trunk release NISSAN TEANA 2014 User Guide

TRUNK LID OPENER SWITCHDLK-123
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
YES >> GO TO 3
NO >> Repair harness or connector.
3.CHECK TRUNK LID OPENER SWITCH GROUND CIRCUIT
Check continuity between trunk lid opener switch connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK TRUNK LID OPENER SWITCH
Refer to DLK-123, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace trunk lid opener switch.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> Inspection End.
Component InspectionINFOID:0000000009461856
1.CHECK TRUNK LID OPENER SWITCH
1. Turn ignition switch OFF.
2. Disconnect trunk lid opener switch connector.
3. Check continuity between trunk lid opener switch connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace trunk lid opener switch.
Trunk lid opener switch Terminal GroundContinuity
M75 2 Yes
Te r m i n a l Condition Continuity
Trunk lid opener switch
12 ON (press and hold) Yes
OFF (release) No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-126
< DTC/CIRCUIT DIAGNOSIS >
TRUNK LAMP SWITCH
TRUNK LAMP SWITCH
DescriptionINFOID:0000000009461861
Detects trunk open/close condition.
Component Function CheckINFOID:0000000009461862
1.CHECK FUNCTION
With CONSULT
Check TRNK/HAT MNTR in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES >> Trunk lamp switch is OK.
NO >> Refer to DLK-126, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461863
Regarding Wiring Diagram information, refer to DLK-51, "Wiring Diagram".
1.CHECK TRUNK LAMP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> GO TO 2
2.CHECK TRUNK LAMP SWITCH CIRCUIT
1. Disconnect BCM and trunk lamp switch and trunk release solenoid connectors.
2. Check continuity between BCM connector and trunk la mp switch and trunk release solenoid connector.
3. Check continuity between BCM connector and ground.
Monitor item Condition
TRNK/HAT MNTR OPEN : ON
CLOSE : OFF
Te r m i n a l s Trunk
condition Voltage (V)
(Approx.)
(+)
(–)
BCM
connector Te r m i n a l
M19 97 Ground OPEN 0
CLOSE
JPMIA0011GB
BCM connector Terminal Trunk lamp switch and
trunk release solenoid connector Terminal Continuity
M19 97 B28 1 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TRUNK LAMP SWITCHDLK-127
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between BCM and trunk lamp switch and trunk release solenoid.
3.CHECK TRUNK LAMP SWITCH GROUND CIRCUIT
Check continuity between trunk lid lock assembly connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace trunk lamp switch and trunk release solenoid ground circuit.
4.CHECK BCM OUTPUT SIGNAL
1. Insure trunk remains closed during this step.
2. Connect BCM connector.
3. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace BCM. Refer to BCS-80, "Removal and Installation"
.
5.CHECK TRUNK LAMP SWITCH
Refer to DLK-127, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 6
NO >> Replace trunk lamp switch and trunk release solenoid.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> Inspection End.
Component InspectionINFOID:0000000009461864
1.CHECK TRUNK LAMP SWITCH
1. Turn ignition switch OFF.
2. Disconnect trunk lamp switch and trunk release solenoid connector.
3. Check trunk lamp switch.
BCM connector Terminal GroundContinuity
M19 97 No
Trunk lamp switch and trunk release solenoid connector Te r m i n a l
GroundContinuity
B28 2 Yes
Te r m i n a l s Voltage (V)
(Approx.)
(+)
(–)
BCM connector Terminal
M19 97 Ground
JPMIA0011GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-128
< DTC/CIRCUIT DIAGNOSIS >
TRUNK LAMP SWITCH
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace trunk lamp switch and trunk release solenoid.
Te r m i n a l
Trunk condition Continuity
Trunk lamp switch and trunk release
solenoid
12 OPEN Yes
CLOSE No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-132
< DTC/CIRCUIT DIAGNOSIS >
TRUNK OPENER REQUEST SWITCH
TRUNK OPENER REQUEST SWITCH
DescriptionINFOID:0000000009461869
Performs trunk lid open request when it is pressed.
Component Function CheckINFOID:0000000009461870
1.CHECK FUNCTION
With CONSULT
Check trunk opener request switch REQ SW -BD/TR in Data Monitor mode.
Is the inspection result normal?
YES >> Trunk opener request switch is OK.
NO >> Refer to DLK-132, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461871
Regarding Wiring Diagram information, refer to DLK-61, "Wiring Diagram".
1.CHECK TRUNK OPENER REQUEST SWITCH OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> GO TO 2
2.CHECK TRUNK OPENER REQUEST SWITCH CIRCUIT
1. Disconnect BCM and trunk opener request switch connector.
2. Check continuity between BCM connector and trunk opener request switch connector.
3. Check continuity between BCM connector and ground.
Monitor item Condition
REQ SW -BD/TR Trunk opener request switch is pressed : ON
Trunk opener request switch is released : OFF
Te r m i n a l s Trunk lid opener request
switch condition Voltage (V)
(Approx.)
(+)
(–)
BCM connector Terminal
M19 83 Ground Pressed 0
Released
JPMIA0016GB
BCM connector Terminal Trunk opener request switch
connector Terminal Continuity
M19 83 B33 1 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-134
< DTC/CIRCUIT DIAGNOSIS >
TRUNK OPENER REQUEST SWITCH
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace trunk opener request switch.
Te r m i n a l Trunk opener request switch
condition Continuity
Trunk opener request switch
12 Pressed Yes
Released No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-140
< DTC/CIRCUIT DIAGNOSIS >
TRUNK LID OPENER ACTUATOR
TRUNK LID OPENER ACTUATOR
DescriptionINFOID:0000000009461885
Performs trunk lid open with signal from BCM.
Component Function CheckINFOID:0000000009461886
1.CHECK FUNCTION
1. Perform Active Test TRUNK/GLASS HATCH with CONSULT.
2. Touch “OPEN” and check that trunk lid opens.
Is the inspection result normal?
YES >> Trunk lid opener actuator is OK.
NO >> Refer to DLK-140, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461887
Regarding Wiring Diagram information, refer to DLK-77, "Wiring Diagram".
1.CHECK OUTPUT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect trunk lamp switch and trunk release solenoid connector.
3. Check voltage between trunk lamp switch and trunk release solenoid connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2.CHECK OUTPUT SIGNAL
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> Repair or replace harness.
NO >> GO TO 3
3.CHECK TRUNK LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM.
2. Check continuity between BCM connector and trunk la mp switch and trunk release solenoid connector.
Te r m i n a l s
Condition of
trunk lid opener switch Voltage (V)
(Approx.)
(+)
(–)
Trunk lamp
switch and trunk
release solenoid connector Te r m i n a l
B28 3 Ground OFF → ON 0 → Battery voltage → 0
Te r m i n a l s
Condition of
trunk lid opener switch Voltage (V)
(Approx.)
(+)
(–)
BCM connector Terminal
M19 91 Ground OFF → ON 0 → Battery voltage → 0
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TRUNK LID OPENER ACTUATORDLK-141
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Repair or replace harness.
4.CHECK TRUNK LID OPENER GROUND CIRCUIT
Check continuity between trunk lamp switch and trunk release solenoid connector and ground.
Is the inspection result normal?
YES >> Replace trunk lamp switch and trunk release solenoid.
NO >> Repair or replace harness.
BCM connector Terminal Trunk lamp switch and
trunk release solenoid
connector Terminal Continuity
M19 91 B28 3 Yes
BCM connector Terminal Continuity M19 91 Ground No
Trunk lamp switch and trunk release solenoid connector Terminal Continuity
B28 2 Ground Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-146
< DTC/CIRCUIT DIAGNOSIS >
INTELLIGENT KEY BATTERY AND FUNCTION
INTELLIGENT KEY BATTERY AND FUNCTION
DescriptionINFOID:0000000009461895
The following functions are available when having and carrying the Intelligent Key.
• Door lock/unlock
• Trunk open
Remote control entry function and panic alarm functi on are available when operating the remote buttons.
Component Function CheckINFOID:0000000009461896
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
1.CHECK FUNCTION
With CONSULT
Check remote keyless entry receiver RKE OP E COUN1 in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES >> Intelligent Key is OK.
NO >> Refer to DLK-146, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461897
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
1.CHECK INTELLIGENT KEY FUNCTION
Check Intelligent Key function using Signal Tech II Tool J-50190 or
Remote Keyless Entry Tester J-43241 (shown).
Does the test pass?
YES >> Intelligent Key is OK.
NO >> GO TO 2
2. CHECK INTELLIGENT KEY COMPONENTS
1. Release the lock knob at the back of the In telligent Key and remove the mechanical key.
Monitor item Condition
RKE OPE COUN1 Check that the numerical value is changing while operating with the Intelligent Key.
LEL946A
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-206
< REMOVAL AND INSTALLATION >
TRUNK LID
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded ViewINFOID:0000000009461953
TRUNK LID ASSEMBLY : Removal and InstallationINFOID:0000000009461954
CAUTION:
• Use two people when removing or installing trunk lid assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of trunk lid assembly.
REMOVAL
1. Remove trunk lid finisher (if equipped). Refer to INT-33, "TRUNK LID FINISHER : Removal and Installa-
tion".
1. Trunk lid hinge (LH/RH) 2. Torsion bar (LH/RH) 3. Torsion bar clips
4. Trunk lid finisher (if equipped) 5. Emergency release lever handle 6. Emergency release lever clip
7. Emergency release lever cable 8. Trunk lamp switch and trunk re- lease solenoid9. Trunk lid bumpers
10. License plate finisher 11. Rear spoiler (if equipped) 12. Trunk lid
13. Weatherstrip A. Clip Clip
ALKIA2718ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM