lock NISSAN TEANA 2008 Service Manual

STR-18
< ON-VEHICLE REPAIR >
STARTER MOTOR
1. Inspect pinion teeth.
 Replace pinion if teeth are worn or damaged. (Also check con-
dition of ring gear teeth.)
2. Inspect reduction gear teeth.
 Replace reduction gear if teeth are worn or damaged. (Also
check condition of armature shaft gear teeth.)
3. Check to see if pinion locks in one direction and rotates
smoothly in the opposite direction.
 Replace pinion assembly if it is locked or rotated in both direc-
tions or unusual resistance is evident.
BRUSH HOLDER ASSEMBLY
Brush
 Check wear of brush.
 Replace brush if the measurement value is less than the specified
value.
Brush Spring
 Check brush spring tension with brush spring detached from
brush.
 Replace brush spring if the measurement value is less than the
specified value.
Brush Holder
1. Perform insulation test between brush holder (positive side) and
its base (negative side).
- Replace brush holder assembly if continuity does not exist.
2. Check brush to see if it moves smoothly.
- If brush holder is bent, replace it if sliding surface is dirty, clean.
YOKE CHECK
SEL630BA
Minimum length of brush : Refer to SDS STR-26,
"StarterMotor".
SEL014Z
Spring tension (with new
brush): Refer to SDS STR-26,
"StarterMotor".
SEL015Z
SKIB0460E

STARTER MOTOR
STR-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
MA
STR
N
P O
1. Inspect pinion teeth.
 Replace pinion if teeth are worn or damaged. (Also check con-
dition of ring gear teeth.)
2. Inspect reduction gear teeth.
 Replace reduction gear if teeth are worn or damaged. (Also
check condition of armature shaft gear teeth.)
3. Check to see if pinion locks in one direction and rotates
smoothly in the opposite direction.
 Replace pinion assembly if it is locked or rotated in both direc-
tions or unusual resistance is evident.
BRUSH HOLDER ASSEMBLY
Brush
 Check wear of brush.
 Replace brush if the measurement value is less than the specified
value.
Brush Spring
 Check brush spring tension with brush spring detached from
brush.
 Replace brush spring if the measurement value is less than the
specified value.
Brush Holder
1. Perform insulation test between brush holder (positive side) and
its base (negative side).
- Replace brush holder assembly if continuity does not exist.
2. Check brush to see if it moves smoothly.
- If brush holder is bent, replace it if sliding surface is dirty, clean.
YOKE CHECK
SEL630BA
Minimum length of brush : Refer to SDS STR-26,
"StarterMotor".
SEL014Z
Spring tension (with new
brush): Refer to SDS STR-26,
"StarterMotor".
SEL015Z
SKIB0460E

TM-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION TM
A
B
TM
N
O
P
CONTENTS
TRANSAXLE & TRANSMISSION
CVT: RE0F09B
BASIC INSPECTION ....................................
9
DIAGNOSIS AND REPAIR WORK FLOW .........9
Work Flow .................................................................9
Diagnostic Work Sheet ............................................10
INSPECTION AND ADJUSTMENT ....................12
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ........................................................
12
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Precaution for TCM and CVT
Assembly Replacement ..........................................
12
FUNCTION DIAGNOSIS ..............................13
CVT SYSTEM .....................................................13
System Diagram ......................................................13
Component Parts Location ......................................14
MECHANICAL SYSTEM ....................................16
Cross-Sectional View ..............................................16
System Diagram ......................................................17
System Description .................................................17
Component Parts Location ......................................18
Component Description ...........................................19
HYDRAULIC CONTROL SYSTEM ....................20
System Diagram ......................................................20
System Description .................................................20
Component Parts Location ......................................21
Component Description ...........................................22
CONTROL SYSTEM ..........................................23
System Diagram ......................................................23
System Description .................................................23
Component Parts Location ......................................25
Component Description ...........................................26
LOCK-UP AND SELECT CONTROL SYSTEM
....
