phone NISSAN TEANA 2008 Owner's Manual

AV
NAVI CONTROL UNIT
AV-525
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
16
(P)—AV communication signal
(L)Input/
Output—— —
19
(BR/L)Ground RGB image signal (R: red) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
20
(Y/L)GroundRGB image signal (G:
green)OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
21
(Y/G)Ground RGB image signal (B: blue) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
22
(W/L)Ground RGB ground —Ignition
switch
ON—0 V
23
(L)Ground RGB synchronizing signal OutputIgnition
switch
ON—
24 GroundRGB synchronizing signal
ground—Ignition
switch
ON —0 V
28
(L)30
(P)Voice guidance signal OutputIgnition
switch
ONVoice guidance output.
29 — Shield — — — —Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2238J
SKIB2236J
SKIB2237J
SKIB3603E
SKIB1990E

AV-526
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
NAVI CONTROL UNIT
33
(B)35
(W)TEL voice signal OutputIgnition
switch
ONTEL voice output.
34 — Shield — — — —
39
(B)42 Microphone VCC OutputIgnition
switch
ON— 5.0 V
41
(W)42 Microphone signal InputIgnition
switch
ONGive a voice.
42 — Microphone signal shield — — — —
49 Ground GPS antenna signal InputIgnition
switch
ONNot connected to GPS an-
tenna connector.5.0 V
50 — Shield — — — —
51 Ground TEL antenna signalInput/
OutputIgnition
switch
ONNot connected to TEL an-
tenna connector.3.3 V
52 — Shield — — — —Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB1990E
PKIB5037J

AV-640
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003765976
RELATED TO BASIC OPERATION
RELATED TO HANDS FREE PHONE
 Check that the cellular phone is corresponding type (Bluetooth™ correspond) when the hands free related
malfunction vehicle is in service before performing a diagnosis,.
 There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone.
Simple check for Bluetooth™ communication
If cellular phone and NAVI control unit cannot be connected with Bluetooth™ communication, following proce-
dure allows the technician to judge which device has malfunction.
1. Turn on a cellular phone, not connecting Bluetooth
™ communication.
2. Start CONSULT-III, then start Windows
®.
3. Set CONSULT-III near a cellular phone.
4. When operated Bluetooth
™ registration by cellular phone, check
if CONSULT-III
* would be displayed on the device name.
(If other Bluetooth
™ device is located near cellular phone, a
name of the device would be displayed also.)
NOTE:
*:Displayed device name is “NISSAN- ”.
 If no device name is displayed, cellular phone is malfunction.
Repair the cellular phone first, then perform diagnosis.
 If CONSULT-III is displayed on device name, cellular phone is nor-
mal. Perform diagnosis as per the following table.
Symptoms Check items Possible malfunction location / Action to take
Multifunction switch and preset
switch operation does not work. All switches cannot be operated
 “MULTI AV” is displayed on system
selection screen when the CON-
SULT-III is started.Perform CONSULT-III self-diagnosis. Refer to AV- 4 3 4 ,
"CONSULT-III Function (MULTI AV)".
 All switches cannot be operated
 “MULTI AV” is not displayed on sys-
tem selection screen when the CON-
SULT-III is started.AV control unit power supply and ground circuit malfunc-
tion. Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis
Procedure".
Only specified switch cannot be operat-
ed.Multifunction switch or preset switch malfunction.
Replace multifunction switch or preset switch.
For multifunction switch, refer to AV- 6 5 9 , "
Removal and
Installation".
For preset switch, refer to AV- 6 6 0 , "
Removal and Instal-
lation".
Fuel economy display, vehicle set-
ting operation is abnormal.There is malfunction in the CONSULT-
III self-diagnosis result.Perform detected DTC diagnosis.
There is no malfunction in the self-diag-
nosis results.Ignition signal circuit malfunction.
Refer to AV- 4 6 4 , "
AV CONTROL UNIT : Diagnosis Pro-
cedure".
Guide sound is not heard.On the setting display select “system
sound (guide sound volume, etc.),” and
confirm that guide sound is ON.Voice guidance signal circuit malfunction.
JPNIA0441GB

