Ldw NISSAN TEANA 2014 Owners Manual

DAS
HANDLING PRECAUTIONDAS-157
< SYSTEM DESCRIPTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
HANDLING PRECAUTION
Precautions for Blind Spot WarningINFOID:0000000009464811
REAR VIEW CAMERA HANDLING
The rear camera unit “1” for the LDW/BSW sy stems is located above the rear license plate.
To keep the proper operation of the LDW systems and prev ent a system malfunction, be sure to observe the
following:
• Always keep the camera lens clean. Be careful not to damage the nozzle of the automatic washer and
blower.
• Do not attach ”license plate accessories” that reflect light.
• Do not strike or damage the areas around the camera unit.
BLIND SPOT WARNING (BSW)
• BSW system is not a replacement for proper drivi ng procedure and is not designed to prevent contact with
vehicles or objects. When changing lanes, always use the side and rear mirrors and turn and look in the
direction you will move to ensure it is safe to change lanes. Never rely solely on the BSW system.
• The camera unit may not detect properly under the following conditions:
- When towing a trailer.
- When strong light enters the camera unit. (For exampl e, direct sunlight or headlight from the rear.)
- When ambient light changes instantly. (For example, when the vehicle enters or exits a tunnel or passes
under a bridge.)
• Automatic washer and blower may not be able to secu re detection capability when excessive dirt adheres on
the camera lens.
• Excessive noise (e.g. audio system volume, open vehicle window) will interfere with the chime sound, and it
may not be heard.
• The camera unit may not be able to detect when certain objects are present such as:
- Pedestrians, bicycles, animals.
- Several types of vehicles such as motorcycles.
- Oncoming vehicles.
- A vehicle approaching rapidly from behind
- A vehicle which your vehicle overtakes rapidly.
• The camera unit may not be able to detect properly when your vehicle travels beside the middle section of a
vehicle with a long wheelbase (e.g., trailer truck, semi-trailer, tractor).
• The camera unit is designed to ignore most stationary objects, however objects such as guardrails, walls,
foliage and parked vehicles may occasionally be det ected. This is a normal operating condition.
• The camera unit may detect reflection image of vehicles or roadside objects that are not actually in the
detection zone, especially when the road is wet.
ALOIA0181ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DIAGNOSIS SYSTEM (ITS CONTROL UNIT)DAS-159
< SYSTEM DESCRIPTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
WORK SUPPORT
ACTIVE TEST
CAUTION:
• Never perform “Active Test” while driving the vehicle.
• The “Active Test” cannot be performed when th e following systems warning indicators are illumi-
nated:
- Lane Departure Warning indicator
- Blind Spot Warning indicator
• Place the shift selector to P (park) position, and then perform the test.
BSW ON INDICATOR
ILL
[On/Off] Indicates [On/Off] status of the illumination signal
ITS SW 1
[On/Off] Indicates the state of the warning system switch as seen by the ITS control unit
ITS SW 1 IND
[On/Off] Indicates the state of the warning system switch indicator output
TURN SIGNAL
[Left/N/Right] Indicates [Left/N/Right] status of the turn signal output
ITS SW 2
[ON/OFF/No setting] Indicates the state of the warning system secondary switch as seen by the ITS control unit
ITS SW 2 IND
[ON/OFF/No setting] Indicates the state of the warning system secondary switch indicator output
Monitored item
[Unit] Description
Work support items Description
PREDICTIVE COURSE LINE
DISPLAY Setting whether predictive guide line displays or not
INITIALIZE CAMERA IMAGE
CALIBRATION Start the initialization process of the rear camera
STEERING ANGLE SENSOR
ADJUSTMENT Execute register neutral point of steering angle sensor
CALIBRATING CAMERA IM-
AGE (REAR CAMERA) Displays the various values of the rear camera during the calibration process
REAR WIDE-VIEW FIXED
GUIDE LINE CORRECTION Adjustment the position of fixed guide line on rear wide view
REAR CAMERA ITS Displays and sets camera image calibration values
CAUSE OF LDW CANCEL Displays the information about reason of LDW cancellation
CAUSE OF BSW CANCEL Displays the information about reason of BSW cancellation
Te s t i t e m D e s c r i p t i o n
WASH ACTIVE ON
Activates the washer to clean the lens of rear camera
OFF
LED LH INDICATOR ON
Flashes the left side LED light for ITS system
OFF
LED RH INDICATOR ON
Flashes the right side LED light for ITS system
OFF
AIR ACTIVE ON
Activates the air pump to clean the lens of rear camera
OFF
AIR & WASH ACTIVE ON
Activates the air pump and washer to clean the lens of rear camera
OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-162
< ECU DIAGNOSIS INFORMATION >[BSW]
ITS CONTROL UNIT
TERMINAL LAYOUT
PHYSICAL VALUES
ALOIA0156ZZ
Te r m i n a l N o . (Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
1
(BR) Ground Washer level switch Input Ignition
switch ON When washer fluid is low
(switch closed) 0 V
When washer fluid is not
low (switch open) 12 V
2
(G) Ground Washer signal pump to
camera Input Ignition switch ON 5 V
3
(W) Ground
Washer signal camera
to pump Output Ignition switch ON 5 V
7
(P) Ground CAN -L — — — —
17
(G) Ground SOW LED signal R Output
While
driving LDW/BSW detected 12 V
LDW/BSW is not detected 0 V
20
(G) Ground Battery supply Input — — 12 V
22
(P) Ground Serial ground Output — — 0 V
27
(L) Ground CAN -H — — — —
28
(R) Ground Reverse Input
Ignition
switch ON Shift selector in R (re-
verse) 12 V
Shift selector not in R (re-
verse) 0 V
32
(P) Ground Cancel SW output Input Ignition
switch ON Cancel switch pressed 0 V
Cancel switch not pressed 12 V
33
(BG) Ground LED input Output Ignition
switch ON Warning system is ON 12 V
Warning system is OFF 0 V
37
(W) Ground SOW LED signal L Output While
driving LDW/BSW detected 12 V
LDW/BSW is not detected 0 V
39
(BG) Ground Ignition power supply Input Ignition switch ON Battery Voltage
40
(B) Ground Ground — — — 0 V
50, 53 Ground Shield — — — 0 V
51
(R) Ground RR CAM GND Output
Ignition
switch ON —0 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ITS CONTROL UNITDAS-163
< ECU DIAGNOSIS INFORMATION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
Fail-safeINFOID:0000000009951649
If a malfunction occurs in each system, ITS contro l unit cancels each control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
DTC Inspection Priority ChartINFOID:0000000009951650
If multiple DTCs are detected simultaneously, che ck them one by one depending on the following DTC inspec-
tion priority chart.
52
(W) Ground RR CAM ON Output Ignition switch ON 6 V
66
(B) Ground RR CAM COMP + Input Ignition switch ON
68
(G) Ground RR CAM CONT Input Ignition switch ON 5 V
69
(B) Ground RR CAM COMP + Input Ignition switch ON
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
ALOIA0179ZZ
ALOIA0179ZZ
System Buzzer Warning Indicator lamp Description
Lane Departure Warning (LDW) Low-pitched
tone Lane Departure Warning lamp Cancel
Blind Spot Warning (BSW) High-pitched
tone Blind Spot Warning lamp Cancel
Moving Object Detection (MOD) Low-pitched
tone Warning lamp MOD icon
(on camera screen) Cancel
Priority Detected items (DTC)
1 • U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
2 • U1305: CAMERA IMAGE CALIB
• U1308: CAMERA CONFIG
3 • C1A39: STRG SEN CIR
• U0428: STRG SEN CAN CIR 2
• U111A: REAR CAMERA IMAGE SIGNAL
• U1232: ST ANGLE SEN CALIB
• U1309: PUMP UNIT CURRENT
• U130B: REAR CAMERA COMM ERROR
• U1310: PUMP UNIT CIRCUIT
4 • C1A03: VHCL SPEED SE CIRC
• C1A04: VDC FAIL
• U0122: VDC P-RUN DIAG
• U0416: VDC CHECKSUM DIAG
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-164
< ECU DIAGNOSIS INFORMATION >[BSW]
ITS CONTROL UNIT
DTC Index
INFOID:0000000009951651
NOTE:
• The details of time display are as follows:
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
• IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now
CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunction is detected again in the process.
- If it is over 39, it is fixed to 39 until the self-diagnosis results are erased. Other than CAN communication sy stem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunction is detected again in the process.
- If it is over 49, it is fixed to 49 until the self-diagnosis results are erased.
