cruise control NISSAN TIIDA 2007 Service Owner's Manual

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-217
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
Engine Speed Does Not Return to Idle (Light Braking D4 → D3 )UCS005VA
SYMPTOM:
Engine speed does not smoothly return to idle when A/T shifts from D4 to D3 on “Cruise Test — Part
1”.
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT-82, "
SELF-DIAGNOSTIC RESULT MODE" or AT-90, "Diagnostic Proce-
dure Without CONSULT-II" .
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning system. Refer to AT- 8 2 , "SELF-DIAGNOSTIC RESULT MODE" or AT-
91, "Judgement of Self-diagnosis Code" .
NO >> GO TO 2.
2. CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to EC-532, "
DTC P2138 APP SENSOR" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace accelerator pedal position sensor.
3. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-257, "
Components" .
2. Check A/T fluid condition. Refer to AT-53, "
Fluid Condition Check" .
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. DETECT MALFUNCTIONING ITEM
1. Remove control valve assembly. Refer to AT-242, "
Control Valve Assembly and Accumulators" .
2. Check the following items:
–Overrun clutch control valve
–Overrun clutch reducing valve
–Overrun clutch solenoid valve
3. Disassemble A/T. Refer to AT- 2 6 8 , "
Disassembly" .
4. Check the following items:
–Overrun clutch assembly. Refer to AT-320, "Forward and Overrun Clutches" .
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
1. Remove control valve assembly. Refer to AT-242, "
Control Valve Assembly and Accumulators" .
2. Check the following items:
–Overrun clutch control valve
–Overrun clutch reducing valve
–Overrun clutch solenoid valve
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-219
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
2. CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch ON. (Do not start engine)
2. Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. Read out “OVERDRIVE SW”.
Check the signal of the overdrive control switch is indicated
properly.
Without CONSULT-II
1. Turn ignition switch ON. (Do not start engine)
2. Check voltage between A/T device harness connector terminal
and ground. Refer toAT-193, "
Wiring Diagram — AT — NON-
DTC" .
OK or NG
OK >> Go to AT- 2 1 0 , "A/T Does Not Shift: D2 → D3" .
NG >> Check overdrive control switch. Refer to AT - 1 9 1 , "
OVERDRIVE CONTROL SWITCH" .
A/T Does Not Shift: D3 → 22 , When Selector Lever “D” → “2” PositionUCS005VC
SYMPTOM:
A/T does not shift from D3 to 22 when changing selector lever from “D” to “2” position on “Cruise
Test — Part 3”.
DIAGNOSTIC PROCEDURE
1. CHECK SYMPTOM
Check symptom. Refer to AT - 6 1 , "
Cruise Test — Part 1" or AT- 6 4 , "Cruise Test — Part 2" .
Is
“A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2 ” OK?
YES (With CONSULT-II) >>GO TO 2.
YES (Without CONSULT-II) >>GO TO 3.
NO >> Go to AT- 2 0 8 , "
A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2" .
Item nameOverdrive control switch
ConditionDisplay value
OVERDRIVE SWDepressed ON
Released OFF
SCIA4730E
Item Connector TerminalOverdrive
control switch
ConditionJudge-
ment
standard
(Approx.)
A/T device harness
connector (Overdrive
control switch)M38 1 - GroundReleasedBattery
voltage
Depressed 0V
SCIA5336E

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-223
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
6. DETECT MALFUNCTIONING ITEM
1. Remove control valve assembly. Refer to AT-242, "
Control Valve Assembly and Accumulators" .
2. Check the following items:
–Shift valve A
–Shift solenoid valve A
–Overrun clutch control valve
–Overrun clutch solenoid valve
3. Disassemble A/T. Refer to AT- 2 6 8 , "
Disassembly" .
4. Check the following items:
–Servo piston assembly
–Brake band
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
7. CHECK SYMPTOM
Check again. Refer to AT- 6 5 , "
Cruise Test — Part 3" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 8.
8. CHECK TCM
1. Check TCM input/output signals. Refer to AT- 7 8 , "
TCM Terminals and Reference Value" .
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK >>INSPECTION END
NG >> Repair or replace damaged parts.
Vehicle Does Not Decelerate by Engine BrakeUCS005VE
SYMPTOM:

Vehicle does not decelerate by engine brake when shifting from 22 (12 ) to 11 “Cruise Test — Part
3”.

Vehicle does not decelerate by engine brake when OD OFF (OD OFF indicator lamp is on) on
“Cruise Test — Part 3”.

Vehicle does not decelerate by engine brake when shifting A/T from “D” to “2” position on “Cruise
Test — Part 3”.
DIAGNOSTIC PROCEDURE
1. CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to AT-82, "
SELF-DIAGNOSTIC RESULT MODE" or AT-90, "Diagnostic Proce-
dure Without CONSULT-II" .
Is a malfunction in CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT- 9 4 , "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.
SAT7 7 8B

AT-226
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: June 20062007 Versa
5. CHECK A/T POSITION
Check A/T position. Refer to AT-234, "
Checking of A/T Position" .
OK or NG
OK >> GO TO 6.
NG >> Adjust A/T position. Refer to AT- 2 3 3 , "
Adjustment of A/T Position" .
6. CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to AT-107,
"DTC P0720 VEHICLE SPEED SENSOR·A/T (REVOLUTION SENSOR)" and/or AT-166, "DTC VEHICLE
SPEED SENSOR MTR" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace vehicle speed sensor·A/T (revolution sensor) and/or vehicle speed sensor·MTR
circuits.
7. CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to EC-532, "
DTC P2138 APP SENSOR" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace accelerator pedal position sensor.
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-257, "
Components" .
2. Check A/T fluid condition. Refer to AT- 5 3 , "
Fluid Condition Check" .
OK or NG
OK >> GO TO 10.
NG >> GO TO 9.
9. DETECT MALFUNCTIONING ITEM
1. Remove control valve assembly. Refer to AT-242, "
Control Valve Assembly and Accumulators" .
2. Check the following.
–Shift valve A
–Overrun clutch solenoid valve
3. Disassemble A/T. Refer to AT-268, "
Disassembly" .
4. Check the following.
–Overrun clutch assembly. Refer to AT-320, "Forward and Overrun Clutches" .
–Low & reverse brake assembly. Refer to AT-327, "Low & Reverse Brake" .
OK or NG
OK >> GO TO 10.
NG >> Repair or replace damaged parts.
10. CHECK SYMPTOM
Check again. Refer to AT-65, "
Cruise Test — Part 3" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 11.

CVT-2Revision: June 20062007 Versa HOW TO ERASE DTC (WITH GST) ................... 32
Malfunction Indicator Lamp (MIL) ........................... 33
DESCRIPTION .................................................... 33
TROUBLE DIAGNOSIS ............................................ 34
DTC Inspection Priority Chart ................................. 34
Fail-safe .................................................................. 34
FAIL-SAFE FUNCTION ....................................... 34
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 35
INTRODUCTION ................................................. 35
WORK FLOW ...................................................... 36
DIAGNOSTIC WORKSHEET .............................. 37
CVT Electrical Parts Location ................................. 40
Circuit Diagram ....................................................... 42
Inspections before Trouble Diagnosis .................... 43
CVT FLUID CHECK ............................................ 43
STALL TEST ........................................................ 43
LINE PRESSURE TEST ...................................... 45
Road Test ............................................................... 46
DESCRIPTION .................................................... 46
CONSULT-II OPERATION PROCEDURE ........... 47
Check before Engine Is Started .............................. 49
Check at Idle ........................................................... 49
Cruise Test .............................................................. 50
Vehicle Speed When Shifting Gears ...................... 53
TCM Input/Output Signal Reference Values ........... 54
TCM TERMINAL CONNECTOR LAYOUT .......... 54
TCM INSPECTION TABLE .................................. 54
CONSULT-II Function (TRANSMISSION) .............. 57
FUNCTION .......................................................... 57
CONSULT-II REFERENCE VALUE ..................... 57
CONSULT-II SETTING PROCEDURE ................ 59
WORK SUPPORT MODE ................................... 59
SELF-DIAGNOSTIC RESULT MODE ................. 60
DATA MONITOR MODE ...................................... 64
CAN DIAGNOSTIC SUPPORT MONITOR
MODE .................................................................. 66
Diagnostic Procedure without CONSULT-II ............ 67
OBD-II SELF-DIAGNOSTIC PROCEDURE
(WITH GST) ......................................................... 67
DTC U1000 CAN COMMUNICATION LINE .............. 68
Description .............................................................. 68
On Board Diagnosis Logic ...................................... 68
Possible Cause ....................................................... 68
DTC Confirmation Procedure ................................. 68
WITH CONSULT-II .............................................. 68
WITH GST ........................................................... 68
Wiring Diagram — CVT — CAN ............................. 69
Diagnostic Procedure ............................................. 70
DTC U1010 TRANSMISSION CONTROL MODULE
(CAN) ......................................................................... 71
Description .............................................................. 71
On Board Diagnosis Logic ...................................... 71
Possible Cause ....................................................... 71
DTC Confirmation Procedure ................................. 71
WITH CONSULT-II .............................................. 71
WITH GST ........................................................... 71
Diagnostic Procedure ............................................. 71
DTC P0615 START SIGNAL CIRCUIT ..................... 72Description ..............................................................72
CONSULT-II Reference Value .................................72
On Board Diagnosis Logic ......................................72
Possible Cause .......................................................72
DTC Confirmation Procedure ..................................72
WITH CONSULT-II ...............................................72
Wiring Diagram — CVT — STSIG ..........................73
Diagnostic Procedure ..............................................74
DTC P0703 STOP LAMP SWITCH CIRCUIT ............76
Description ..............................................................76
CONSULT-II Reference Value .................................76
On Board Diagnosis Logic ......................................76
Possible Cause .......................................................76
DTC Confirmation Procedure ..................................76
WITH CONSULT-II ...............................................76
Diagnostic Procedure ..............................................77
DTC P0705 PARK/NEUTRAL POSITION SWITCH ...78
Description ..............................................................78
CONSULT-II Reference Value .................................78
On Board Diagnosis Logic ......................................78
Possible Cause .......................................................78
DTC Confirmation Procedure ..................................78
WITH CONSULT-II ...............................................79
WITH GST ...........................................................79
Wiring Diagram — CVT — PNP/SW .......................80
Diagnostic Procedure ..............................................82
Component Inspection ............................................84
PNP SWITCH ......................................................84
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT ....................................................................85
Description ..............................................................85
CONSULT-II Reference Value .................................85
On Board Diagnosis Logic ......................................85
Possible Cause .......................................................85
DTC Confirmation Procedure ..................................85
WITH CONSULT-II ...............................................85
WITH GST ...........................................................85
Wiring Diagram — CVT — FTS ..............................86
Diagnostic Procedure ..............................................87
Component Inspection ............................................89
CVT FLUID TEMPERATURE SENSOR ..............89
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI
SPEED SENSOR) .....................................................90
Description ..............................................................90
CONSULT-II Reference Value .................................90
On Board Diagnosis Logic ......................................90
Possible Cause .......................................................90
DTC Confirmation Procedure ..................................90
WITH CONSULT-II ...............................................90
WITH GST ...........................................................90
Wiring Diagram — CVT — PRSCVT ......................91
Diagnostic Procedure ..............................................92
DTC P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) .....................................95
Description ..............................................................95
CONSULT-II Reference Value .................................95
On Board Diagnosis Logic ......................................95
Possible Cause .......................................................95
DTC Confirmation Procedure ..................................95

TROUBLE DIAGNOSIS
CVT-39
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
44-3.Cruise testCVT-50
❏ CVT-186, "Vehicle Speed Does Not Change in “L” Position"
❏ CVT-187, "Vehicle Speed Does Not Change in overdrive-off mode"
❏ CVT-188, "Vehicle Speed Does Not Change in “D” Position"
❏ CVT-189, "Vehicle Does Not Decelerate by Engine Brake"
❏ perform self-diagnosis. Enter checks for detected items. CVT-60
❏ CVT-68, "DTC U1000 CAN COMMUNICATION LINE"
❏ CVT-72, "DTC P0615 START SIGNAL CIRCUIT"
❏ CVT-76, "DTC P0703 STOP LAMP SWITCH CIRCUIT"
❏ CVT-78, "DTC P0705 PARK/NEUTRAL POSITION SWITCH"
❏ CVT-85, "DTC P0710 CVT FLUID TEMPERATURE SENSOR CIRCUIT"
❏ CVT-90, "DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR)"
❏ CVT-95, "DTC P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED
SENSOR)"
❏ CVT-101, "DTC P0725 ENGINE SPEED SIGNAL"
❏ CVT-103, "DTC P0730 BELT DAMAGE"
❏ CVT-105, "DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE"
❏ CVT-110, "DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)"
❏ CVT-113, "DTC P0745 LINE PRESSURE SOLENOID VALVE"
❏ CVT-118, "DTC P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE
(LINE PRESSURE SOLENOID VALVE)"
❏ CVT-121, "DTC P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE
(SEC PRESSURE SOLENOID VALVE)"
❏ CVT-124, "DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC
PRESSURE SOLENOID VALVE)"
❏ CVT-129, "DTC P0840 TRANSMISSION FLUID PRESSURE SENSOR A CIRCUIT
(SEC PRESSURE SENSOR)"
❏ CVT-134, "DTC P0841 PRESSURE SENSOR FUNCTION"
❏ CVT-137, "DTC P0845 TRANSMISSION FLUID PRESSURE SENSOR B CIRCUIT
(PRI PRESSURE SENSOR)"
❏ CVT-142, "DTC P0868 SECONDARY PRESSURE DOWN"
❏ CVT-145, "DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)"
❏ CVT-150, "DTC P1705 THROTTLE POSITION SENSOR"
❏ CVT-152, "DTC P1722 ESTM VEHICLE SPEED SIGNAL"
❏ CVT-154, "DTC P1723 CVT SPEED SENSOR FUNCTION"
❏ CVT-156, "DTC P1726 ELECTRIC THROTTLE CONTROL SYSTEM"
❏ CVT-158, "DTC P1740 LOCK-UP SELECT SOLENOID VALVE CIRCUIT"
❏ CVT-164, "DTC P1777 STEP MOTOR - CIRCUIT"
❏ CVT-168, "DTC P1778 STEP MOTOR - FUNCTION"
5❏ Inspect each system for items found to be NG in the self-diagnosis and repair or replace the malfunctioning parts.
6❏ Perform all road tests and enter the checks again for the required items.CVT-46
7❏ For any remaining NG items, perform the “diagnosis procedure” and repair or replace the malfunctioning parts.
8❏ Erase the results of the self-diagnosis from the TCM.CVT-32
,
CVT-32

CVT-46
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Line Pressure
*: Reference values
Judgement of Line Pressure Test
Road TestUCS005YC
DESCRIPTION

The purpose of the test is to determine overall performance of
CVT and analyze causes of problems.

The road test consists of the following three parts:
1. “Check Before Engine Is Started” CVT-49
.
2. “Check at Idle” CVT-49
.
3. “Cruise Test” CVT-50
.
Engine speed Line pressure kPa (kg/cm
2 , psi)
“R”, “D” and “L” positions
At idle 650 (6.63, 94.3)
At stall 4,250 (43.35, 616.3)*
Judgement Possible cause
Idle speedLow for all positions
(“P”, “R”, “N”, “D”, “L”)Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example

Oil pump wear

Pressure regulator valve or plug sticking or spring fatigue

Oil strainer
oil pump
pressure regulator valve passage oil leak

Engine idle speed too low
Only low for a specific
positionPossible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
HighPossible causes include a sensor malfunction or malfunction in the line pressure adjustment
function.
For example

Accelerator pedal position signal malfunction

CVT fluid temperature sensor malfunction

Pressure control solenoid A (line pressure solenoid) malfunction (sticking in OFF state, filter
clog, cut line)

Pressure regulator valve or plug sticking
Stall speedLine pressure does
not rise higher than
the line pressure for
idle.Possible causes include a sensor malfunction or malfunction in the pressure adjustment func-
tion.
For example

Accelerator pedal position signal malfunction

TCM malfunction

Pressure control solenoid A (line pressure solenoid) malfunction (shorting, sticking in ON
state)

Pressure regulator valve or plug sticking
The pressure rises,
but does not enter the
standard position.Possible causes include malfunctions in the pressure supply system and malfunction in the
pressure adjustment function.
For example

Accelerator pedal position signal malfunction

Pressure control solenoid A (line pressure solenoid) malfunction (sticking, filter clog)

Pressure regulator valve or plug sticking
Only low for a specific
positionPossible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
SAT7 8 6A

TROUBLE DIAGNOSIS
CVT-47
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa

Before road test, familiarize yourself with all test procedures and
items to check.

Perform tests on all items until specified symptom is found.
Troubleshoot items which check out No Good after road test.
CONSULT-II OPERATION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which performs CAN communication.

Using CONSULT-II, perform a cruise test and record the result.

Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch “MAIN SIGNALS” to set recording condition.
3. See “Numerical Display”, “Barchart Display” or “Line Graph Dis-
play”.
4. Touch “START”.
5. When performing cruise test. Refer to CVT-50, "
Cruise Test" .
6. After finishing cruise test part, touch “RECORD”.
SAT4 9 6G
BCIA0031E
SCIA5493E
SCIA4584E

TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-187
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
Vehicle Speed Does Not Change in overdrive-off modeUCS006KF
SYMPTOM:
Vehicle speed does not change in overdrive-off mode while the cruise test.
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to CVT-60, "
SELF-DIAGNOSTIC RESULT MODE" .
Is any malfunction detected by self-diagnosis?
YES >> Check the malfunctioning system. Refer to CVT-61, "Display Items List" .
NO >> GO TO 2.
2. CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to CVT-170, "
OVERDRIVE CONTROL SWITCH" .
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to CVT-16, "
Checking CVT Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill CVT fluid.
4. CHECK LINE PRESSURE
Check line pressure at idle. Refer to CVT-45, "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 5.
NG >> Check the malfunctioning item. Refer to CVT-46, "
Judgement of Line Pressure Test" .
5. CHECK STALL REVOLUTION
Check stall revolution. Refer to CVT-43, "
STALL TEST" .
OK or NG
OK >> GO TO 6.
NG >> Check the malfunctioning item. Refer to CVT-44, "
Judgement Stall Test" .
6. CHECK SYMPTOM
Check again. Refer to CVT-50, "
Cruise Test" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 7.
7. CHECK TCM
1. Check TCM input/output signals. Refer to CVT-54, "
TCM Input/Output Signal Reference Values" .
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the transaxle assembly. Refer to CVT-207, "Removal and Installation" .
NG >> Repair or replace damaged parts.

COMBINATION METERS
DI-15
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
DATA MONITOR
Display Item List
Display item [Unit]MAIN
SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] X XThe value of vehicle speed signal, which is input from ABS
actuator and electric unit (control unit).
SPEED OUTPUT [km/h] X XThe value of vehicle speed signal, which is transmitted to each
unit with CAN communication.
TACHO METER [rpm] X X The value of engine speed signal, which is input from ECM.
W TEMP METER [°C] X XThe value of engine coolant temperature signal, which is input
from ECM.
FUEL METER [lit.] X XThe value, which processes a resistance signal from fuel
gauge.
DISTANCE [km] X XThe value, which is calculated by vehicle speed signal from
ABS actuator and electric unit (control unit), fuel gauge and
fuel consumption signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
C-ENG W/L [ON/OFF] XIndicates [ON/OFF] condition of malfunction indicator lamp
(MIL).
AIR PRES W/L XIndicates [ON/OFF] condition of low tire pressure warning
lamp.
SEAT BELT W/L X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator lamp.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of KEY warning lamp (green).
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of KEY warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of LOCK warning lamp.
PNP P SW [ON/OFF] X X Indicates [ON/OFF] condition of inhibitor P switch.
PNP N SW [ON/OFF] X X Indicates [ON/OFF] condition of inhibitor N switch.
O/D OFF SW [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF switch.
BRAKE SW [ON/OFF] X Indicates [ON/OFF] condition of parking brake switch.
P RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift P range indi-
cator.
R RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift R range indi-
cator.
N RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift N range indi-
cator.
D RANGE IND [ON/OFF] X XIndicates [ON/OFF] condition of A/T or CVT shift D range indi-
cator.
2 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 2 range indicator.
L RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of CVT shift L range indicator.
1 RANGE IND [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift 1 range indicator.
CRUISE IND [ON/OFF] X Indicates [ON/OFF] condition of CRUISE indicator.
SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator.
O/D OFF W/L [ON/OFF] X Indicates [ON/OFF] condition of O/D OFF indicator lamp.