AV
MULTI AV SYSTEM SYMPTOMS
AV-641
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO REAR VIEW MONITOR
RELATED TO RGB IMAGE
Symptoms Check items Possible malfunction location / Action to take
Does not recognize cellular
phone connection. (no connec-
tion is displayed on the display
at the guide.)There is malfunction in the CONSULT-III
self-diagnosis result.Perform detected DTC diagnosis.
There is no malfunction in the CONSULT-
III self-diagnosis results.Repeat the registration of cellular phone.
Hands free phone cannot be
established. Hands free phone operation can be
made, but the communication cannot
be established.
 Hands free phone operation can be per-
formed, however, voice between each
other cannot be heard during the con-
versation.NAVI control unit malfunction.
Replace NAVI control unit.
Refer to AV- 6 4 9 , "
Removal and Installation".
The other party's voice cannot
be heard by hands free phone.Check the “Handsfree Voice Microphone
Test”in Confirmation/Adjustment mode if
sound is heard. Refer to AV- 4 1 9 , "
Diagno-
sis Description".NAVI control unit malfunction.
Replace NAVI control unit.
Refer to AV- 6 4 9 , "Removal and Installation".
Check the “Handsfree Voice Microphone
Test”in Confirmation/Adjustment mode if
sound is not heard. Refer to AV- 4 1 9 , "
Di-
agnosis Description"
TEL voice signal circuit.
Originating sound is not heard
by the other party with hands
free phone communication.Sound operation function is normal.NAVI control unit malfunction.
Replace NAVI control unit.
Refer to AV- 6 4 9 , "
Removal and Installation".
Sound operation function does not work.Microphone signal circuit malfunction.
Refer to AV- 4 8 2 , "
Diagnosis Procedure".
Symptoms Check itemsProbable malfunction location / Action
to take
It cannot be switched to rear view
monitor even when the selector le-
ver is in the reverse position. There is malfunction in the CONSULT-III self-diagno-
sis result.Perform CONSULT-III self-diagnosis.
Refer to AV- 4 3 4 , "
CONSULT-III Func-
tion (MULTI AV)".
There is not malfunction in the CONSULT-III self-diag-
nosis result.Reverse signal circuit malfunction.(AV
control unit)
Camera image is not shown. DVD and AUX images are normal.  Rear view camera power supply cir-
cuit malfunction.
Refer to AV- 4 8 4 , "
Diagnosis Proce-
dure".
 Camera image signal circuit malfunc-
tion.
Refer to AV- 4 8 5 , "
Diagnosis Proce-
dure".
Possible route line is indicated ab-
normally when camera image is dis-
played.The “Steer. Angle Sensor” is not turned ON at “Con-
nection Confirmation” of “Camera Cont.”Steering angle sensor signal circuits.
Refer to AV- 4 8 7 , "
Diagnosis Proce-
dure".
Camera image is rolling. AUX image is rolling Horizontal synchronizing (HP) signal
circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 4 7 4 , "
Diagnosis Proce-
dure".
 Vertical synchronizing (VP) signal cir-
cuit malfunction between AV control
unit and display unit.
Refer to AV- 4 7 5 , "
Diagnosis Proce-
dure".

AV-664
< ON-VEHICLE REPAIR >[BOSE AUDIO WITH NAVIGATION]
MICROPHONE
MICROPHONE
Exploded ViewINFOID:0000000003766009
REMOVAL
Refer to INL-89, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003766010
REMOVAL
1. Remove map lamp assembly. Refer to INL-89, "Removal and Installation".
2. Remove microphone(1), stretching pawls of map lamp assem-
bly.
INSTALLATION
Installation is the reverse order of removal.
JSNIA0132ZZ
1. Microphone
JSNIA0132ZZ

PRECAUTIONS
EC-409
< PRECAUTION >[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
When installing C.B. ham radio or a mobile phone, be sure to
observe the following as it may adversely affect electronic
control systems depending on installation location.
-Keep the antenna as far as possible from the electronic con-
trol units.
-Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Never let them run parallel for a long distance.
-Adjust the antenna and feeder line so that the standing-wave
ratio can be kept smaller.
-Be sure to ground the radio to vehicle body.
SEF708Y