NOTE:
With the detection of “U1000” some systems do not perform the fail-safe operation.
Systems for fail-safe
• A: Lane Departure Warning (LDW)
• B: Blind Spot Warning (BSW)
• C: Moving Object Detection (MOD)
DTC
CONSULT display Warning lamp Fail-safe
Reference
CONSULT
Lane Departure Warning
Blind Spot Warning
Moving Object Detection
System
C1A03 VHCL SPEED SE CIRC ON ON ON A, B, C DAS-186
C1A04 VDC FAIL ON ON ON A, B, CDAS-187
C1A39 STRG SEN CIR ON ON ON A, B, CDAS-188
NO DTC IS
DETECTED. FURTHER
TESTING
MAY BE RE- QUIRED NO DTC IS DETECTED.
FURTHER TESTING MAY BE REQUIRED ——— — —
U0122 VDC P-RUN DIAG ON ON ON A, B, C DAS-189
U0416 VDC CHECKSUM DIAG ON ON ON A, B, CDAS-190
U0428 STRG SEN CAN CIR 2 ON ON ON A, B, CDAS-191
U1000NOTECAN COMM CIRCUIT ON ON ON A, B, CDAS-192
U1010 CONTROL UNIT (CAN) ON ON ON A, B, C DAS-193
U 111 AREAR CAMERA IMAGE
SIGNAL ON ON ON A, B, C
DAS-194
U1232 ST ANGLE SEN CALIB ON ON ON A, B, C DAS-196
U1305 CAMERA IMAGE CALIB ON ON ON A, B, CDAS-197
U1308 CAMERA CONFIG ON ON ON A, B, CDAS-198
U1309 PUMP UNIT CURRENT ON ON ON A, B, CDAS-199
U130BREAR CAMERA COMM
ERROR ON ON ON A, B, C
DAS-202
U1310 PUMP UNIT CIRCUIT ON ON ON A, B, C DAS-203
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ACTION TESTDAS-179
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
ACTION TEST
DescriptionINFOID:0000000009464821
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
Inspection ProcedureINFOID:0000000009464822
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
1.CHECK BSW SYSTEM SETTING
1. Start the engine.
2. Check that the BSW system setting can be enabl ed/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.ACTION TEST FOR BSW
1. Enable the setting of the BSW system on the vehicle information display.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check the BSW operation according to the following table.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ADDITIONAL SERVICE WHEN REPLACING REAR VIEW CAMERA
DAS-181
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
ADDITIONAL SERVICE WHEN RE PLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464823
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464824
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-182, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-164, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW syst em action test. Refer to DAS-179, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-234
< SYSTEM DESCRIPTION >[MOD]
DIAGNOSIS SYSTEM (ITS CONTROL UNIT)
WORK SUPPORT
ACTIVE TEST
CAUTION:
• Never perform “Active Test” while driving the vehicle.
• The “Active Test” cannot be performed when th e following systems warning indicators are illumi-
nated:
- Lane Departure Warning indicator
- Blind Spot Warning indicator
• Place the shift selector to P (park) position, and then perform the test.
BSW ON INDICATOR
ILL
[On/Off] Indicates [On/Off] status of the illumination signal
ITS SW 1
[On/Off] Indicates the state of the warning system switch as seen by the ITS control unit
ITS SW 1 IND
[On/Off] Indicates the state of the warning system switch indicator output
TURN SIGNAL
[Left/N/Right] Indicates [Left/N/Right] status of the turn signal output
ITS SW 2
[ON/OFF/No setting] Indicates the state of the warning system secondary switch as seen by the ITS control unit
ITS SW 2 IND
[ON/OFF/No setting] Indicates the state of the warning system secondary switch indicator output
Monitored item
[Unit] Description
Work support items Description
PREDICTIVE COURSE LINE
DISPLAY Setting whether predictive guide line displays or not
INITIALIZE CAMERA IMAGE
CALIBRATION Start the initialization process of the rear camera
STEERING ANGLE SENSOR
ADJUSTMENT Execute register neutral point of steering angle sensor
CALIBRATING CAMERA IM-
AGE (REAR CAMERA) Displays the various values of the rear camera during the calibration process
REAR WIDE-VIEW FIXED
GUIDE LINE CORRECTION Adjustment the position of fixed guide line on rear wide view
REAR CAMERA ITS Displays and sets camera image calibration values
CAUSE OF LDW CANCEL Displays the information about reason of LDW cancellation
CAUSE OF BSW CANCEL Displays the information about reason of BSW cancellation
Te s t i t e m D e s c r i p t i o n
WASH ACTIVE ON
Activates the washer to clean the lens of rear camera
OFF
LED LH INDICATOR ON
Flashes the left side LED light for ITS system
OFF
LED RH INDICATOR ON
Flashes the right side LED light for ITS system
OFF
AIR ACTIVE ON
Activates the air pump to clean the lens of rear camera
OFF
AIR & WASH ACTIVE ON
Activates the air pump and washer to clean the lens of rear camera
OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ITS CONTROL UNITDAS-237
< ECU DIAGNOSIS INFORMATION > [MOD]
C
D E
F
G H
I
J
K L
M B
N P
A
TERMINAL LAYOUT
PHYSICAL VALUES
ALOIA0156ZZ
Te r m i n a l N o . (Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
1
(BR) Ground Washer level switch Input Ignition
switch ON When washer fluid is low
(switch closed) 0 V
When washer fluid is not
low (switch open) 12 V
2
(G) Ground Washer signal pump to
camera Input Ignition switch ON 5 V
3
(W) Ground
Washer signal camera
to pump Output Ignition switch ON 5 V
7
(P) Ground CAN -L — — — —
17
(G) Ground SOW LED signal R Output
While
driving LDW/BSW detected 12 V
LDW/BSW is not detected 0 V
20
(G) Ground Battery supply Input — — 12 V
22
(P) Ground Serial ground Output — — 0 V
27
(L) Ground CAN -H — — — —
28
(R) Ground Reverse Input
Ignition
switch ON Shift selector in R (re-
verse) 12 V
Shift selector not in R (re-
verse) 0 V
32
(P) Ground Cancel SW output Input Ignition
switch ON Cancel switch pressed 0 V
Cancel switch not pressed 12 V
33
(BG) Ground LED input Output Ignition
switch ON Warning system is ON 12 V
Warning system is OFF 0 V
37
(W) Ground SOW LED signal L Output While
driving LDW/BSW detected 12 V
LDW/BSW is not detected 0 V
39
(BG) Ground Ignition power supply Input Ignition switch ON Battery Voltage
40
(B) Ground Ground — — — 0 V
50, 53 Ground Shield — — — 0 V
51
(R) Ground RR CAM GND Output
Ignition
switch ON —0 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-238
< ECU DIAGNOSIS INFORMATION >[MOD]
ITS CONTROL UNIT
Fail-safe
INFOID:0000000009951660
If a malfunction occurs in each system, ITS contro l unit cancels each control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
DTC Inspection Priority ChartINFOID:0000000009951661
If multiple DTCs are detected simultaneously, chec k them one by one depending on the following DTC inspec-
tion priority chart.
52
(W) Ground RR CAM ON Output Ignition switch ON 6 V
66
(B) Ground RR CAM COMP + Input Ignition switch ON
68
(G) Ground RR CAM CONT Input Ignition switch ON 5 V
69
(B) Ground RR CAM COMP + Input Ignition switch ON
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
ALOIA0179ZZ
ALOIA0179ZZ
System Buzzer Warning Indicator lamp Description
Lane Departure Warning (LDW) Low-pitched
tone Lane Departure Warning lamp Cancel
Blind Spot Warning (BSW) High-pitched
tone Blind Spot Warning lamp Cancel
Moving Object Detection (MOD) Low-pitched
tone Warning lamp MOD icon
(on camera screen) Cancel
Priority Detected items (DTC)
1 • U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
2 • U1305: CAMERA IMAGE CALIB
• U1308: CAMERA CONFIG
3 • C1A39: STRG SEN CIR
• U0428: STRG SEN CAN CIR 2
• U111A: REAR CAMERA IMAGE SIGNAL
• U1232: ST ANGLE SEN CALIB
• U1309: PUMP UNIT CURRENT
• U130B: REAR CAMERA COMM ERROR
• U1310: PUMP UNIT CIRCUIT
4 • C1A03: VHCL SPEED SE CIRC
• C1A04: VDC FAIL
• U0122: VDC P-RUN DIAG
• U0416: VDC CHECKSUM DIAG
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM