ABS NISSAN TEANA 2014 User Guide

BRAKE PIPINGBR-21
< REMOVAL AND INSTALLATION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
FRONT : Hydraulic PipingINFOID:0000000009463699
Four Channel Hydraulic Circuit
CAUTION:
• All hoses and piping (tubes) must be fr ee from excessive bending, twisting and pulling.
• Make sure there is no interference with other pa rts when turning steering both clockwise and coun-
terclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electri c unit (control unit), refill brake system with new
brake fluid. Then bleed the ai r from the system. Refer to BR-14, "Bleeding Brake System"
.
FRONT : Removal and InstallationINFOID:0000000009463700
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove the wheel and tire using power tool. Refer to WT-55, "Adjustment"
.
2. Drain brake fluid. Refer to BR-14, "Drain and Refill"
.
AWFIA0910ZZ
1. ABS actuator and electric unit
(control unit) 2. Master cylinder 3. Booster
4. Connector A. Union bolt B. Flare nut M12
C. Flare nut M10
Revision: November 20132014 Altima NAM

BR-24
< REMOVAL AND INSTALLATION >
BRAKE PIPING
REAR : Hydraulic Piping
INFOID:0000000009463702
Four Channel Hydraulic Circuit
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other part s when turning steering both clockwise and coun-
terclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the ai r from the system. Refer to BR-14, "Bleeding Brake System"
.
REAR : Removal and InstallationINFOID:0000000009463703
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove wheel and tire using power tool. Refer to WT-55, "Adjustment".
2. Drain brake fluid. Refer to BR-14, "Drain and Refill"
.
AWFIA0910ZZ
1. ABS actuator and electric unit
(control unit) 2. Master cylinder 3. Booster
4. Connector A. Union bolt B. Flare nut M12
C. Flare nut M10
Revision: November 20132014 Altima NAM

BRC-1
BRAKES
C
D E
G H
I
J
K L
M
SECTION BRC
A
B
BRC
N
O P
CONTENTS
BRAKE CONTROL SYSTEM
VDC/TCS/ABS
PRECAUTION ................ ...............................
4
PRECAUTIONS .............................................. .....4
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
4
Precaution for Brake System ....................................4
Precaution for Brake Control .....................................5
Precaution for CAN System ................................ ......5
Precaution for Work ..................................................6
PREPARATION ............................................7
PREPARATION .............................................. .....7
Special Service Tool ........................................... ......7
Commercial Service Tool ..........................................7
SYSTEM DESCRIPTION ..............................8
COMPONENT PARTS ................................... .....8
Component Parts Location .................................. ......8
Component Description .............................................9
ABS Actuator and Electric Unit (Control Unit) ...........9
Wheel Sensor and Sensor Rotor ............................10
Stop Lamp Switch ...................................................10
Steering Angle Sensor ............................................10
Brake Fluid Level Switch .........................................10
Vacuum Sensor .......................................................10
Parking Brake Switch ..............................................11
VDC OFF Switch .....................................................11
SYSTEM .............................................................12
VDC/TCS/ABS ....................................................... ....12
VDC/TCS/ABS : System Diagram ...........................12
VDC/TCS/ABS : System De scription ......................12
VDC/TCS/ABS : VDC Functi on ...............................23
VDC/TCS/ABS : TCS Functi on ...............................25
VDC/TCS/ABS : ABS Function ........................... ....27
VDC/TCS/ABS : EBD Functi on ...............................28
VDC/TCS/ABS : Fail-safe ... .....................................29
DIAGNOSIS SYSTEM [ABS ACTUATOR
AND ELECTRIC UNIT (CONTROL UNIT)] .......
33
CONSULT Function (ABS) .................................. ....33
ECU DIAGNOSIS INFORMATION ..............38
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) .............................................
