warning light NISSAN TEANA 2014 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 1 of 4801

A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
O
QUICK REFERENCE INDEX
AGENERAL INFORMATIONGIGeneral Information
BENGINEEMEngine Mechanical
LUEngine Lubrication System
COEngine Cooling System
ECEngine Control System
FLFuel System
EXExhaust System
STRStarting System
ACCAccelerator Control System
CHYBRIDHBCHybrid Control System
DTRANSMISSION & DRIVE-LINECLClutch System
TMTransaxle & Transmission
DLNDriveline
FAXFront Axle
RAXRear Axle
ESUSPENSIONFSUFront Suspension
RSURear Suspension
SCSSuspension Control System
WTRoad Wheels & Tires
FBRAKESBRBrake System
PBParking Brake System
BRCBrake Control System
GSTEERINGSTSteering System
STCSteering Control System
HRESTRAINTSSBSeat Belt
SBCSeat Belt Control System
SRSRS Airbag
SRCSRS Airbag Control System
IVENTILATION, HEATER &
AIR CONDITIONERVTLVentilation System
HAHeater & Air Conditioning System
HACHeater & Air Conditioning Control System
JBODY INTERIORINTInterior
IPInstrument Panel
SESeat
ADPAutomatic Drive Positioner
KBODY EXTERIOR, DOORS, ROOF & VEHICLE
SECURITYDLKDoor & Lock
SECSecurity Control System
GWGlass & Window System
PWCPower Window Control System
RFRoof
EXTExterior
BRMBody Repair Manual
LDRIVER CONTROLSMIRMirrors
EXLExterior Lighting System
INLInterior Lighting System
WWWiper & Washer
DEFDefogger
HRNHorn
MELECTRICAL & POWER
CONTROLPWOPower Outlet
BCSBody Control System
LANLAN System
PCSPower Control System
CHGCharging System
PGPower Supply, Ground & Circuit Elements
NDRIVER INFORMATION &
MULTIMEDIAMWIMeter, Warning Lamp & Indicator
WCSWarning Chime System
SNSonar System
AVAudio, Visual & Navigation System
OCRUISE CONTROLCCSCruise Control System
DASDriver Assistance System
PMAINTENANCEMAMaintenance
All rights reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, photo-copying, record-
ing or otherwise, without the
prior written permission of
Nissan North America, Inc.
Edition: August 2013
Revision: November 2013
Pub. No. SM14E00L33U1
Page 22 of 4801
![NISSAN TEANA 2014 Service Manual
BCS
SYSTEMBCS-7
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYSTEM
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM
: System DescriptionINFOID:0000000009461989
OUTLINE
• BCM (body control NISSAN TEANA 2014 Service Manual
BCS
SYSTEMBCS-7
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYSTEM
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM
: System DescriptionINFOID:0000000009461989
OUTLINE
• BCM (body control](/img/5/57390/w960_57390-21.png)
BCS
SYSTEMBCS-7
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYSTEM
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM
: System DescriptionINFOID:0000000009461989
OUTLINE
• BCM (body control module) controls various electric al components. It receives the information required from
CAN communication and the signals received from each switch and sensor.
• BCM has a combination switch reading function for readi ng the status of combination switches (light, turn
signal, wiper and washer) in addition to functions for c ontrolling the operation of various electrical compo-
nents. It also has a signal transmission function for ot her systems, and a power consumption control function
that reduces the power consumpt ion with the ignition switch OFF.
• BCM is equipped with a diagnosis function that operates with CONSULT and allows for various settings to
be changed.
BCM FUNCTION LIST
System Refer to
Combination switch reading system BCS-8, "COMBINATION SWITCH READING SYSTEM : System
Description"
Signal buffer system
BCS-12, "SIGNAL BUFFER SYSTEM : System Description"
Power consumption control systemBCS-12, "POWER CONSUMPTION CONTROL SYSTEM : Sys-tem Description"
Auto light system (if equipped)
EXL-10, "AUTO LIGHT SYSTEM : System Description"
Headlamp system EXL-9, "HEADLAMP SYSTEM : System Description"
Daytime light system (if equipped)EXL-11, "DAYTIME RUNNING LIGHT SYSTEM : System De-scription"
Front fog lamp system (if equipped)
EXL-11, "FRONT FOG LAMP SYSTEM : System Description"
Turn signal and hazard warning lamps systemEXL-12, "TURN SIGNAL AND HAZARD WARNING LAMPS : System Description"
Parking, license plate and tail lamps system
EXL-12, "PARKING, LICENSE PLATE AND TAIL LAMPS : Sys-tem Description"
Exterior lamp battery saver system
EXL-9, "HEADLAMP SYSTEM : System Description"
Interior room lamp battery saver systemINL-7, "System Description"
Interior room lamp control system INL-7, "System Description"
Front wiper and washer system WW-6, "System Description"
Warning chime systemWCS-6, "WARNING CHIME SYSTEM : System Description"
Door lock systemDLK-21, "System Description"
Trunk open systemDLK-41, "System Description"
Nissan vehicle immobilizer system (NVIS)SEC-14, "NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS : System Description"
Vehicle security system
SEC-16, "VEHICLE SECURITY SYSTEM : System Description"
Panic alarm
Rear window defogger system DEF-7, "System Description"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 23 of 4801
![NISSAN TEANA 2014 Service Manual
BCS-8
< SYSTEM DESCRIPTION >[BCM]
SYSTEM
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING
SYSTEM : System DiagramINFOID:0000000009461990
COMBINATION SWITCH READING SY STEM : System Descr NISSAN TEANA 2014 Service Manual
BCS-8
< SYSTEM DESCRIPTION >[BCM]
SYSTEM
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING
SYSTEM : System DiagramINFOID:0000000009461990
COMBINATION SWITCH READING SY STEM : System Descr](/img/5/57390/w960_57390-22.png)
BCS-8
< SYSTEM DESCRIPTION >[BCM]
SYSTEM
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING
SYSTEM : System DiagramINFOID:0000000009461990
COMBINATION SWITCH READING SY STEM : System DescriptionINFOID:0000000009461991
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM has a combination of 5 output terminals (OUTPU T 1 - 5) and 5 input terminals (INPUT 1 - 5) and reads
a maximum of 20 switch states.
COMBINATION SWITCH MATRIX
Intelligent Key system/engine start sys-
tem Door lock function
•
DLK-24, "DOOR LOCK FUNCTIO N : System Description"
(door
request switch) (if equipped)
• DLK-24, "DOOR LOCK FUNCTIO N : System Description"
(In-
telligent Key)
Trunk open function DLK-37, "TRUNK LID OPENER SYS
TEM : System Description"
(Intelligent Key)
Warning function DLK-33, "WARNING FUNCTIO N : System Description"
Key reminder functionDLK-29, "KEY REMINDER FUNCTION : System Description"
Engine start functionSEC-11, "INTELLIGENT KEY SYSTEM/ENGINE START FUNC-TION : System Description"
Power window system
•
PWC-10, "System Description" (LH front only anti-pinch)
• PWC-72, "System Description"
(LH & RH front anti-pinch)
RAP (retained accessory power) system BCS-28, "RETAINED PWR : CONSULT Function (BCM - RE-
TAINED PWR)"
TPMS (tire pressure
monitoring system) WT-9, "System Description"
System Refer to
AWMIA1215GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 32 of 4801
![NISSAN TEANA 2014 Service Manual
BCS
DIAGNOSIS SYSTEM (BCM)BCS-17
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
NACTIVE TEST
INT LAMP
INT LAMP : CONSULT Func
tion (BCM - INT LAMP)INFOID:0000000009462000
CAUTION:
After NISSAN TEANA 2014 Service Manual
BCS
DIAGNOSIS SYSTEM (BCM)BCS-17
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
NACTIVE TEST
INT LAMP
INT LAMP : CONSULT Func
tion (BCM - INT LAMP)INFOID:0000000009462000
CAUTION:
After](/img/5/57390/w960_57390-31.png)
BCS
DIAGNOSIS SYSTEM (BCM)BCS-17
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
NACTIVE TEST
INT LAMP
INT LAMP : CONSULT Func
tion (BCM - INT LAMP)INFOID:0000000009462000
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentiall y causing a discharged battery and a no-start condition.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
NOTE:
TAIL LAMP SW [On/Off] Indicates condition of combination switch.
FR FOG SW [On/Off] Indicates condition of front fog lamp switch.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch. Monitor Item [Unit] Description
Test Item Description
SEAT BELT WARN TEST This test is able to check seat belt warning chime operation [On/Off].
LIGHT WARN ALM This test is able to check light warning chime operation [On/Off].
REVERSE WARNING This test is able to check reverse warning chime operation [On/Off].
ID REGIST WARNING This test is able to check TPMS transmitter ID regist warning chime operation [On/Off].
Monitor Item [Unit] Description
REQ SW -DR [On/Off] Indicates condition of door request switch LH.
REQ SW -AS [On/Off] Indicates condition of door request switch RH.
PUSH -SW [On/Off] Indicates condition of push-button ignition switch.
UNLK SEN -DR [On/Off] Indicates condition of door unlock sensor.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off] Indicates condition of trunk switch.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off] Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off] Indicates condition of lo ck signal from door key cylinder switch.
KEY CYL UN-SW [On/Off] Indicates condition of un lock signal from door key cylinder switch.
TRNK/HAT MNTR [On/Off] Indicates condition of trunk room lamp switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
Test Item Description
INT LAMP This test is able to check interior room lamp operation [On/Off].
STEP LAMP TEST This test is able to check step lamp operation [On/Off].
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 34 of 4801
![NISSAN TEANA 2014 Service Manual
BCS
DIAGNOSIS SYSTEM (BCM)BCS-19
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
*: Initial setting
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEADLAMP)INFOID:0000000009462002
CAUTION: NISSAN TEANA 2014 Service Manual
BCS
DIAGNOSIS SYSTEM (BCM)BCS-19
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
*: Initial setting
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEADLAMP)INFOID:0000000009462002
CAUTION:](/img/5/57390/w960_57390-33.png)
BCS
DIAGNOSIS SYSTEM (BCM)BCS-19
< SYSTEM DESCRIPTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
*: Initial setting
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEADLAMP)INFOID:0000000009462002
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentiall y causing a discharged battery and a no-start condition.
DATA MONITOR
Support Item Setting Description
DOOR LOCK-UNLOCK SET On* Automatic door locks function ON.
Off Automatic door locks function OFF.
HORN CHIRP SET Off
Horn chirp function can be changed in this mode.
On*
HAZARD LAMP SET MODE4* Lock and Unlock
Hazard warning lamp function can be changed in this mode.
MODE3 Lock Only
MODE2 Unlock Only
MODE1 OFF
AUTO LOCK SET MODE3 1 min
Auto locking function can be changed in this mode.
MODE2 OFF
MODE1* 5 min
PANIC ALRM SET MODE3 1.5 sec
Panic alarm operation can be changed in this mode.
MODE2 OFF
MODE1* 0.5 sec
PW DOWN SET MODE3 5 sec
Keyfob power window down can be changed in this mode.
MODE2 OFF
MODE1* 3 sec
Monitor Item [Unit] Description
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
ENGINE STATE [STOP/STALL/CRANK/RUN] Indicates engine status received from ECM on CAN communication line.
VEH SPEED 1 [km/h] Indicates vehicle speed signal received from ABS on CAN communication line.
TURN SIGNAL R [On/Off]
Indicates condition of combination switch.
TURN SIGNAL L [On/Off]
TAIL LAMP SW [On/Off]
HI BEAM SW [On/Off]
HEAD LAMP SW 1 [On/Off]
HEAD LAMP SW 2 [On/Off]
PASSING SW [On/Off]
AUTO LIGHT SW [On/Off]
FR FOG SW [On/Off]
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
DOOR SW-AS [On/Off] Indicates condition of front door switch RH.
DOOR SW-RR [On/Off] Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off] Indicates condition of rear door switch LH.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 50 of 4801
![NISSAN TEANA 2014 Service Manual
BCS
BCM (BODY CONTROL MODULE)BCS-35
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TAIL LAMP SW
Other than lighting switch 1ST and 2ND Off
Lighting switch 1ST or 2ND On
TP 4 The NISSAN TEANA 2014 Service Manual
BCS
BCM (BODY CONTROL MODULE)BCS-35
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TAIL LAMP SW
Other than lighting switch 1ST and 2ND Off
Lighting switch 1ST or 2ND On
TP 4 The](/img/5/57390/w960_57390-49.png)
BCS
BCM (BODY CONTROL MODULE)BCS-35
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TAIL LAMP SW
Other than lighting switch 1ST and 2ND Off
Lighting switch 1ST or 2ND On
TP 4 The ID of fourth key is not registered to BCM Yet
The ID of fourth key is registered to BCM DONE
TP 3 The ID of third key is not registered to BCM Yet
The ID of third key is registered to BCM DONE
TP 2 The ID of second key is not registered to BCM Yet
The ID of second key is registered to BCM DONE
TP 1 The ID of first key is not registered to BCM Yet
The ID of first key is registered to BCM DONE
TR CANCEL SW Trunk lid opener cancel switch OFF Off
Trunk lid opener cancel switch ON On
TR/BD OPEN SW Trunk opener switch OFF Off
While the trunk opener switch is turned ON On
TRNK/HAT MNTR Trunk lid closed Off
Trunk lid opened On
TURN SIGNAL L Turn signal switch OFF Off
Turn signal switch LH On
TURN SIGNAL R Turn signal switch OFF Off
Turn signal switch RH On
UNLK SEN-DR Driver door UNLOCK status Off
Driver door LOCK status On
VEH SPEED 1 While driving, equivalent to speedometer reading mph, km/h
VEH SPEED 2 While driving, equivalent to speedometer reading mph, km/h
WARNING LAMP Low tire pressure wa
rning lamp in combination meter OFF Off
Low tire pressure warning la mp in combination meter ON On
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 55 of 4801
![NISSAN TEANA 2014 Service Manual
BCS-40
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
60
(L) Ground CAN high Input/
Output ——
61
(Y) Ground Rear defogger relay
output OutputRear window de-
fogger Active Battery NISSAN TEANA 2014 Service Manual
BCS-40
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
60
(L) Ground CAN high Input/
Output ——
61
(Y) Ground Rear defogger relay
output OutputRear window de-
fogger Active Battery](/img/5/57390/w960_57390-54.png)
BCS-40
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
60
(L) Ground CAN high Input/
Output ——
61
(Y) Ground Rear defogger relay
output OutputRear window de-
fogger Active Battery voltage
Not activated 0V
62
(BR) Ground Starter relay output Output
Push-button igni-
tion switch ON When selector lever is in P
or N position and the brake
is depressed Battery voltage
When selector lever is in P
or N position and the brake
is not depressed 0V
64
(W) Ground Buzzer output Output Outside warning
buzzer Sounding 0V
Not sounding Battery voltage
66
(R) Ground Blower fan relay out-
put OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
67
(W) Ground Ignition electrical re-
lay output 2 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
68
(P) Ground Dimmer signal output Output
Push-button igni-
tion switch ON Either of the following con-
ditions
• Lighting switch OFF
• The area around the ve- hicle is bright (Shine a
light on the optical sen-
sor) 0V
The area around the vehi-
cle is dark (Block the light
from the optical sensor) Battery voltage
69
(L) Ground CVT device output Output — Battery voltage
70
(G) Ground IPDM E/R ignition
output 1 OutputPush-button igni-
tion switch OFF or ACC 0V
ON Battery voltage
71
(V) Ground Driver request switch Input
Front door LH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
72
(Y) Ground Passenger request
switch InputFront door RH re-
quest switch ON (pressed) 0V
OFF (not pressed) 1.0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JPMIA0016GB
JPMIA0016GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 99 of 4801

PRECAUTIONSBR-3
< PRECAUTION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951709
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service t he system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three mi nutes before performing any service.
Precaution for Procedure without Cowl Top CoverINFOID:0000000009463677
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Brake SystemINFOID:0000000009463678
WARNING:
Clean any dust from the front brake and rear brake wi th a vacuum dust collector. Never blow with com-
pressed air.
CAUTION:
• Brake fluid use. Refer to MA-11, "FOR USA AND CANADA : Fluids and Lubricants"
.
• Do not reuse drained brake fluid.
• Do not spill or splash brake fluid on painted su rfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with wa ter if it gets on a painted surface.
• Always clean with new brake fluid when cleaning th e master cylinder, brake caliper and other com-
ponents.
• Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and
cause improper operation.
• Always loosen the brake tube flar e nut with a flare nut wrench.
PIIB3706J
Revision: November 20132014 Altima NAM
Page 150 of 4801
![NISSAN TEANA 2014 Service Manual
BRC-4
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951721
The Supplemen NISSAN TEANA 2014 Service Manual
BRC-4
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951721
The Supplemen](/img/5/57390/w960_57390-149.png)
BRC-4
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951721
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Brake SystemINFOID:0000000009463735
WARNING:
Clean any dust from the front brake and rear br ake using a vacuum dust collector. Do not blow by
compressed air.
• Brake fluid use refer to BR-8, "Inspection"
.
• Do not reuse drained brake fluid.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off immediately and wash with water if it gets on a painted surface.
• Always confirm the specified tightening torque when installing the brake pipes.
• After pressing the brake pedal more deeply or harder t han normal driving, such as air bleeding, check each
item of brake pedal. Adjust brake pedal if it is outside the standard value.
• Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and cause
improper operation.
• Always loosen the brake tube flar e nut with a flare nut wrench.
• Tighten the brake tube flare nut to the specified torque with a crow-
foot (A) and torque wrench (B).
• Always connect the battery terminal when moving the vehicle.
• Turn the ignition switch OFF and disconnect the ABS actuator and
electric unit (control unit) harness connector or the battery negative
terminal before performing the work.
• Check that no brake fluid leakage is present after replacing the parts.
JPFIA0001ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 151 of 4801
![NISSAN TEANA 2014 Service Manual
PRECAUTIONSBRC-5
< PRECAUTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Precaution for Brake ControlINFOID:0000000009463736
• During ABS operation, the brake pedal may vibrate lightly and NISSAN TEANA 2014 Service Manual
PRECAUTIONSBRC-5
< PRECAUTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Precaution for Brake ControlINFOID:0000000009463736
• During ABS operation, the brake pedal may vibrate lightly and](/img/5/57390/w960_57390-150.png)
PRECAUTIONSBRC-5
< PRECAUTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
Precaution for Brake ControlINFOID:0000000009463736
• During ABS operation, the brake pedal may vibrate lightly and a mechanical noise may be heard. This is normal.
• Just after starting vehicle, the brake pedal may vibrate or a motor operating noise may be heard from engine
compartment. This is a normal status of operation check.
• Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel, or
snow-covered (fresh, deep snow) roads.
• When an error is indicated by ABS or another warning lamp, collect all necessary information from customer
(what symptoms are present under what conditions) and check for simple causes before starting diagnosis.
Besides electrical system inspection, check boos ter operation, brake fluid level, and fluid leaks.
• If incorrect tire sizes or types are installed on the vehicle or brake pads are not Genuine NISSAN parts, stop-
ping distance or steering stability may deteriorate.
• If there is a radio, antenna or related wiring near control module, ABS function may have a malfunction or
error.
• If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness pinches, open circuits or improper wiring.
• If the following components are replaced with non-genuine components or modified, the VDC OFF indicator
lamp and SLIP indicator lamp may turn on or the VDC system may not operate properly. Components
related to suspension (shock absorbers, struts, springs , bushings, etc.), tires, wheels (exclude specified
size), components related to brake system (pads, roto rs, calipers, etc.), components related to engine (muf-
fler, ECM, etc.), components related to body reinforcement (roll bar, tower bar, etc.).
• Driving with broken or excessively worn suspensi on components, tires or brake system components may
cause the VDC OFF indicator lamp and the SLIP indicator lamp to turn on, and the VDC system may not
operate properly.
• When the TCS or VDC is activated by sudden acceleration or sudden turn, some noise may occur. The
noise is a result of the normal operation of the TCS and VDC.
• When driving on roads which have extreme slopes (such as mountainous roads) or high banks (such as sharp curves on a freeway), the VDC may not operate no rmally, or the VDC warning lamp and the SLIP indi-
cator lamp may turn on. This is not a problem if normal operation can be resumed after restarting the engine.
• Sudden turns (such as spin turns, acceleration turns), drifting, etc. with VDC turned off may cause the yaw rate/side/decel G sensor to indicate a problem. This is not a problem if normal operation can be resumed
after restarting the engine.
Precaution for CAN SystemINFOID:0000000009463737
• Do not apply voltage of 7.0V or higher to terminal to be measured.
• Maximum open terminal voltage of tester in use must be less than 7.0V.
• Before checking harnesses, turn ignition switch OFF and disconnect battery negative cable.
• Area to be repaired must be soldered and wrapped with tape. Make sure that fraying of twisted wire is within 110 mm (4.33 in).
PKIA0306E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM