trunk NISSAN TEANA 2008 Service Manual

TAKE AWAY WARNING DOES NOT OPERATE
DLK-177
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
 Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to DLK-7, "Work
Flow".
 Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm
the list above twice in order to ensure proper operation. Refer to DLK-31, "
WARNING FUNCTION : System
Description".
 Door lock function is normal.
INTELLIGENT KEY IS REMOVED FROM KEY SLOT : Diagnosis Procedure
INFOID:0000000003795033
1.CHECK KEY SLOT
Check key slot.
Refer to DLK-86, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK COMBINATION METER DISPLAY
Check combination meter display.
Refer to DLK-93, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Refer to DLK-50, "
DTC Logic" (instrument center).
Refer to DLK-52, "
DTC Logic" (console).
Refer to DLK-54, "
DTC Logic" (trunk room).
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK KEY SLOT ILLUMINATION
Check key slot illumination.
Refer to DLK-88, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

DLK-178
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE
INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE
DescriptionINFOID:0000000003795034
NOTE:
 Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to DLK-7, "
Work
Flow".
 Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm
the list above twice in order to ensure proper operation. Refer to DLK-31, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000003795035
1.CHECK “LO- BATT OF KEY FOB WARN” SETTING IN “WORK SUPPORT”
Check “LO- BATT OF KEY FOB WARN” setting in “WORK SUPPORT”.
Refer to DLK-43, "
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Set “LO- BATT OF KEY FOB WARN” setting in “WORK SUPPORT”.
2.CHECK INTELLIGENT KEY BATTERY
Check Intelligent Key battery.
Refer to DLK-84, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CHECK COMBINATION METER DISPLAY
Check combination meter display.
Refer to DLK-93, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Refer to DLK-50, "
DTC Logic" (instrument center).
Refer to DLK-52, "
DTC Logic" (console).
Refer to DLK-54, "
DTC Logic" (trunk room).
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK KEY SLOT ILLUMINATION
Check key slot illumination.
Refer to DLK-88, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

DOOR LOCK OPERATION WARNING DOES NOT OPERATE WITH DOOR RE-
QUEST SWITCH
DLK-179
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DOOR LOCK OPERATION WARNING DOES NOT OPERATE WITH DOOR
REQUEST SWITCH
DescriptionINFOID:0000000003795036
NOTE:
 Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to DLK-7, "
Work
Flow".
 Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm
the list above twice in order to ensure proper operation. Refer to DLK-31, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000003795037
1.CHECK DOOR LOCK FUNCTION
Check door lock function by door request switch.
Does door lock/unlock with door request switch?
YES >> GO TO 2.
NO >>  Go to DLK-161, "
DRIVER SIDE : Description" (driver side).
Go to DLK-161, "
PASSENGER SIDE : Description" (passenger side).
Go to DLK-162, "
TRUNK : Description" (trunk room).
2.CHECK DOOR SWITCH
Check door switch (driver side).
Refer to DLK-57, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to DLK-82, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Refer to DLK-50, "
DTC Logic" (instrument center).
Refer to DLK-52, "
DTC Logic" (console).
Refer to DLK-54, "
DTC Logic" (trunk room).
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

DLK-184
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Inspection Procedure
INFOID:0000000003941378
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. Cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Never use silicone spray to isolate a squeak or rattle. If the area is saturated with silicone, the recheck
of repair becomes impossible.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the following:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. The areas can usually be insulated with felt cloth tape or insulator foam blocks to
repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer.
In addition look for the following:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.

TRUNK LID
DLK-213
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded ViewINFOID:0000000003813412
REMOVAL
ADJUSTMENT
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

DLK-214
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000003813413
CAUTION:
Operate with two workers, because of its heavy weight.
REMOVAL
1. Remove the trunk lid finisher inner. Refer to INT-59, "Removal and Installation"
2. Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.
3. Remove trunk lid stay at trunk lid side. Refer to DLK-218, "
TRUNK LID STAY : Removal and Installation".
4. Remove the trunk lid hinge mounting bolts on trunk lid side and remove the trunk lid assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
 Check trunk lid open/close, lock/unlock operation after installation.
 After installation, perform fitting adjustment. Refer to DLK-215, "
TRUNK LID ASSEMBLY : Adjust-
ment".
1. Trunk lid assembly 2. Trunk lid hinge 3. Trunk lid striker
4. Body side outer 5. Rear combination lamp 6. Rear bumper fascia
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2393GB

TRUNK LID
DLK-215
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID ASSEMBLY : AdjustmentINFOID:0000000003813414
Check the clearance and surface height between trunk lid and each part by visually and touching.
If the clearance and surface height are out of specification, adjust them according to the procedures shown
below.
Unit: mm (in)
1. Loosen trunk lid hinge mounting bolts (trunk lid side).
2. Remove trunk rear finisher. Refer to INT-57, "
Removal and Installation".
3. Loosen trunk lid striker mounting bolts.
4. Lift up trunk lid approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that it
is engaged firmly with trunk lid closed.
5. Check the clearance and surface height.
6. Finally tighten trunk lid hinge and trunk lid striker.
7. Install trunk rear finisher. Refer to INT-57, "
Removal and Installation".
TRUNK LID STRIKER ADJUSTMENT
Adjust trunk lid striker so that it becomes parallel with trunk lid lock insertion direction.
TRUNK LID STRIKER
Portion StandardDifference
(RH/LH, MAX)
Trunk lid – Body side outer A – AD Clearance2.5 – 4.5
(0.098 – 0.177)1.0 (0.039)
ESurface
height−1.5 – 0.5
(−0.059 – 0.020)1.4 (0.055)
Trunk lid – Rear combina-
tion lampB – BF Clearance2.9 – 6.5
(0.114 – 0.256)2.0 (0.079)
GSurface
height−2.3 – 1.3
(−0.091 – 0.051)2.0 (0.079)
Trunk lid – Rear bumper fas-
ciaC – C H Clearance5.0 – 9.0
(0.197 – 0.354)—

DLK-216
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STRIKER : Exploded View
INFOID:0000000003819763
TRUNK LID STRIKER : Removal and InstallationINFOID:0000000003813416
REMOVAL
1. Remove trunk rear finisher. Refer to INT-57, "Removal and Installation".
2. Remove mounting bolts, and then remove trunk lid striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Check trunk lid open/close, lock/unlock operation after installation.
 When removing and installing trunk lid striker, perform the fitting adjustment. Refer to DLK-215,
"TRUNK LID ASSEMBLY : Adjustment".
TRUNK LID HINGE
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B.: Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

TRUNK LID
DLK-217
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID HINGE : Exploded ViewINFOID:0000000003819765
TRUNK LID HINGE : Removal and InstallationINFOID:0000000003813418
REMOVAL
1. Remove trunk lid assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal and Installation".
2. Remove trunk lid stay from trunk lid hinge. Refer to DLK-218, "
TRUNK LID STAY : Removal and Installa-
tion".
3. Remove trunk lid hinge mounting nuts (body side), and then remove trunk lid hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 Check trunk lid open/close, lock/unlock operation after installation.
 Check trunk lid hinge rotating part for poor lubrication. If necessary, apply body grease.
 When removing and installing trunk lid assembly, perform the fitting adjustment. Refer to DLK-215,
"TRUNK LID ASSEMBLY : Adjustment".
 After installation, apply touch-up paint (the body color) onto the head of trunk lid hinge mounting
bolts.
TRUNK LID STAY
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B. : Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB

DLK-218
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID STAY : Exploded View
INFOID:0000000003819766
TRUNK LID STAY : Removal and InstallationINFOID:0000000003813420
REMOVAL
1. Support trunk lid with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the trunk lid open when removing the trunk
lid stay.
2. Remove the metal clip (3) located on the connection between
the trunk lid stay (1) and the stud ball (2) (trunk lid side) by using
a flat-bladed screwdriver (A).
3. Remove trunk lid stay (trunk lid side).
4. In the same way, remove trunk lid stay (body side).
INSTALLATION
Install in the reverse order of removal.
1. Trunk lid 2. Trunk lid weather-strip 3. Cap
4. Stopper 5. Trunk lid hinge 6. Trunk lid striker
7. Bumper rubber 8. Trunk lid lock assembly 9. Trunk lid stay
A : Center mark (upper) B.: Center mark (lower)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2389GB
JMKIA2255ZZ