38
Reference Value .................................................. ....38
Fail-safe ...................................................................41
DTC Inspection Priority Chart ..................................44
DTC Index ...............................................................45
WIRING DIAGRAM ......................................47
BRAKE CONTROL SYSTEM ...........................47
Wiring Diagram .................................................... ....47
BASIC INSPECTION ...................................55
DIAGNOSIS AND REPAIR WORK FLOW .......55
Work Flow ............................................................ ....55
Diagnostic Work Sheet ............................................56
ADDITIONAL SERVICE WHEN REPLACING
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) .............................................
57
Description ........................................................... ....57
ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION ...............................
58
Description ........................................................... ....58
Work Procedure .......................................................58
CONFIGURATION [ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT)] ................
60
Work Procedure ................................................... ....60
CALIBRATION OF DECEL G SENSOR ...........62
Description ...............................................................62
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-2
Work Procedure ......................................................62
DTC/CIRCUIT DIAGNOSIS ...................... ...64
C1101, C1102, C1103, C1104 WHEEL SEN-
SOR ................................................................. ...
64
DTC Logic ............................................................ ...64
Diagnosis Procedure ..............................................64
C1105, C1106, C1107, C1108 WHEEL SEN-
SOR ................................................................. ...
68
DTC Logic ............................................................ ...68
Diagnosis Procedure ..............................................68
C1109 POWER AND GROUND SYSTEM .........70
DTC Logic ............................................................ ...70
Diagnosis Procedure ..............................................70
C1110, C1153, C1170 ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT) .............. ...
72
DTC Logic ............................................................ ...72
Diagnosis Procedure ..............................................72
C1111 PUMP MOTOR .......................................73
DTC Logic ............................................................ ...73
Diagnosis Procedure ..............................................73
C1113, C1145, C1146 YAW RATE/SIDE/DE-
CEL G SENSOR ............................................. ...
75
DTC Logic ............................................................ ...75
Diagnosis Procedure ..............................................75
C1115 ABS SENSOR [ABNORMAL SIGNAL] ...76
DTC Logic ............................................................ ...76
Diagnosis Procedure ..............................................76
C1116 STOP LAMP SWITCH ............................78
DTC Logic ............................................................ ...78
Diagnosis Procedure ..............................................78
C1120, C1122, C1124, C1126 ABS IN VALVE
SYSTEM ............ .............................................. ...
80
DTC Logic ............................................................ ...80
Diagnosis Procedure ..............................................80
C1121, C1123, C1125, C1127 ABS OUT
VALVE SYSTEM ............................................. ...
82
DTC Logic ............................................................ ...82
Diagnosis Procedure ..............................................82
C1130 ENGINE SIGNAL ...................................84
DTC Logic ............................................................ ...84
Diagnosis Procedure ..............................................84
C1140 ACTUATOR RELAY SYSTEM ...............85
DTC Logic ............................................................ ...85
Diagnosis Procedure ..............................................85
C1142 PRESS SENSOR ...................................87
DTC Logic ............................................................ ...87
Diagnosis Procedure ..............................................87
C1143 STEERING ANGLE SENSOR ...............88
DTC Logic ............................................................ ...88
Diagnosis Procedure ...............................................88
C1144 INCOMPLETE STEERING ANGLE
SENSOR ADJUSTMENT ............................... ...
90
DTC Logic ............................................................ ...90
Diagnosis Procedure ...............................................90
C1154 PNP SWITCH .........................................91
Description ........................................................... ...91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
Special Repair Requirement ...................................91
C1155 BR FLUID LEVEL LOW .........................93
DTC Logic ............................................................ ...93
Diagnosis Procedure ...............................................93
Component Inspection ............................................94
C1160 DECEL G SEN SET ...............................95
DTC Logic ............................................................ ...95
Diagnosis Procedure ...............................................95
C1164, C1165, C1166, C1167 CV/SV SYS-
TEM ................................................................. ...
96
DTC Logic ............................................................ ...96
Diagnosis Procedure ...............................................96
C1197 VACUUM SENSOR ............................. ...98
DTC Logic ............................................................ ...98
Diagnosis Procedure ...............................................98
C1198 VACUUM SENSOR ............................. ..100
DTC Logic ............................................................ .100
Diagnosis Procedure .............................................100
C1199 BRAKE BOOSTER ............................. ..102
DTC Logic ............................................................ .102
Diagnosis Procedure .............................................102
C119A VACUUM SENSOR ..............................104
DTC Logic ............................................................ .104
Diagnosis Procedure .............................................104
U1000 CAN COMM CIRCUIT ...........................106
DTC Logic ............................................................ .106
Diagnosis Procedure .............................................106
U1002 SYSTEM COMM (CAN) ........................107
DTC Logic ............................................................ .107
Diagnosis Procedure .............................................107
PARKING BRAKE SWITCH .............................108
Component Function Check ................................ .108
Diagnosis Procedure .............................................108
Component Inspection ..........................................109
VDC OFF SWITCH ...........................................110
Component Function Check ................................ .110
Diagnosis Procedure .............................................110
Component Inspection ..........................................111
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-3
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
ABS WARNING LA MP ................................... ..112
Component Function Check ................................ ..112
Diagnosis Procedure .............................................112
BRAKE WARNING LAMP ............................. ..113
Component Function Check ................................ ..113
Diagnosis Procedure .............................................113
VDC OFF INDICATOR LAMP ..........................114
Description .......................................................... ..114
Component Function Check ..................................114
Diagnosis Procedure .............................................114
SLIP INDICATOR LAMP ..................................115
Component Function Check ................................ ..115
Diagnosis Procedure .............................................115
SYMPTOM DIAGNOSIS ............................116
VDC/TCS/ABS ................................................ ..116
Symptom Table ................................................... ..116
EXCESSIVE ABS FUNCTION OPERATION
FREQUENCY ................................................. ..
117
Diagnosis Procedure ........................................... ..117
UNEXPECTED PEDAL REACTION ................118
Diagnosis Procedure ........................................... ..118
THE BRAKING DISTANCE IS LONG ..............119
Diagnosis Procedure ........................................... ..119
ABS FUNCTION DOES NOT OPERATE .........120
Diagnosis Procedure ........................................... ..120
PEDAL VIBRATION OR ABS OPERATION
SOUND OCCURS .......................................... ..
121
Diagnosis Procedure ........................................... ..121
VEHICLE JERKS DURING VDC/TCS/ABS
CONTROL .......................................................
122
Diagnosis Procedure ........................................... ..122
NORMAL OPERATING CONDITION .............123
Description .............................................................123
REMOVAL AND INSTALLATION .............124
WHEEL SENSOR ............................................124
Exploded View - Front Wheel Sensor .................. ..124
Removal and Installation - Front Wheel Sensor ....124
Exploded View - Rear Wheel Sensor ....................125
Removal and Installation - Rear Wheel Sensor .....125
SENSOR ROTOR ............................................127
Removal and Installation - Front Sensor Rotor .....127
Removal and Installation - Rear Sensor Rotor ......127
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ...........................................
128
Exploded View ..................................................... ..128
Removal and Installation .......................................128
VDC OFF SWITCH ..........................................130
Removal and Installation .......................................130
YAW RATE/SIDE/DECEL G SENSOR ...........131
Removal and Installation .......................................131
STEERING ANGLE SENSOR .........................132
Exploded View .......................................................132
Removal and Installation .......................................132
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-4
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951721
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Brake SystemINFOID:0000000009463735
WARNING:
Clean any dust from the front brake and rear br ake using a vacuum dust collector. Do not blow by
compressed air.
• Brake fluid use refer to BR-8, "Inspection"
.
• Do not reuse drained brake fluid.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface.
• Always confirm the specified tightening torque when installing the brake pipes.
• After pressing the brake pedal more deeply or harder t han normal driving, such as air bleeding, check each
item of brake pedal. Adjust brake pedal if it is outside the standard value.
• Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and cause
improper operation.
• Always loosen the brake tube flar e nut with a flare nut wrench.
• Tighten the brake tube flare nut to the specified torque with a crow-
foot (A) and torque wrench (B).
• Always connect the battery terminal when moving the vehicle.
• Turn the ignition switch OFF and disconnect the ABS actuator and
electric unit (control unit) harness connector or the battery negative
terminal before performing the work.
• Check that no brake fluid leakage is present after replacing the parts.
JPFIA0001ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PRECAUTIONSBRC-5
< PRECAUTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Precaution for Brake ControlINFOID:0000000009463736
• During ABS operation, the brake pedal may vibrate lightly and a mechanical noise may be heard. This is normal.
• Just after starting vehicle, the brake pedal may vibrate or a motor operating noise may be heard from engine
compartment. This is a normal status of operation check.
• Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel, or
snow-covered (fresh, deep snow) roads.
• When an error is indicated by ABS or another warning lamp, collect all necessary information from customer
(what symptoms are present under what conditions) and check for simple causes before starting diagnosis.
Besides electrical system inspection, check boos ter operation, brake fluid level, and fluid leaks.
• If incorrect tire sizes or types are installed on the vehicle or brake pads are not Genuine NISSAN parts, stop-
ping distance or steering stability may deteriorate.
• If there is a radio, antenna or related wiring near control module, ABS function may have a malfunction or
error.
• If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness pinches, open circuits or improper wiring.
• If the following components are replaced with non-genuine components or modified, the VDC OFF indicator
lamp and SLIP indicator lamp may turn on or the VDC system may not operate properly. Components
related to suspension (shock absorbers, struts, springs , bushings, etc.), tires, wheels (exclude specified
size), components related to brake system (pads, roto rs, calipers, etc.), components related to engine (muf-
fler, ECM, etc.), components related to body reinforcement (roll bar, tower bar, etc.).
• Driving with broken or excessively worn suspensi on components, tires or brake system components may
cause the VDC OFF indicator lamp and the SLIP indicator lamp to turn on, and the VDC system may not
operate properly.
• When the TCS or VDC is activated by sudden acceleration or sudden turn, some noise may occur. The
noise is a result of the normal operation of the TCS and VDC.
• When driving on roads which have extreme slopes (such as mountainous roads) or high banks (such as sharp curves on a freeway), the VDC may not operate no rmally, or the VDC warning lamp and the SLIP indi-
cator lamp may turn on. This is not a problem if normal operation can be resumed after restarting the engine.
• Sudden turns (such as spin turns, acceleration turns), drifting, etc. with VDC turned off may cause the yaw rate/side/decel G sensor to indicate a problem. This is not a problem if normal operation can be resumed
after restarting the engine.
Precaution for CAN SystemINFOID:0000000009463737
• Do not apply voltage of 7.0V or higher to terminal to be measured.
• Maximum open terminal voltage of tester in use must be less than 7.0V.
• Before checking harnesses, turn ignition switch OFF and disconnect battery negative cable.
• Area to be repaired must be soldered and wrapped with tape. Make sure that fraying of twisted wire is within 110 mm (4.33 in).
PKIA0306E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-6
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
• Do not make a bypass connection to repaired area. (If the circuit is
bypassed, characteristics of twisted wire will be lost.)
Precaution for WorkINFOID:0000000009463738
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PKIA0307E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PREPARATIONBRC-7
< PREPARATION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
PREPARATION
PREPARATION
Special Service ToolINFOID:0000000009463739
The actual shapes of the tools may differ from those illustrated here.
Commercial Service ToolINFOID:0000000009463740
Tool number
(TechMate No.)
Tool name Description
—
(J-45741)
ABS active wheel sensor tester Checking operation of ABS active wheel sen-
sor
WFIA0101E
Tool name Description
Power tool Loosening nuts, screws and bolts
PIIB1407E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BRC-8
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000009463741
1. IPDM E/R 2. Fuse, fusible link and relay box
(stop lamp relay)3. ABS actuator and el
ectric unit (con-
trol unit)
4. Brake fluid level switch 5. Vacuum sensor (attached to lower side of brake booster)6. Front wheel sensor LH (RH similar)
ALFIA0301ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM