air filter NISSAN TEANA 2014 Owner's Manual

HA-40
< REMOVAL AND INSTALLATION >
HEATING AND COOLING UNIT ASSEMBLY
HEATING AND COOLING UNIT ASSEMBLY
Exploded ViewINFOID:0000000009463948
HEATING AND COOLING UNIT ASSEMBLY
1. Heating and cooling unit assembly 2. Harness 3. Mode door motor
4. Upper floor connecting duct (LH) 5. Air mix door motor (passenger) (automatic A/C only)6. Heater core pipes cover
7. Heater core 8. Evaporator 9. Air mix door motor (driver)
10. Upper floor connecting duct (RH) 11. Expansion valve 12. Blower motor
13. Intake door motor 14. Blower unit 15. Filter cover
16. In-cabin microfilter
ALIIA0618ZZ
Revision: November 20132014 Altima NAM

HAC-18
< SYSTEM DESCRIPTION >[AUTOMATIC AIR CONDITIONER]
SYSTEM
*: Inlet status is displayed by indicator during activating automatic control
AIR DISTRIBUTION
1. Intake door 2. Blower motor 3. In-cabin microfilter
4. Front evaporator 5. Air mix door 6. Front heater core
7. Foot door 8. Ventilator door 9. Defroster door
10. Max. cool door
Fresh air Recirculation air Discharge air
Defroster Center ventilator Side ventilator
Front foot Rear foot
Switch position Door position
Mode door
Intake door
Air mix door
Ventilator door
Max. cool door Defroster door Foot door
(Driver side)
(Passenger side)
AUTO switch AUTO
MODE switch AAAA
———
BBAB
CCB B
CBBB
DEF switch C A C C
Intake switch
*
———— A
B
Temperature control
switch (Driver side) DUAL
switch:
OFF Full cold
[18 °C (60 °F)]
—A
18.5 °C – 31.5 °C
(61 °F – 89 °F) AUTO
Full hot
[32 °C (90 °F)] B
Temperature control
switch (Driver side)
DUAL
switch:
ON Full cold
[18 °C (60 °F)] A
—
18.5
°C – 31.5 °C
(61 °F – 89 °F) AUTO
Full hot
[32 °C (90 °F)] B
Temperature control
switch (Passenger
side) Full cold
[18 °C (60 °F)]
—A
18.5 °C – 31.5 °C
(61 °F – 89 °F) AUTO
Full hot
[32 °C (90 °F)] B
ON·OFF switch OFF C C B B B —
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

LAN
SYSTEMLAN-31
< SYSTEM DESCRIPTION > [CAN]
C
D E
F
G H
I
J
K L
B
A
O P
N
*: These are the only control units wired with both ends of CAN communication system.
CAN COMMUNICATION SYSTEM : CAN
System Specification ChartINFOID:0000000009461412
Determine CAN system type from the following specification chart.
NOTE:
Refer to LAN-18, "Trouble Diagnosis Procedure"
for how to use CAN system specification chart.
×: Applicable
VEHICLE EQUIPMENT IDENTIFICATION INFORMATION
NOTE:
Check CAN system type from the vehicle shape and equipment.
Noise filter It eliminates noise of CAN communication signal.
Termination circuit
*
(Resistance of approx. 120 Ω) Generates a potential difference between CAN-H and CAN-L.
Component System description
Body type
Sedan
Axle 2WD
Engine QR25DE VQ35DE
Transmission CVT
Brake control VDC
Driver assistance system ××
Navigation system ×× ××
Automatic air conditioner ××× ×××
CAN system type 12345678 CAN communication unit
ECM ××××××××
ABS actuator and electric unit (control unit) ××××××××
Power steering control module ××××××××
IPDM E/R ××××××××
TCM ××××××××
Data link connector ××××××××
Combination meter ××××××××
Steering angle sensor ××××××××
AV control unit ×× ××
ITS control unit ××
A/C auto amp. ××× ×××
BCM ××××××××
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

LU-1
ENGINE
C
D E
F
G H
I
J
K L
M
SECTION LU
A
LU
N
O P
CONTENTS
ENGINE LUBRICATION SYSTEM
QR25DE
PRECAUTION ................ ...............................
3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
Precaution for Liquid Gasket .....................................3
PREPARATION ............................................5
PREPARATION .............................................. .....5
Special Service Tool ........................................... ......5
Commercial Service Tool ..........................................5
SYSTEM DESCRIPTION ..............................7
LUBRICATION SYSTEM ............................... .....7
Lubrication Circuit ............................................... ......7
Schematic .................................................................8
PERIODIC MAINTENANCE ..........................9
ENGINE OIL ................................................... .....9
Inspection ............................................................ ......9
Changing Engine Oil ...............................................10
OIL FILTER ........................................................11
Removal and Installation .........................................11
REMOVAL AND INSTALLA TION ...............13
OIL PUMP ....................................................... ....13
Exploded View .................................................... ....13
Removal and Installation .........................................13
Disassembly and Assembly ................................ ....13
Inspection ................................................................14
OIL COOLER ......................................................16
Exploded View .................................................... ....16
Removal and Installation .........................................16
Inspection ............................................................ ....17
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... .............................................
18
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
18
Oil Pressure ......................................................... ....18
Oil Pump ..................................................................18
Regulator Valve .......................................................18
Oil Capacity .............................................................18
VQ35DE
PRECAUTION ...... ........................................
19
PRECAUTIONS .................................................19
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
19
Precaution for Liquid Gasket ...................................19
PREPARATION ...........................................21
PREPARATION .................................................21
Special Service Tool ............................................ ....21
Commercial Service Tool ........................................21
SYSTEM DESCRIPTION .............................23
LUBRICATION SYSTEM ..................................23
Lubrication Circuit ................................................ ....23
Schematic ................................................................24
PERIODIC MAINTENANCE ........................25
ENGINE OIL ......................................................25
Inspection ............................................................ ....25
Changing Engine Oil ................................................26
OIL FILTER .......................................................27
Removal and Installation .........................................27
REMOVAL AND INSTALLATION ...............29
Revision: November 20132014 Altima NAM

ENGINE OILLU-9
< PERIODIC MAINTENANCE > [QR25DE]
C
D E
F
G H
I
J
K L
M A
LU
NP
O
PERIODIC MAINTENANCE
ENGINE OIL
InspectionINFOID:0000000009461028
OIL LEVEL
• Before starting the engine, check the oil level. If t
he engine is already started, stop it and allow 10 minutes
before checking.
• Check that the oil level is within the range (A) on the oil level
gauge.
• If it is out of range, add oil as necessary.
ENGINE OIL APPEARANCE
• Check engine oil for white milky appearance or excessive contamination.
• If engine oil becomes milky, it is highly probable t hat it is contaminated with engine coolant. Repair or
replace damaged parts.
OIL LEAKAGE
Check for oil leakage around the following areas:
•Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Oil cooler
• Valve timing control cover and valve timing control solenoid valve
• Front cover
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Crankshaft oil seal (front and rear)
OIL PRESSURE CHECK
WARNING:
• Be careful not to burn yoursel f, as engine oil may be hot.
• Put the CVT shift selector in the Park "P" position.
1. Check engine oil level. Refer to OIL LEVEL.
2. Remove fender protector side cover (RH). Refer to EXT-26, "FENDER PROTECTOR : Exploded View"
.
3. Disconnect oil pressure switch harness connector at oil pressure switch. Remove oil pressure switch and install Tools.
CAUTION:
Do not drop or shock oil pressure switch.
4. Start engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load, using Tool. NOTE:
JPBIA1497ZZ
Tool numbers : ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Revision: November 20132014 Altima NAM

LU-12
< PERIODIC MAINTENANCE >[QR25DE]
OIL FILTER
4. Refill engine with new engine oil. Refer to
LU-10, "Changing Engine Oil".
5. After warming up the engine, check for engine oil leaks. Repair as necessary.
6. Install fender protector side cover (RH). Refer to EXT-26, "FENDER PROTECTOR : Exploded View"
.
Revision: November 20132014 Altima NAM

ENGINE OILLU-25
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
LU
NP
O
PERIODIC MAINTENANCE
ENGINE OIL
InspectionINFOID:0000000009461048
OIL LEVEL
NOTE:
• Before starting the engine, check the oil level. If the engine is already started, stop it and a llow 10 minutes before checking.
• Check that the oil level is within the range as indicated on the oil level gauge.
• If it is out of range, add oil as necessary.
ENGINE OIL APPEARANCE
• Check engine oil for white milky appearance or excessive contamination.
• If engine oil becomes milky, it is highly probable t hat it is contaminated with engine coolant. Repair or
replace damaged parts.
OIL LEAKAGE
Check for oil leakage around the following areas:
•Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Oil cooler
• Intake valve timing control cover and intake valve timing control solenoid valve
• Front cover
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Crankshaft oil seal (front and rear)
OIL PRESSURE CHECK
WARNING:
• Be careful not to burn yoursel f, as engine oil may be hot.
• Put the CVT shift selector in the Park “P” position.
1. Check the oil level.
2. Remove fender protector side cover (RH). Refer to EXT-26, "FENDER PROTECTOR : Exploded View"
.
3. Disconnect oil pressure switch harness connector at the oil pressure switch. Remove oil pressure switch and install Tools.
CAUTION:
Do not drop or shock oil pressure switch.
4. Start the engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load, using Tool. NOTE:
• When engine oil temperature is low, engine oil pressure becomes high.
JMA122D
Tool numbers : ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Revision: November 20132014 Altima NAM

OIL COOLERLU-33
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
LU
NP
O
When removing components such as hoses, tubes/lines, etc.
, cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the engine under cover. Refer to EXT-17, "Removal and Installation".
2. Remove the RH wheel and tire. Refer to WT-53, "Inspection"
.
3. Remove the front fender protector side cover RH. Refer to EXT-26, "FENDER PROTECTOR : Exploded
View".
4. Drain engine coolant. Refer to CO-36, "Changing Engine Coolant"
.
CAUTION:
Do not spill coolant on the drive belt.
5. Disconnect water hoses from oil cooler.
6. Remove the oil filter. Refer to LU-27, "Removal and Installation"
.
7. Remove oil cooler.
8. Remove core support cover. Refer to DLK-179, "Removal and Installation"
.
9. Remove front air duct. Refer to EM-84, "Removal and Installation"
.
10. Remove reservoir tank. Refer to CO-40, "Exploded View"
.
INSPECTION AFTER REMOVAL
1. Check oil cooler for cracks.
2. Check oil cooler for clogging by blowing through coolant inlet. If necessary, replace oil cooler.
Oil Pressure Relief Valve
Inspect oil pressure relief valve for movement, cracks and breaks by pushing the ball. If replacement is neces-
sary, remove valve by prying it out with a suitable tool. Install a new valve in place by tapping it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Do not reuse copper gasket.
• When installing the oil cooler, align the oil cooler slot with the stopper of the oil pan.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to LU-9, "Inspection"
and CO-11, "System Inspection".
2. Start the engine, and check that there is no leakage of engine oil or engine coolant.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and the engine coolant level again. Refer to LU-9, "Inspection"
and CO-11,
"System Inspection".
Revision: November 20132014 Altima NAM

MA-1
MAINTENANCE
C
D E
F
G H
I
J
K L
M B
MA
SECTION MA
N
O A
CONTENTS
MAINTENANCE
PRECAUTION ................
...............................3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
PREPARATION ............................................4
PREPARATION .............................................. .....4
Special Service Tool ........................................... ......4
Commercial Service Tool ..........................................4
PERIODIC MAINTENANCE ..........................5
GENERAL MAINTE NANCE ........................... .....5
FOR USA AND CANADA ...................................... ......5
FOR USA AND CANADA : Explanation of General
Maintenance ........................................................ ......
5
PERIODIC MAINTENANCE ................................7
FOR USA AND CANADA ...................................... ......7
FOR USA AND CANADA : Introduction of Periodic
Maintenance ........................................................ ......
7
RECOMMENDED FLUIDS AND LUBRI-
CANTS ............................................................ ....
11
FOR USA AND CANADA ...................................... ....11
FOR USA AND CANADA : Fluids and Lubricants ....11
FOR USA AND CANADA : Engine Oil Recom-
mendation ........................................................... ....
11
FOR USA AND CANADA : Engine Coolant Mix-
ture Ratio ............................................................. ....
12
ENGINE MAINTENANCE (QR25DE) .................13
DRIVE BELTS ....................................................... ....13
DRIVE BELTS : Checking Drive Belts ....................13
DRIVE BELTS : Tension Adjustment ......................13
ENGINE COOLANT ............................................... ....13
ENGINE COOLANT : System Inspection ................13
ENGINE COOLANT : Changing Engine Coolant ....14
FUEL LINES ........................................................... ....16
FUEL LINES : Inspection .........................................16
AIR CLEANER FILTER ......................................... ....16
AIR CLEANER FILTER : Removal and Installation
....
17
ENGINE OIL ........................................................... ....17
ENGINE OIL : Inspection .........................................17
ENGINE OIL : Changing Engine Oil ........................17
OIL FILTER ............................................................ ....18
OIL FILTER : Removal and Installation ...................18
SPARK PLUG ........................................................ ....19
SPARK PLUG : Removal and Installation ...............20
EVAP VAPOR LINES ............................................ ....21
EVAP VAPOR LINES : Inspection ...........................21
ENGINE MAINTENANCE (VQ35DE) ................22
DRIVE BELTS ........................................................ ....22
DRIVE BELTS : Checking Drive Belts .....................22
DRIVE BELTS : Tension Adjustment ......................22
ENGINE COOLANT ............................................... ....22
ENGINE COOLANT : System Inspection ................22
ENGINE COOLANT : Changing Engine Coolant ....23
FUEL LINES ........................................................... ....25
FUEL LINES : Inspection .........................................25
AIR CLEANER FILTER ......................................... ....25
AIR CLEANER FILTER : Removal and Installation
....
26
ENGINE OIL ........................................................... ....26
ENGINE OIL : Inspection .........................................26
ENGINE OIL : Changing Engine Oil ........................27
OIL FILTER ............................................................ ....27
Revision: November 20132014 Altima NAM

PERIODIC MAINTENANCEMA-7
< PERIODIC MAINTENANCE >
C
D E
F
G H
I
J
K L
M B
MA
N
O A
PERIODIC MAINTENANCE
FOR USA AND CANADA
FOR USA AND CANADA : Introduc
tion of Periodic MaintenanceINFOID:0000000009889991
The following tables show the normal maintenanc e schedule. Depending upon weather and atmospheric con-
ditions, varying road surfaces, indi vidual driving habits and vehicle usage, additional or more frequent mainte-
nance may be required.
Periodic maintenance beyond th e last period shown on the tables requires similar maintenance.
Emission Control System Maintenance
Abbreviations: R = Replace. I = Inspec t. Correct or replace if necessary.
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Perform at number of miles, kilometers
or months, whichever comes first. Miles x 1,000
(km x 1,000) Months 5
(8) 6 10
(16) 12 15
(24) 18 20
(32) 24 25
(40) 30 30
(48) 36 35
(56) 42 40
(64) 48 45
(72) 54
Drive belt NOTE (1) I*
Air cleaner filter NOTE (2) R
EVAP vapor lines I* I*
Fuel lines I* I*
Fuel filter NOTE (3)
Engine coolant* NOTE (4)(5)
Engine oil RRRRRRRRR
Engine oil filter (Use genuine NISSAN
engine oil filter or equivalent) RRRRRRRRR
Spark plugs (Iridium - tipped type) NOTE (6) Replace every 105,000 miles (168,000 km)
Intake and exhaust valve clearance* NOTE (7)
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Perform at number of miles, kilometers
or months, whichever comes first. Miles x 1,000
(km x 1,000)
Months 50
(80)
60 55
(88)
66 60
(96)
72 65
(104)
78 70
(112)
84 75
(120)
90 80
(128)
96 85
(136)
102 90
(144)
108
Drive belt NOTE (1)I*I*I*I*I*
Air cleaner filter NOTE (2) R R
EVAP vapor lines I* I*
Fuel lines I* I*
Fuel filter NOTE (3)
Engine coolant* NOTE (4)(5)
Engine oil RRRRRRRRR
Engine oil filter (Use genuine NISSAN
engine oil filter or equivalent) RRRRRRRRR
Spark plugs (Iridium - tipped type) NOTE (6) Replace every 105,000 miles (168,000 km)
Intake and exhaust valve clearance* NOTE (7)
MAINTENANCE OPERATION MAINTENANCE INTERVAL
Reference Page
Perform at number of miles, kilometers
or months, whichever comes first. Miles x 1,000
(km x 1,000)
Months 95
(152)
11 4 100
(160)
120 105
(168)
126 11 0
(176)
132 11 5
(184)
138 120
(192)
144
Drive belt NOTE (1) I* I* I* MA-13
(QR25DE)
MA-22
(VQ35DE)
Air cleaner filter NOTE (2) R MA-17
(QR25DE)
MA-26
(VQ35DE)
Revision: November 20132014 Altima NAM