27
System Diagram ......................................................27
System Description ..................................................27
Component Parts Location ......................................28
Component Description ...........................................29
SHIFT CONTROL SYSTEM ..............................30
System Diagram ......................................................30
System Description ..................................................30
Component Parts Location ......................................31
Component Description ...........................................32
SHIFT LOCK SYSTEM .....................................33
System Description ..................................................33
Component Parts Location ......................................34
Component Description ...........................................34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ....35
Diagnosis Description ..............................................35
DIAGNOSIS SYSTEM (TCM) ............................37
CONSULT-III Function (TRANSMISSION) ..............37
Diagnostic Tool Function .........................................40
COMPONENT DIAGNOSIS .........................41
U1000 CAN COMM CIRCUIT ...........................41
Description ...............................................................41
DTC Logic ................................................................41
Diagnosis Procedure ...............................................41
P0615 START SIGNAL .....................................42
Description ...............................................................42
DTC Logic ................................................................42
Diagnosis Procedure ...............................................42
P0703 STOP LAMP SWITCH ...........................44
Description ...............................................................44
DTC Logic ................................................................44
Diagnosis Procedure ...............................................44
Component Inspection (Stop Lamp Switch) ............45
P0705 PARK/NEUTRAL POSITION SWITCH ...47
Description ...............................................................47

TM-2
DTC Logic ...............................................................47
Diagnosis Procedure ..............................................47
Component Inspection ............................................48
P0710 CVT FLUID TEMPERATURE SENSOR
...
50
Description ..............................................................50
DTC Logic ...............................................................50
Diagnosis Procedure ..............................................50
Component Inspection (CVT Fluid Temperature
Sensor) ...................................................................
51
P0715 INPUT SPEED SENSOR (PRI SPEED
SENSOR) ...........................................................
52
Description ..............................................................52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) .............................
55
Description ..............................................................55
DTC Logic ...............................................................55
Diagnosis Procedure ..............................................55
P0725 ENGINE SPEED SIGNAL ......................59
Description ..............................................................59
DTC Logic ...............................................................59
Diagnosis Procedure ..............................................59
P0730 BELT DAMAGE ......................................60
Description ..............................................................60
DTC Logic ...............................................................60
Diagnosis Procedure ..............................................60
P0740 TORQUE CONVERTER CLUTCH SO-
LENOID VALVE .................................................
62
Description ..............................................................62
DTC Logic ...............................................................62
Diagnosis Procedure ..............................................62
Component Inspection (Torque Converter Clutch
Solenoid Valve) ......................................................
63
P0744 A/T TCC S/V FUNCTION (LOCK -UP) ...64
Description ..............................................................64
DTC Logic ...............................................................64
Diagnosis Procedure ..............................................64
Component Inspection (Torque Converter Clutch
Solenoid Valve) ......................................................
65
Component Inspection (Lock-up Select Solenoid
Valve) .....................................................................
65
P0745 LINE PRESSURE SOLENOID VALVE ...66
Description ..............................................................66
DTC Logic ...............................................................66
Diagnosis Procedure ..............................................66
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
67
P0746 PRESSURE CONTROL SOLENOID A
PERFORMANCE (LINE PRESSURE SOLE-
NOID VALVE) ....................................................
68
Description ..............................................................68
DTC Logic ...............................................................68
Diagnosis Procedure ...............................................68
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
69
P0776 PRESSURE CONTROL SOLENOID B
PERFORMANCE (SEC PRESSURE SOLE-
NOID VALVE) ....................................................
70
Description ..............................................................70
DTC Logic ...............................................................70
Diagnosis Procedure ...............................................70
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
71
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
71
P0778 PRESSURE CONTROL SOLENOID B
ELECTRICAL (SEC PRESSURE SOLENOID
VALVE) ..............................................................
72
Description ..............................................................72
DTC Logic ...............................................................72
Diagnosis Procedure ...............................................72
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
73
P0840 TRANSMISSION FLUID PRESSURE
SENSOR A (SEC PRESSURE SENSOR) .........
74
Description ..............................................................74
DTC Logic ...............................................................74
Diagnosis Procedure ...............................................74
P0841 PRESSURE SENSOR FUNCTION ........77
Description ..............................................................77
DTC Logic ...............................................................77
Diagnosis Procedure ...............................................77
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
78
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
78
P0845 TRANSMISSION FLUID PRESSURE
SENSOR B (PRI PRESSURE SENSOR) ..........
80
Description ..............................................................80
DTC Logic ...............................................................80
Diagnosis Procedure ...............................................80
P0868 SECONDARY PRESSURE DOWN ........83
Description ..............................................................83
DTC Logic ...............................................................83
Diagnosis Procedure ...............................................83
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
84

TM-3
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
84
P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) .............................................
85
Description ..............................................................85
DTC Logic ...............................................................85
Diagnosis Procedure ...............................................85
P1705 THROTTLE POSITION SENSOR ...........88
Description ..............................................................88
DTC Logic ...............................................................88
Diagnosis Procedure ...............................................88
P1722 ESTM VEHICLE SPEED SIGNAL ..........89
Description ..............................................................89
DTC Logic ...............................................................89
Diagnosis Procedure ...............................................89
P1723 CVT SPEED SENSOR FUNCTION ........91
Description ..............................................................91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
P1726 ELECTRIC THROTTLE CONTROL
SYSTEM .............................................................
93
Description ..............................................................93
DTC Logic ...............................................................93
Diagnosis Procedure ...............................................93
P1740 LOCK-UP SELECT SOLENOID
VALVE ................................................................
94
Description ..............................................................94
DTC Logic ...............................................................94
Diagnosis Procedure ...............................................94
Component Inspection (Lock-up Select Solenoid
Valve) ......................................................................
95
P1745 LINE PRESSURE CONTROL .................96
Description ..............................................................96
DTC Logic ...............................................................96
Diagnosis Procedure ...............................................96
P1777 STEP MOTOR .........................................97
Description ..............................................................97
DTC Logic ...............................................................97
Diagnosis Procedure ...............................................97
Component Inspection (Step Motor) .......................98
P1778 STEP MOTOR - FUNCTION .................100
Description ............................................................100
DTC Logic .............................................................100
Diagnosis Procedure .............................................100
SHIFT POSITION INDICATOR CIRCUIT .........102
Description ............................................................102
Component Function Check ..................................102
Diagnosis Procedure .............................................102
SHIFT LOCK SYSTEM .....................................103
Description .............................................................103
Wiring Diagram - CVT SHIFT LOCK SYSTEM - ...103
Component Function Check ..................................105
Diagnosis Procedure .............................................106
Component Inspection (Stop Lamp Switch) ..........107
SPORT MODE SWITCH .................................108
Description .............................................................108
Component Function Check ..................................108
Diagnosis Procedure .............................................108
ECU DIAGNOSIS .......................................111
TCM .................................................................111
Reference Value ....................................................111
Wiring Diagram - CVT CONTROL SYSTEM - .......116
Fail-safe .................................................................120
DTC Inspection Priority Chart ................................121
DTC Index .............................................................121
SYMPTOM DIAGNOSIS ............................123
SYSTEM SYMPTOM .......................................123
Symptom Table .....................................................123
PRECAUTION ............................................135
PRECAUTIONS ...............................................135
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
135
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
135
Precaution for Procedure without Cowl Top Cover ..136
Precaution for On Board Diagnosis (OBD) System
of CVT and Engine ................................................
136
Precaution for TCM and CVT Assembly Replace-
ment .......................................................................
136
Removal and Installation Procedure for CVT Unit
Connector ..............................................................
136
Precaution .............................................................138
Service Notice or Precaution .................................138
ATFTEMP COUNT Conversion Table ...................139
PREPARATION .........................................140
PREPARATION ...............................................140
Special Service Tools ............................................140
Commercial Service Tools .....................................140
ON-VEHICLE MAINTENANCE ..................142
CVT FLUID ......................................................142
Inspection ..............................................................142
Changing ...............................................................143
STALL TEST ...................................................144
Inspection and Judgment ......................................144
LINE PRESSURE TEST ..................................146
Inspection and Judgment ......................................146

TM-4
ROAD TEST .....................................................148
Description .............................................................148
Check before Engine Is Started .............................148
Check at Idle ..........................................................149
Cruise Test ............................................................150
CVT POSITION ................................................152
Inspection and Adjustment ....................................152
ON-VEHICLE REPAIR ...............................153
TRANSMISSION CONTROL MODULE ..........153
Exploded View .......................................................153
Removal and Installation .......................................153
Adjustment .............................................................154
CONTROL DEVICE .........................................155
Exploded View .......................................................155
Removal and Installation .......................................155
Inspection and Adjustment ....................................156
CONTROL CABLE ..........................................157
Exploded View .......................................................157
Removal and Installation .......................................157
Inspection and Adjustment ....................................158
OIL PAN ...........................................................159
Exploded View .......................................................159
Removal and Installation .......................................159
Inspection ..............................................................160
SECONDARY SPEED SENSOR .....................161
Exploded View .......................................................161
Removal and Installation .......................................161
Inspection ..............................................................161
DIFFERENTIAL SIDE OIL SEAL ....................162
Exploded View .......................................................162
Removal and Installation .......................................162
Inspection ..............................................................163
AIR BREATHER HOSE ...................................164
Exploded View .......................................................164
Removal and Installation .......................................164
FLUID COOLER SYSTEM ...............................165
Exploded View .......................................................165
Removal and Installation .......................................165
Inspection ..............................................................167
REMOVAL AND INSTALLATION ..............168
TRANSAXLE ASSEMBLY ..............................168
Exploded View .......................................................168
Removal and Installation .......................................168
Inspection ..............................................................170
DISASSEMBLY AND ASSEMBLY ............172
TORQUE CONVERTER ..................................172
Exploded View .......................................................172
Disassembly ..........................................................172
Assembly ..............................................................172
Inspection ..............................................................173
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
174
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
174
General Specification ............................................174
Vehicle Speed When Shifting Gears .....................174
Stall Speed ............................................................174
Line Pressure ........................................................174
Solenoid Valves ....................................................175
CVT Fluid Temperature Sensor ............................175
Primary Speed Sensor ..........................................175
Secondary Speed Sensor .....................................175
Step Motor ............................................................175
Torque Converter ..................................................175
CVT: RE0F10A
BASIC INSPECTION .................................
176
DIAGNOSIS AND REPAIR WORK FLOW .......176
Work Flow .............................................................176
Diagnostic Work Sheet .........................................177
INSPECTION AND ADJUSTMENT ..................179
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
179
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Service After Replacing TCM
and Transaxle Assembly .......................................
179
FUNCTION DIAGNOSIS ...........................181
CVT SYSTEM ...................................................181
System Diagram ...................................................181
Component Parts Location ...................................182
MECHANICAL SYSTEM ..................................183
Cross-Sectional View ............................................183
System Diagram ...................................................184
System Description ...............................................184
Component Parts Location ...................................185
Component Description ........................................186
HYDRAULIC CONTROL SYSTEM ..................187
System Diagram ...................................................187
System Description ...............................................187
Component Parts Location ...................................188
Component Description ........................................189
CONTROL SYSTEM .........................................190
System Diagram ...................................................190
System Description ...............................................190
Component Parts Location ...................................192
Component Description ........................................193
LOCK-UP AND SELECT CONTROL SYSTEM
..
194

TM-5
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P System Diagram ....................................................
194
System Description ...............................................194
Component Parts Location ....................................195
Component Description .........................................196
SHIFT CONTROL SYSTEM .............................197
System Diagram ....................................................197
System Description ...............................................197
Component Parts Location ....................................198
Component Description .........................................199
SHIFT LOCK SYSTEM .....................................200
System Description ...............................................200
Component Parts Location ....................................201
Component Description .........................................201
ON BOARD DIAGNOSTIC (OBD) SYSTEM ....202
Diagnosis Description ...........................................202
DIAGNOSIS SYSTEM (TCM) ...........................204
CONSULT-III Function (TRANSMISSION) ...........204
Diagnostic Tool Function .......................................207
COMPONENT DIAGNOSIS .......................208
U1000 CAN COMM CIRCUIT ...........................208
Description ............................................................208
DTC Logic .............................................................208
Diagnosis Procedure .............................................208
U1010 CONTROL UNIT (CAN) ........................209
Description ............................................................209
DTC Logic .............................................................209
Diagnosis Procedure .............................................209
P0703 STOP LAMP SWITCH ..........................210
Description ............................................................210
DTC Logic .............................................................210
Diagnosis Procedure .............................................210
Component Inspection (Stop Lamp Switch) ..........211
P0705 PARK/NEUTRAL POSITION SWITCH ..213
Description ............................................................213
DTC Logic .............................................................213
Diagnosis Procedure .............................................213
Component Inspection (Park/Neutral Position
Switch) ..................................................................
214
P0710 CVT FLUID TEMPERATURE SENSOR
..
216
Description ............................................................216
DTC Logic .............................................................216
Diagnosis Procedure .............................................216
Component Inspection (CVT Fluid Temperature
Sensor) ..................................................................
217
P0715 INPUT SPEED SENSOR (PRI SPEED
SENSOR) ..........................................................
218
Description ............................................................218
DTC Logic .............................................................218
Diagnosis Procedure .............................................218
P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) ...........................
