steering NISSAN TEANA 2008 Manual Online

AV-372
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003765766
RELATED TO VEHICLE INFORMATION
RELATED TO REAR VIEW MONITOR
RELATED TO RGB IMAGE
Symptoms Check items Possible malfunction location / Action to take
Multifunction switch and preset
switch operation does not work. All switches cannot be operated.
 “Multi AV” is displayed on system se-
lection display when the CONSULT-
III is initialized.Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Function (MULTI AV)".
 All switches cannot be operated
 “Multi AV” is not displayed on system
selection screen when the CON-
SULT-III is initialized.AV control unit power supply and ground circuits mal-
function.
Refer to AV- 2 3 6 , "
AV CONTROL UNIT : Diagnosis Pro-
cedure".
Only specified switch cannot be operat-
edMultifunction switch or preset switch malfunction.
Replace multifunction switch or preset switch.
For multifunction switch, refer to AV- 3 7 8 , "
Removal and
Installation".
For preset switch, Refer to AV- 3 8 9 , "
Removal and Instal-
lation".
Fuel economy display, vehicle set-
ting operation is abnormalThere is malfunction in the CONSULT-
III self-diagnosis resultPerform detected DTC self-diagnosis.
There is no malfunction in the self-diag-
nosis resultsIgnition signal. Refer to AV- 2 3 6 , "
AV CONTROL UNIT :
Diagnosis Procedure".
Symptoms Check itemsProbable malfunction location / Action
to take
It cannot be switched to rear view
monitor even when the selector le-
ver is in the reverse position. There is malfunction in the CONSULT-III self-diagno-
sis result.Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Func-
tion (MULTI AV)".
There is not malfunction in the CONSULT-III self-diag-
nosis result.Reverse signal circuit malfunction.(AV
control unit)
Camera image is not shown. DVD and AUX images are normal.  Rear view camera power supply cir-
cuit malfunction.
Refer to AV- 2 5 0 , "
Diagnosis Proce-
dure".
 Camera image signal circuit malfunc-
tion.
Refer to AV- 2 5 1 , "
Diagnosis Proce-
dure".
Possible route line is indicated ab-
normally when camera image is dis-
played.The “Steer. Angle Sensor” is not turned ON at “Con-
nection Confirmation” of “Camera Cont.”Steering angle sensor signal circuits.
Refer to AV- 2 5 3 , "
Diagnosis Proce-
dure".
Camera image is rolling. AUX image is rolling Horizontal synchronizing (HP) signal
circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 2 4 6 , "
Diagnosis Proce-
dure".
 Vertical synchronizing (VP) signal cir-
cuit malfunction between AV control
unit and display unit.
Refer to AV- 2 4 7 , "
Diagnosis Proce-
dure".

AV
MULTI AV SYSTEM SYMPTOMS
AV-373
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO STEERING SWITCH
Trouble diagnosis chart by symptom
Symptoms Check items Possible malfunction location / Action to take
RGB image is not shown. All RGB images are not shown.
 Composite images are not dis-
played.(camera and DVD and AUX im-
age)  Display unit power supply and ground circuit malfunc-
tion.
Refer to AV- 2 3 6 , "
DISPLAY UNIT : Diagnosis Proce-
dure".
 Communication circuit malfunction between AV control
unit and display unit.
Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Function (MULTI AV)".
 All RGB images are not shown.
 Camera image is normal.
 DVD and AUX images are not dis-
played. Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Function (MULTI AV)".
 All RGB images are not shown.
 “Multi AV” is not displayed on system
selection screen when the CONSULT-
III is initialized.AV control unit power supply and ground circuit malfunc-
tion.
Refer to AV-236, "
AV CONTROL UNIT : Diagnosis Proce-
dure".
 All RGB images are not shown.
 Composite images are normal. (cam-
era and DVD and AUX image) RGB area (YS) signal circuit malfunction.
Refer to AV- 2 4 5 , "
Diagnosis Procedure".
Color of RGB image is not
proper. (All RGB image)Light blue (Cyan) tint.RGB signal (R: red) circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 2 4 1 , "
Diagnosis Procedure".
Purple (Magenta) tint.RGB signal (G: green) circuit malfunction between AV
control unit and display unit.
Refer to AV- 2 4 2 , "
Diagnosis Procedure".
Screen looks yellowish.RGB signal (B: blue) circuit malfunction between AV con-
trol unit and display unit.
Refer AV- 2 4 3 , "
Diagnosis Procedure".
RGB screen is rolling. All RGB screen is rolling.RGB synchronizing signal circuit malfunction between AV
control unit and display unit.
Refer to AV- 2 4 4 , "
Diagnosis Procedure".
Symptoms Check items Possible malfunction location / Action to take
The CD cannot be removed. —Disk eject signal circuit.
Refer to AV- 2 4 9 , "
Diagnosis Procedure".
Audio sound is not heard.No sound from all speakers. Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Function (MULTI AV)"
 BOSE amp. power supply and ground circuits malfunc-
tion. Refer to AV- 2 3 8 , "
BOSE AMP. : Diagnosis Proce-
dure".
 No sound from all speakers.
 It dose not change to "DVD" mode.
Perform CONSULT-III self-diagnosis.
Refer to AV- 2 11 , "
CONSULT-III Function (MULTI AV)"Sound is not heard only from the specific
places.
AM/FM radio is not received. Other audio sounds are normal. Antenna amp. ON signal circuit.
Symptoms Probable malfunction location
None of the steering switch operations work.Steering switch signal GND circuit. Refer to AV- 2 5 9 , "
Diagnosis Proce-
dure".
Only specified switch cannot be operated Replace steering switch. Refer to AV- 3 9 6 , "
Removal and Installation".

AV-374
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
RELATED TO DVD
RELATED TO AUXILIARY INPUT
NOTE:
Check that there is no malfunction of AUX equipment main body before performing a diagnosis.
RELATED TO REAR CONTROL SWITCH
Steering switch's “SOURCE”, “MENU UP”, “MENU DOWN”
switches do not work.Steering switch signal A circuit. Refer to AV- 2 5 5 , "Diagnosis Procedure".
Steering switch's “VOL UP”, “VOL DOWN” switches do not
work.Steering switch signal B circuit. Refer to AV- 2 5 7 , "
Diagnosis Procedure". Symptoms Probable malfunction location
Symptoms Check items Probable malfunction location
DVD image is not displayed Displayed in black and nothing displayed. Composite image signal circuit malfunc-
tion between AV control unit and display
unit.
Refer to AV- 2 5 2 , "
Diagnosis Procedure"
 RGB area synchronizing (YS) signal cir-
cuit malfunction between AV control unit
and display unit.
Refer to AV- 2 4 5 , "
Diagnosis Procedure"
 Horizontal synchronizing (HP) signal cir-
cuit malfunction between AV control unit
and display unit.
Refer to AV- 2 4 6 , "
Diagnosis Procedure".
 Vertical synchronizing (VP) signal circuit
malfunction between AV control unit and
display unit.
Refer to AV- 2 4 7 , "
Diagnosis Procedure".
It dose not change to "DVD" mode.LED lump of DVD player is not turned on.DVD player power supply and ground cir-
cuits malfunction.
Refer to AV- 2 3 9 , "
DVD PLAYER : Diagno-
sis Procedure".
LED lump of DVD player is not turned on.Perform CONSULT-III self-diagnosis. Refer
to AV- 2 11 , "
CONSULT-III Function (MULTI
AV )"
Symptoms Check items Probable malfunction location
No voice sound is heard when
AUX mode is selected.Voice sound is heard when other modes
are selected.AUX sound signal circuits malfunction between auxiliary
input jacks and AV control unit.
AUX image is not displayed Displayed in black and nothing can be dis-
played RGB area synchronizing (YS) signal circuit malfunc-
tion between AV control unit and display unit.
Refer to AV- 2 4 5 , "
Diagnosis Procedure".
 Horizontal synchronizing (HP) signal circuit malfunc-
tion between AV control unit and display unit.
Refer to AV- 2 4 6 , "
Diagnosis Procedure".
 Vertical synchronizing (VP) signal circuit malfunction
between AV control unit and display unit.
Refer to AV- 2 4 7 , "
Diagnosis Procedure".
 DVD image is normal.
 Menu image is normal.AUX image signal circuit malfunction between DVD play-
er and auxiliary input jacks.
Refer to AV- 2 4 8 , "
Diagnosis Procedure".
Symptoms Check items Probable malfunction location
None of the rear control switch operations
work.—Perform CONSULT-III self-diagnosis. Refer
to AV- 2 11 , "
CONSULT-III Function (MULTI
AV )".

AV-396
< ON-VEHICLE REPAIR >[BOSE AUDIO WITHOUT NAVIGATION]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Exploded ViewINFOID:0000000003838369
REMOVAL
Refer to SR-9, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003838370
REMOVAL
1. Remove spiral cable.
2. Remove steering angle sensor mounting screws.
3. Remove steering angle sensor.
INSTALLATION
Installation is the reverse order of removal.
JSNIA0135ZZ
1. Spiral cable
2. Steering angle sensor

AV-400
< BASIC INSPECTION >[BOSE AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003778340
WITH REAR VIEW MONITOR
Always correct the center position of the predicted course line after disconnecting the battery negative termi-
nal.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003778341
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-400, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003778342
When camera control unit is replaced, the center position of predicted course line shall be corrected.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003778343
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-400, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000003778344
Adjust the center position of the predicted course line of the rear view monitor if it is shifted.
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special Repair
Requirement
INFOID:0000000003778345
1.STEERING OPERATION
Steer the steering wheel to the leftmost and rightmost ends.
>> GO TO 2.
2.DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END

AV-402
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
 AV control unit is connected by CAN communication, and it receives data signal from ECM, combination
meter. It computes and displays fuel economy information value with the obtained information. Transmitting/
receiving of data signal is performed by BCM. Also, it transmits the required signal of vehicle setting and
receives the response signal.
 AV control unit is connected with display unit and serial communication, and it transmits the required signal
of display and display control and receives the response signal from display unit.
NOTE:
AV control unit can perform CONSULT-III self-operating function and on board self-diagnosis.
 CONSULT-III self diagnosis: Refer to AV-434, "
CONSULT-III Function (MULTI AV)".
 On board self diagnosis: Refer to AV-419, "
Diagnosis Description".
HANDS-FREE PHONE SYSTEM
 Hands-free communication can be operated by connecting using Bluetooth™ communication with cellular
phone.
 Operation is performed by display unit (touch panel), multifunction switch or steering switch, and operating
condition is indicated on display unit.
When a call is originated
Spoken voice sound output from the microphone (Mic. Signal) is input to NAVI control unit. NAVI control unit
outputs to cellular phone via TEL antenna with Bluetooth
™ communication as a TEL voice signal. Voice sound
is then heard at the other party.
When receiving a call
Voice sound is input to own cellular phone from the other party. The cellular phone outputs the voice signal to
TEL antenna by establishing Bluetooth
™ communication. The signal from TEL antenna is sent to front speaker
via NAVI control unit, AV control unit, and BOSE amp.
DVD ENTERTAINMENT SYSTEM
 DVD player is connected with AV control unit via AV communication, and controlled by AV control unit.
 DVD image signal is output from DVD player to display unit via AV control unit.
 DVD stereo (2ch) sound signal is output from DVD player to each speaker via AV control unit and BOSE
amp.
 DVD surround (5.1ch) sound signal is output from DVD player to each speaker via BOSE amp.
JSNIA1305GB

AV
MULTI AV SYSTEM
AV-403
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 Operation can be performed with multifunction switch, steering switch and rear control switch. Multifunction
switch and rear control switch transmits operation signal to AV control unit by AV communication.
AUXILIARY INPUT SYSTEM
 Image and sound can be output from an external device by connecting a device with auxiliary input jacks.
 Operation can be performed with multifunction switch, steering switch and rear control switch. Multifunction
switch and rear control switch transmits operation signal to AV control unit by AV communication.
TOUCH PANEL SYSTEM
Each operation of multi AV system can be performed by directly touching a display.
JSNIA1299GB
JSNIA1301GB
JSNIA1308GB

AV
MULTI AV SYSTEM
AV-405
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003765830
13. Camera control unit 14. TEL antenna 15. Rear squawker RH
16. Antenna amp. 17. GPS antenna 18. Rear door speaker RH
19. Front door speaker RH 20. Steering angle sensor 21. Steering switch
22. AV control unit 23. Auxiliary input jacks 24. Preset switch
25. DVD player 26. Multifunction switch 27. Display unit
28. Microphone
A. Trunk room upper LH B. Trunk room upper RH C. Trunk room side RH
D. Within rear pillar finisher RH E. Within rear pillar finisher RH F. Within rear parcel shelf finisher
G. Spiral cable part H. In center console I. In grove box
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter. via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 Composite image signal (AUX and DVD images) is input from DVD player.
 Camera image signal is input from camera control unit.
 Composite image (DVD, AUX and camera images) signal is output to display
unit.
 Sound signal (DVD and AUX sounds) is input from the DVD player.
NAVI CONTROL UNIT Map data can be read from the Map DVD-ROM by installing Map DVD-ROM.
 The NAVI control unit sends map data to the AV control unit.
 The NAVI control unit includes the hands-free phone and navigation functions.
 The NAVI control unit transmits navigation and hands-free phone related im-
ages to AV control unit.
 It includes the TEL adapter and Bluetooth
™ function.
Map DVD-ROM A collection of map data.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
 RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
 Composite image (DVD, AUX and camera images) signal is input from AV con-
trol unit.
 Synchronize signal (HP, VP) is output to AV control unit.
 Touch panel function can be operated for each system by touching a display
directly.
BOSE AMP.Inputs sound signal from AV control unit and DVD player, and outputs sound sig-
nal to woofer and each speaker.
WOOFER Outputs sound signal from BOSE amp.
 Outputs low frequency sound.
FRONT SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
REAR SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
CENTER SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).

AV-406
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
MULTIFUNCTION SWITCH Operation panel is equipped with the centralized switch where camera, audio,
DVD and AUX input operations are integrated.
 The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Operation panel is equipped with the centralized switch where audio and air
conditioner operations are integrated.
 The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
 The disk ejection operating signal is performed by wiring harness.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
 Power supply is transmitted to rear view camera.
 AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
 Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
 It receives the power supply from the camera control unit and operates.
STEERING ANGLE SENSOR Sensor signal (steering angle) is transmitted to camera control unit.
MICROPHONE Used for hands-free phone operation.
 Mic. signal is transmitted to NAVI control unit
 Power (Mic. VCC) is supplied from NAVI control unit.
STEERING SWITCH Enables audio operations, etc.
 Steering switch signal (operation signal) is output to AV control unit.
DVD PLAYERIt transmits the playback DVD image signal and DVD sound signal to the AV con-
trol unit.
AUXILIARY INPUT JACKS The image signal of the auxiliary input is output via the DVD player and AV con-
trol unit to the display unit.
 The sound signal of the auxiliary input is output via the DVD player and AV con-
trol unit to the BOSE amp.
 The image signal of the auxiliary input is output via the AV control unit to the
display, and it outputs the sound signal to the AV control unit.
REAR CONTROL SWITCH Enables audio operations, etc.
 The rear control switch is connected via AV communication, and it transmits
the operation signals of the rear control switch.
ANTENNA AMP. Radio signal received by glass antenna is amplified and transmitted to AV con-
trol unit.
 Power (antenna amp ON signal) is supplied from AV control unit.
GPS ANTENNA GPS signal is received and transmitted to NAVI control unit.
TEL ANTENNA TEL voice signal is received and transmitted to NAVI control unit.Part name Description

AV
AUDIO SYSTEM
AV-407
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUDIO SYSTEM
System DiagramINFOID:0000000003765831
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
System DescriptionINFOID:0000000003765832
The audio system is equipped with following function. Each function can be operated with the multifunction
switch, preset switch, rear control switch or steering switch. It indicates the operation status of AUDIO to the
display unit.
FUNCTION DESCRIPTION
Operating Signal
Operation of the audio system can be performed via the multifunction switch, preset switch, rear control switch
or steering switch.
 Operating signal is transmitted to AV control unit via AV communication when it is operated by multifunction
switch, preset switch or rear control switch. The CD ejection operating signal is performed by hard-wire.
 Operating signal is transmitted to AV control unit with steering switch signal when it is operated by steering
switch.
Screen Display
 The display switching of the screen is performed by the communication signal between the display unit and
the AV control unit.
 The image signal to display operating condition is performed by RGB image signal, RGB area signal and
RGB image synchronizing signal.
AM/FM Radio Mode
 AM/FM radio tuner is built into AV control unit.
 AM/FM radio wave is received by glass antenna, next it is amplified by antenna amp., and finally it is input to
AV control unit. The FM sub antenna is installed on the rear window glass and the AV control unit is
received.
 Sound signal is input to BOSE amp. and BOSE amp. outputs to woofer and each speaker for AV control unit.
CD Mode
 CD function is built into AV control unit.
 AV control unit outputs sound signal to BOSE amp. and BOSE amp. outputs to woofer and each speaker
when CD is inserted to AV control unit.
JSNIA1310GB
Function
AM/FM radio
CD