SEC NISSAN TEANA 2014 Service Manual

INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
When installing the front kicking plate inner, check that the pawls are securely placed in the body
panel holes.
FRONT KICKING PLATE : Remova l and Installation - OuterINFOID:0000000009461350
REMOVAL
1. Release the front kicking plate outer pawls and remove the front
kicking plate outer.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing the front kicking plate outer, ch eck that the pawls are securely placed in the body
panel holes.
REAR KICKING PLATE
REAR KICKING PLATE : Remova l and Installation - InnerINFOID:0000000009461351
REMOVAL
1. Remove the rear seat cushion. Refer to SE-36, "Removal and Installation - Seat Assembly".
2. Release the rear kicking plate inner pawls and clip, then remove the rear kicking plate inner.
: Clip
: Pawl
NOTE:
RH side shown; LH side similar.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clip and pawls for deformation and damage during installation. Replace as neces-
sary.
• When installing the rear kicking plate inner, check that the clip and pawls are securely placed in the
body panel holes.
REAR KICKING PLATE : Remova l and Installation - OuterINFOID:0000000009461352
REMOVAL
ALJIA0888ZZ
ALJIA0889ZZ
Revision: November 20132014 Altima NAM

BODY SIDE TRIMINT-23
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
INT
N
O P
1. Release the rear kicking plate outer pawls and remove the rear kicking plate outer.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing the rear kicking plate outer, ch eck that the pawls are securely placed in the body
panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Inst allation - Front Body Side WeltINFOID:0000000009461353
REMOVAL
1. Remove the dash side finisher. Refer to INT-20, "DASH SIDE FINISHER : Removal and Installation".
2. Remove the center pillar lower finisher. Refer to INT-23, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
3. Remove the front body side welt.
INSTALLATION
Installation is in the reverse order of removal.
BODY SIDE WELT : Removal and In stallation - Rear Body Side WeltINFOID:0000000009461354
REMOVAL
1. Remove the center pillar lower finisher. Refer to INT-23, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
2. Remove the rear body side welt.
INSTALLATION
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and InstallationINFOID:0000000009461355
REMOVAL
1. Move the front seat to the full forward position.
2. Remove the front kicking plate inner. Refer to INT-21, "FRONT KICKING PLATE : Removal and Installa-
tion - Inner".
3. Remove the rear kicking plate inner. Refer to INT-22, "REAR KICKING PLATE : Removal and Installation
- Inner".
4. Partially remove the front body side welt. Refer to INT-23, "BODY SIDE WELT : Removal and Installation
- Front Body Side Welt".
5. Partially remove the rear body side welt. Refer to INT-23, "BODY SIDE WELT : Removal and Installation -
Rear Body Side Welt".
ALJIA0890ZZ
Revision: November 20132014 Altima NAM

INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
6. Release the center pillar lower finisher clips.: Clip
7. Remove the seat belt from the center pillar lower fi nisher, then remove the center pillar lower finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and dama ge during installation. Replace with new ones if
necessary.
• When installing the center pillar lower finisher, check that the clips are securely placed in the body
panel holes.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and InstallationINFOID:0000000009461356
REMOVAL
1. Move the front seat to the full forward position.
2. Remove the center pillar lower finisher. Refer to INT-23, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
3. Remove the seat belt bolt cover (1) and seat belt bolt (A).
4. Release the clip and pawl, then remove the center pillar upper finisher (1).
: Clip
: Pawl
CAUTION:
Do not reuse the center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse the center pillar upper finisher. Replace with new part for installation.
• When installing the center pillar upper finisher, check that the clip and pawl are securely placed in
the body panel holes.
ALJIA0901ZZ
ALJIA0902ZZ
ALJIA0903ZZ
Revision: November 20132014 Altima NAM

BODY SIDE TRIMINT-25
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
K L
M A
B
INT
N
O P
REAR PILLAR FINISHER
REAR PILLAR FINISHER : Removal and InstallationINFOID:0000000009461357
REMOVAL
1. Remove the rear seat bolster. Refer to SE-38, "Removal and Installation - Rear Seat Bolster".
2. Partially remove the rear body side welt. Refer to INT-23, "BODY SIDE WELT : Removal and Installation -
Rear Body Side Welt".
3. Release the rear pillar finisher clips and pawls and push pin (A). : Clip
: Metal clip
: Pawl
4. Remove the rear pillar finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips, metal clips and pawls for deformation and damage during installation.
Replace with new ones if necessary.
• When installing the rear pillar finisher, check that the clips, metal clips, push pin and pawls are
securely fitted in the body panel holes.
ALJIA0904ZZ
Revision: November 20132014 Altima NAM

IP-1
BODY INTERIOR
C
D E
F
G H
I
K L
M
SECTION IP
A
B
IP
N
O P
CONTENTS
INSTRUMENT PANEL
PRECAUTION ................ ...............................2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution for Work ..................................................2
PREPARATION ............................................3
PREPARATION .............................................. .....3
Special Service Tools ........................................ ......3
Commercial Service Tools .......................................3
CLIP LIST ............................................................4
Descriptions for Clips .......................................... ......4
SYMPTOM DIAGNOSIS ...............................8
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ........................................................... .....
8
Work Flow ........................................................... ......8
Generic Squeak and Rattle Troubleshooting ............9
Diagnostic Worksheet .............................................12
REMOVAL AND INSTALLATION ...............14
INSTRUMENT PANEL ASSEMBLY .............. ....14
Exploded View ..................................................... ....14
Removal and Installation .........................................15
STEERING COLUMN COVERS .......................17
Removal and Installation .........................................17
CENTER CONSOLE ASSEMBLY ....................18
Exploded View .........................................................18
Removal and Installation .........................................18
CLUSTER LID A ...............................................19
Removal and Installation .........................................19
CLUSTER LID C ...............................................20
Cluster Lid C ............................................................20
Cluster Lid C Lower .................................................20
INSTRUMENT LOWER PANEL LH ..................21
Removal and Installation .........................................21
GLOVE BOX ASSEMBLY ................................22
Removal and Installation .........................................22
UNIT DISASSEMBLY AND ASSEMBLY ....23
CENTER CONSOLE ASSEMBLY ....................23
Exploded View ..................................................... ....23
Disassembly and Assembly .....................................23
Revision: November 20132014 Altima NAM

IP-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951558
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009461371
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAM

IP-8
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SYMPTOM DIAGNOSIS
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work FlowINFOID:0000000009889928
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to IP-12, "Diagnostic Worksheet"
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist w hen the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer is
concerned about. This can be accomplished by test driving the vehicle with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak —(Like tennis shoes on a clean floor) Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping.
• Creak—(Like walking on an old wooden floor) Creak characteristics include firm contact/slow mo vement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle—(Like shaking a baby rattle) Rattle characteristics include the fast repeated contac t/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock —(Like a knock on a door) Knock characteristics include hollow sounding/someti mes repeating/often brought on by driver action.
• Tick—(Like a clock second hand) Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump—(Heavy, muffled knock noise)
Thump characteristics include softer k nock/dead sound often brought on by activity.
• Buzz—(Like a bumble bee) Buzz characteristics include hi gh frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending upon the person. A noise that you may judge
as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperat ure, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
SBT842
Revision: November 20132014 Altima NAM

SQUEAK AND RATTLE TROUBLE DIAGNOSESIP-9
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
K L
M A
B
IP
N
O P
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or lo cation of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on CVT and A/T models).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
• Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
• If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, che ck ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area. To help pi npoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear: J-39565 and mechanic's stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by: • removing the components in the area that you suspect the noise is coming from.Do not use too much force when removing clips and fasteners, otherwise clips and fasteners can be
broken or lost during the repair, resulting in the creation of new noise.
• tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.
• feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.
• placing a piece of paper between components that you suspect are causing the noise.
• looking for loose components and contact marks. Refer to IP-9, "Generic Squeak and Rattle Troubleshooting"
.
REPAIR THE CAUSE
• If the cause is a loose component, tighten the component securely.
• If the cause is insufficient clearance between components:
- separate components by repositioning or loos ening and retightening the component, if possible.
- insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or urethane
tape. A NISSAN Squeak and Rattle Kit (J-50397) is av ailable through your authorized NISSAN Parts Depart-
ment.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
NOTE:
• Always check with the Parts Department for the latest parts information.
• The materials contained in the NISSAN Squeak and Rattle Kit (J-50397) are listed on the inside cover of the
kit; and can each be ordered seperately as needed.
• The following materials not found in the kit can also be used to repair squeaks and rattles.
- SILICONE GREASE: Use instead of UHMW tape that will be visible or does not fit. The silicone grease will
only last a few months.
- SILICONE SPRAY: Use when grease cannot be applied.
- DUCT TAPE: Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingINFOID:0000000009889929
Refer to Table of Contents for specific component removal and installation information.
Revision: November 20132014 Altima NAM

SQUEAK AND RATTLE TROUBLE DIAGNOSESIP-11
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
K L
M A
B
IP
N
O P
1. Loose harness or harness connectors.
2. Front console map/reading lamp lens loose.
3. Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the pos ition the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplic ated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of thes e incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component installed to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator installation pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine rpm or
load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: November 20132014 Altima NAM

LAN
LAN-1
ELECTRICAL & POWER CONTROL
C
D E
F
G H
I
J
K L
B
SECTION LAN
A
O P
N
CONTENTS
LAN SYSTEM
CAN FUNDAMENTAL
HOW TO USE THIS MANU AL ......................
7
HOW TO USE THIS SECTION ....................... .....7
Information .......................................................... ......7
PRECAUTION ...............................................8
PRECAUTIONS .............................................. .....8
Precautions for Trouble Diagnosis ...................... ......8
Precautions for Harness Repair ................................8
SYSTEM DESCRIPTION . .............................9
SYSTEM ......................................................... .....9
CAN COMMUNICATION SYSTEM .............................9
CAN COMMUNICATION SYSTEM : System De-
scription ............................................................... ......
9
DIAG ON CAN ....................................................... ......9
DIAG ON CAN : System Description ........................9
TROUBLE DIAGNOSIS .....................................11
Component Description ....................................... ....11
Condition of Error Detection ....................................11
Symptom When Error Occurs in CAN Communi-
cation System ...................................................... ....
12
CAN Diagnosis with CONSULT ..............................14
Self-Diagnosis .........................................................15
CAN Diagnostic Support Monitor ............................15
How to Use CAN Communication Signal Chart ......17
BASIC INSPECTION ...................................18
DIAGNOSIS AND REPAIR WORKFLOW ..... ....18
Trouble Diagnosis Flow Chart ............................. ....18
Trouble Diagnosis Procedure ..................................18
CAN
HOW TO USE THIS MANU AL .....................
23
HOW TO USE THIS SECTION .........................23
Information ........................................................... ....23
Abbreviation List ......................................................23
PRECAUTION ..............................................24
PRECAUTIONS .................................................24
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
24
Precautions for Trouble Diagnosis ..........................24
Precautions for Harness Repair ..............................24
SYSTEM DESCRIPTION .............................26
COMPONENT PARTS ......................................26
Component Parts Location .................................. ....26
SYSTEM ............................................................27
CAN COMMUNICATION SYSTEM ........................ ....27
CAN COMMUNICATION SYSTEM : System De-
scription ............................................................... ....
27
CAN COMMUNICATION SYSTEM : CAN Com-
munication Control Circuit ................................... ....
30
CAN COMMUNICATION SYSTEM : CAN System
Specification Chart .............................................. ....
31
CAN COMMUNICATION SYSTEM : CAN Com-
munication Signal Chart ...................................... ....
32
WIRING DIAGRAM ......................................36
CAN SYSTEM .. ................................ .................36
Wiring Diagram .................................................... ....36
BASIC INSPECTION ...................................42
DIAGNOSIS AND REPAIR WORKFLOW ........42
Interview Sheet .................................................... ....42
DTC/CIRCUIT DIAGNOSIS .........................43
MALFUNCTION AREA CHART ........................43
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM