NISSAN TERRANO 2004 Service Repair Manual
TERRANO 2004
NISSAN
NISSAN
https://www.carmanualsonline.info/img/5/57394/w960_57394-0.png
NISSAN TERRANO 2004 Service Repair Manual
Page 1749 of 1833
RHD MODELS
YEL757E
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-256
http://vnx.su/
Page 1750 of 1833
RHD MODELS
YEL180D
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-257
http://vnx.su/
Page 1751 of 1833
RHD MODELS
YEL181D
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-258
http://vnx.su/
Page 1752 of 1833
RHD MODELS
YEL868E
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-259
http://vnx.su/
Page 1753 of 1833
RHD MODELS
YEL183D
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-260
http://vnx.su/
Page 1754 of 1833
RHD MODELS
YEL184D
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-261
http://vnx.su/
Page 1755 of 1833
RHD MODELS
YEL758E
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-262
http://vnx.su/
Page 1756 of 1833
RHD MODELS
YEL186D
THEFT WARNING SYSTEM
Wiring Diagram Ð THEFT Ð (Cont'd)EL-263
http://vnx.su/
Page 1757 of 1833

Trouble Diagnoses
Alarm Trigger Feedback
To verify the last three triggers that activated the theft warning system, the Time Control Unit (TCU) can be
switched into Diagnostic Mode (see page EL-218 how to enter Diagnostic Mode).
Approximately 2 seconds after the TCU has finished flashing the hazard lamp to confirm that the Diagnostic
Mode has been successfully entered, the TCU will generate a short beep indicating the trigger that will be dis-
played. A single beep means the most recent trigger, three beeps means the oldest trigger. Following each
beep or group of beeps, the hazard lamp will flash to indicate the alarm trigger.
Source of Alarm TriggerNumber (of flashes)
Driver's door lock status switch 1
Passenger door lock status switch 2
Rear door lock status switch 3
Ignition line 4
Driver's door open switch 5
Other door open switch 6
Trunk or back door open switch 8
Hood switch 9
Ultrasonic sensors 10
In case there have been no alarm triggers, there will be no indicator flashes between the audible signals. After
completing the alarm trigger feedback, the TCU will enter Diagnostic Mode as described on page EL-218.
Before continuing trouble diagnoses on the next page, perform the checks as mentioned in the table on page
EL-219.
THEFT WARNING SYSTEM
EL-264
http://vnx.su/
Page 1758 of 1833

PRELIMINARY CHECK
The system operation is canceled by turning the ignition switch to ªONº at any step between START and
ARMED in the following flow chart.
System phaseSTART
Note: Before starting operation check, open front windows.
EDISARMED Turn ignition switch ªOFFº and remove the ignition key.
ªSECURITYº indicator lamp will blink every 2.6 seconds.
(NATS)
OK
ENGRefer to NATS
trouble diagno-
sis.
Close all doors, hood and trunk lid.
Press the ultrasonic cancel switch. The ªSECURITYº indicator lamp
will go on for approximately 6 seconds.
OK
ENGSYMPTOM 1
PRE-ARMED Lock doors using key or multi-remote controller.
ARMEDFor about 30 seconds, ªSECURITYº indicator lamp will blink inter-
mittently.
OK
ENGSYMPTOM 2
Disarm the system by unlocking the vehicle using the remote con-
troller. Arm the system again without excluding the ultrasonic sen-
sors.
ALARM Unlock any door without multi-remote controller, activate the ultra-
sonic sensors by inserting an object into the vehicle's interior, or
open hood or door.
........................................................................\
...............................
Alarm (horn and hazard lamp) will operate.
OK
ENGSYMPTOM 3
ENGSYMPTOM 4
EDISARMED Unlock the vehicle using the multi-remote controller or insert the
key in the ignition and switch it to ON.
Alarm (horn and hazard lamp) will stop.
OK
ENGSYMPTOM 5
System is OK.
After performing preliminary check, go to ªSYMPTOM CHARTº, EL-266.
H
H
H
HH
HH
H
HH
HH
H
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont'd)
EL-265
http://vnx.su/