1EC-164
P0335 0335 CKP SEN/CIRCUITEC-169
P0340 0340 CMP SEN/CIRC-B1EC-176
P0500 0500 VEH SPEED SEN/CIRCEC-183
P0550 0550 PW ST P SEN/CIRCEC-185
P0605 0605 ECMEC-190
P1065 1065 ECM BACK UP/CIRCUITEC-193
P1121 1121 ETC ACTREC-197
P1122 1122 ETC FUNCTION/CIRCEC-200
P1124 1124 ETC MOT PWREC-207
P1126 1126 ETC MOT PWREC-207
P1128 1128 ETC MOTEC-213
P1217 1217 ENG OVER TEMPEC-218
P1225 1225 CTP LEARNINGEC-229
P1226 1226 CTP LEARNINGEC-231
P1229 1229 SENSOR POWER/CIRCEC-233
P1610 - P1615 1610 - 1615 NATS MALFUNCTIONEC-32
P1706 1706 P-N POS SW/CIRCUITEC-238
P1720 1720 V/SP SEN (A/T OUT)EC-243

EC-12
[QR]
INDEX FOR DTC

Alphabetical IndexBBS005B8
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-113, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
ECM*2
APP SEN 1/CIRC P2122 2122EC-251
APP SEN 1/CIRC P2123 2123EC-251
APP SEN 2/CIRC P2127 2127EC-258
APP SEN 2/CIRC P2128 2128EC-258
APP SENSOR P2138 2138EC-272
BRAKE SW/CIRCUIT P1805 1805EC-245
CAN COMM CIRCUIT U1000
1000*4EC-113
CAN COMM CIRCUIT U1001
1001*4EC-113
CKP SEN/CIRCUIT P0335 0335EC-169
CMP SEN/CIRC-B1 P0340 0340EC-176
CTP LEARNING P1225 1225EC-229
CTP LEARNING P1226 1226EC-231
ECM P0605 0605EC-190
ECM BACK UP/CIRCUIT P1065 1065EC-193
ECT SEN/CIRC P0117 0117EC-131
ECT SEN/CIRC P0118 0118EC-131
ENG OVER TEMP P1217 1217EC-218
ETC ACTR P1121 1121EC-197
ETC FUNCTION/CIRC P1122 1122EC-200
ETC MOT P1128 1128EC-213
ETC MOT PWR P1124 1124EC-207
ETC MOT PWR P1126 1126EC-207
HO2S1 (B1) P0132 0132EC-143
HO2S1 (B1) P0134 0134EC-150
INT/V TIM CONT-B1 P0011 0011EC-116
KNOCK SEN/CIRC-B1 P0327 0327EC-164
KNOCK SEN/CIRC-B1 P0328 0328EC-164
MAF SEN/CIRCUIT P0102 0102EC-124
MAF SEN/CIRCUIT P0103 0103EC-124
NATS MALFUNCTION P1610 - P1615 1610 - 1615EC-32
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.No DTC
Flashing*3EC-37
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000 —
P-N POS SW/CIRCUIT P1706 1706EC-238
PW ST P SEN/CIRC P0550 0550EC-185
SENSOR POWER/CIRC P1229 1229EC-233
TP SEN 1/CIRC P0222 0222EC-157