222
Description .............................................................222
DTC Logic ..............................................................222
Diagnosis Procedure .............................................222
P0725 ENGINE SPEED SIGNAL ....................226
Description .............................................................226
DTC Logic ..............................................................226
Diagnosis Procedure .............................................226
P0730 BELT DAMAGE ...................................228
Description .............................................................228
DTC Logic ..............................................................228
Diagnosis Procedure .............................................228
P0740 TORQUE CONVERTER CLUTCH SO-
LENOID VALVE ..............................................
230
Description .............................................................230
DTC Logic ..............................................................230
Diagnosis Procedure .............................................230
Component Inspection (Torque Converter Clutch
Solenoid Valve) .....................................................
231
P0744 A/T TCC S/V FUNCTION (LOCK -UP) .232
Description .............................................................232
DTC Logic ..............................................................232
Diagnosis Procedure .............................................232
Component Inspection (Torque Converter Clutch
Solenoid Valve) .....................................................
233
Component Inspection (Lock-up Select Solenoid
Valve) ....................................................................
233
P0745 LINE PRESSURE SOLENOID VALVE .234
Description .............................................................234
DTC Logic ..............................................................234
Diagnosis Procedure .............................................234
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] .......
235
P0746 PRESSURE CONTROL SOLENOID A
PERFORMANCE (LINE PRESSURE SOLE-
NOID VALVE) ..................................................
236
Description .............................................................236
DTC Logic ..............................................................236
Diagnosis Procedure .............................................236
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] .......
237
P0776 PRESSURE CONTROL SOLENOID B
PERFORMANCE (SEC PRESSURE SOLE-
NOID VALVE) ..................................................
238
Description .............................................................238
DTC Logic ..............................................................238
Diagnosis Procedure .............................................238
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] .......
239
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] ...................................................................
239

TM-6
P0778 PRESSURE CONTROL SOLENOID B
ELECTRICAL (SEC PRESSURE SOLENOID
VALVE) ............................................................
240
Description .............................................................240
DTC Logic ..............................................................240
Diagnosis Procedure .............................................240
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] ...................................................................
241
P0840 TRANSMISSION FLUID PRESSURE
SENSOR A (SEC PRESSURE SENSOR) .......
242
Description .............................................................242
DTC Logic ..............................................................242
Diagnosis Procedure .............................................242
P0841 PRESSURE SENSOR FUNCTION ......245
Description .............................................................245
DTC Logic ..............................................................245
Diagnosis Procedure .............................................245
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] .......
246
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] ...................................................................
246
P0868 SECONDARY PRESSURE DOWN ......247
Description .............................................................247
DTC Logic ..............................................................247
Diagnosis Procedure .............................................247
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] .......
248
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] ...................................................................
248
P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) ..........................................
249
Description .............................................................249
DTC Logic ..............................................................249
Diagnosis Procedure .............................................249
P1705 THROTTLE POSITION SENSOR ........252
Description .............................................................252
DTC Logic ..............................................................252
Diagnosis Procedure .............................................252
P1722 ESTM VEHICLE SPEED SIGNAL ........253
Description .............................................................253
DTC Logic ..............................................................253
Diagnosis Procedure .............................................253
P1723 CVT SPEED SENSOR FUNCTION ......255
Description .............................................................255
DTC Logic ..............................................................255
Diagnosis Procedure .............................................255
P1726 ELECTRIC THROTTLE CONTROL
SYSTEM ...........................................................
257
Description .............................................................257
DTC Logic .............................................................257
Diagnosis Procedure .............................................257
P1740 LOCK-UP SELECT SOLENOID
VALVE ..............................................................
258
Description ............................................................258
DTC Logic .............................................................258
Diagnosis Procedure .............................................258
Component Inspection (Lock-up Select Solenoid
Valve) ....................................................................
259
P1745 LINE PRESSURE CONTROL ...............260
Description ............................................................260
DTC Logic .............................................................260
Diagnosis Procedure .............................................260
P1777 STEP MOTOR .......................................261
Description ............................................................261
DTC Logic .............................................................261
Diagnosis Procedure .............................................261
Component Inspection (Step Motor) .....................263
P1778 STEP MOTOR - FUNCTION .................264
Description ............................................................264
DTC Logic .............................................................264
Diagnosis Procedure .............................................264
SHIFT POSITION INDICATOR CIRCUIT .........266
Description ............................................................266
Component Function Check .................................266
Diagnosis Procedure .............................................266
SHIFT LOCK SYSTEM .....................................267
Description ............................................................267
Wiring Diagram - CVT SHIFT LOCK SYSTEM - ...267
Component Function Check .................................269
Diagnosis Procedure .............................................270
Component Inspection (Stop Lamp Switch) ..........271
SPORT MODE SWITCH ...................................272
Description ............................................................272
Component Function Check .................................272
Diagnosis Procedure .............................................272
ECU DIAGNOSIS ......................................275
TCM ..................................................................275
Reference Value ...................................................275
Wiring Diagram - CVT CONTROL SYSTEM - ......279
Fail-safe ................................................................283
DTC Inspection Priority Chart ...............................284
DTC Index .............................................................284
SYMPTOM DIAGNOSIS ...........................286
SYSTEM SYMPTOM ........................................286
Symptom Table .....................................................286
PRECAUTION ...........................................297
PRECAUTIONS ................................................297

DIAGNOSIS AND REPAIR WORK FLOW
TM-9
< BASIC INSPECTION >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work FlowINFOID:0000000003848914
INTRODUCTION
The TCM receives signals from the vehicle speed sensor and PNP switch. Then it provides shift control or
lock-up control via CVT solenoid valves.
The TCM also communicates with the ECM by means of signals
sent from sensing elements used with the OBD-related parts of the
CVT system for malfunction-diagnostic purposes. The TCM is capa-
ble of diagnosing malfunctioning parts while the ECM can store mal-
functions in its memory.
Input and output signals must always be correct and stable in the
operation of the CVT system. The CVT system must be in good
operating condition and be free of valve seizure, solenoid valve mal-
function, etc.
It is much more difficult to diagnose a malfunction that occurs inter-
mittently rather than continuously. Most intermittent malfunctions are
caused by poor electric connections or improper wiring. In this case,
careful checking of suspected circuits may help prevent the replace-
ment of good parts.
A visual check only may not find the cause of the malfunctions. A
road test with CONSULT-III (or GST) or a circuit tester connected
should be performed. Follow the “DETAILED FLOW”.
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such malfunctions, espe-
cially intermittent ones. Find out what symptoms are present and
under what conditions they occur. A “Diagnostic Work Sheet” as
shown on the example (Refer to TM-10
) should be used.
Start your diagnosis by looking for “conventional” malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
Also check related Service Bulletins.
DETAILED FLOW
1.COLLECT THE INFORMATION FROM THE CUSTOMER
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred) using the diagnosis work sheet. Refer to TM-10, "
Diagnostic Work Sheet".
>> GO TO 2.
2.CHECK SYMPTOM 1
Check the following items based on the information obtained from the customer.
 Fail-safe. Refer to TM-120, "
Fail-safe".
 CVT fluid inspection. Refer to TM-142, "
Inspection".
 Line pressure test. Refer to TM-146, "
Inspection and Judgment".
SAT631IB
SAT632I
SEF234G

DIAGNOSIS AND REPAIR WORK FLOW
TM-11
< BASIC INSPECTION >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
DIAGNOSTIC WORK SHEET
Symptomso Vehicle does not move. (o Any positiono Particular position)
o No shift
o Lock-up malfunction
o Shift shock or slip (o N → Do N → Ro Lock-upo Any drive position)
o Noise or vibration
o No pattern select
o Others
()
Malfunction Indicator (MI)o Continuously lito Not lit
1o Read the item on cautions concerning fail-safe and understand the customer's complaint.TM-120
2o CVT fluid inspection, stall test and line pressure test
o CVT fluid inspection
TM-142
o Leak (Repair leak location.)
o Sta te
o Amount
o Stall test
TM-144
TM-146
o Torque converter one-way clutch
o Reverse brake
o Forward clutch
o Ste el be lto Engine
o Line pressure low
o Primary pulley
o Secondary pulley
o Line pressure inspection - Suspected part:
3o Perform self-diagnosis.
TM-37
Enter checks for detected items.
4o Perform road test.TM-148
4-1. Check before engine is started TM-148
4-2. Check at idleTM-149
4-3. Cruise testTM-150
o Check malfunction phenomena to repair or replace malfunctioning part after completing all road tests.TM-123
5o Drive vehicle to check that the malfunction phenomenon has been resolved.
6o Erase the results of the self-diagnosis from the TCM and the ECM.