ATF NISSAN TIIDA 2007 Service Service Manual

AT-352
REPAIR FOR COMPONENT PARTS
Revision: June 20062007 Versa
c. Adjust the back clearance of side gear according to the following
procedures.
i. Insert feeler gauges A of the same thickness to the back of side
gear from both sides, preventing side gear from falling, to mea-
sure the clearance.

Measure clearance 3 times by rotating side gears and take
the average.
CAUTION:
In all 3 measurements, maximize the clearance by aligning
teeth on side gears at the top and bottom at the same posi-
tion.
ii. Select side gear thrust washer so that the clearance will fall
within the standard.
iii. Turn differential case upside down, and measure the back clear-
ance of the other side gear in the same manner.
NOTE:
Adjust the clearance to approx. 0.1 mm (0.004 in) for used differ-
ential [driven approx. 3,000 km (1864 mile) or more].
4. Install lock pin (1) to pinion mate shaft using the pin punch A.
CAUTION:

Do not reuse lock pin.

Make sure that lock pin is flush with differential case.
5. Install speedometer drive gear on differential case.
6. Set drift A [commercial service tool] on differential side bearing
inner race, and press differential side bearing inner race into dif-
ferential case.
CAUTION:
Apply ATF to differential side bearings.
7. Install differential side bearing outer race and differential side
bearing adjusting shim on transaxle case. Refer to AT-354,
"Assembly (1)" . Differential side gear clearance:
Refer to AT-382, "
Final Drive" .
SCIA7061E
Tool number: KV32101000 (J-25689-A)
SCIA7228E
SAT3 1 3D
SCIA8005E

AT-354
ASSEMBLY
Revision: June 20062007 Versa
ASSEMBLYPFP:00000
Assembly (1)UCS005WG
1. Drive each differential side oil seal evenly using a drift (SST and
commercial service tool) so that differential side oil seal pro-
trudes by the dimension “C” or “D” respectively.
(1): LH differential side oil seal
(2): RH differential side oil seal
(A): Transaxle case side
(B): Converter housing side
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
Drift to be used:
2. Install O-ring on governor cap.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
3. Install governor cap in transaxle case.
4. Install snap ring in transaxle case.
5. Install parking actuator support (1) on transaxle case.
(A): Inside
(B): Outside
CAUTION:
Be careful with the direction of parking actuator support (1).
6. Tighten parking actuator support fitting bolts to the specified
torque. Refer to AT-257, "
Components" .
7. Install parking pawl (2) on transaxle case, and fix it with parking
shaft (1).
Dimension “C” 0 ± 0.5 (0 ± 0.020)
Dimension “D” 6 ± 0.5 (0.043 ± 0.020)
SCIA7226E
Location Tool number
Transaxle case side (A)ST35325000 ( – )
KV31103000 (J-38982)
Converter housing side (B)Commercial service tool [Inner diameter: 47 mm (1.85 in), outer
diameter: 54 mm (2.13 in)]
SCIA5910J
SCIA6997E

ASSEMBLY
AT-355
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
8. Install return spring (2) on parking shaft (3) and parking pawl (1)
using a flat-bladed screwdriver.
Adjustment (1)UCS005WH
DIFFERENTIAL SIDE BEARING PRELOAD
1. Select proper thickness of differential side bearing adjusting shim using the following procedures.
a. Install differential side bearing outer race without differential side
bearing adjusting shim on transaxle case.
CAUTION:
Apply ATF to differential side bearing outer race.
b. Install differential side bearing outer race on converter housing.
CAUTION:
Apply ATF to differential side bearing outer race.
c. Place final drive assembly on transaxle case.
d. Tighten converter housing fitting bolts (1) and (2) to the specified
torque. Refer to AT-349, "
Final Drive" .
SCIA6996E
SAT9 4 7DA
Bolt 1 2
Bolt length
[mm (in)]
32.8 (1.291) 40 (1.57)
Number of bolts 10 10
SCIA7970E

AT-358
ASSEMBLY
Revision: June 20062007 Versa

Remove reduction pinion gear from transaxle case.

Measure dimension “D” between the end of reduction pinion
gear and the adjusting shim mating surface of reduction pin-
ion gear.

Measure dimension “D” in at least two places, and take
the average.

Calculate dimension “A”.
e. Measure dimension “E” between the end of idler gear and idler
gear bearing inner race mating surface of idler gear.

Measure dimension “E” in at least two places, and take
the average.
f. Select proper thickness of reduction pinion gear adjusting shim.
Refer to “Parts Information” for reduction pinion gear adjusting
shim selection.
2. Install reduction pinion gear and reduction pinion gear adjusting
shim selected in step 1-f on transaxle case.
CAUTION:
Apply ATF to reduction pinion gear bearing.
3. Press idler gear bearing inner race on idler gear. Refer to AT-
336, "COMPONENTS" .
4. Press idler gear on reduction pinion gear.
CAUTION:

Apply ATF to idler gear bearing.

Press idler gear until idler gear fully contacts reduction
pinion gear bearing adjusting shim.
5. Set manual shaft in “P” position to fix idler gear.
6. Tighten lock nut of idler gear to the specified torque. Refer to AT-257, "
Components" .
CAUTION:
Lock idler gear with parking pawl when tightening lock nut.
7. Measure turning torque of reduction pinion gear.

When measuring turning torque, turn reduction pinion
gear in both directions several times to seat bearing roll-
ers correctly.

If turning torque is out of specification, decrease or
increase thickness of reduction pinion gear adjusting
shim.A = D − (B + C)
SAT3 3 6DA
Proper shim thickness = A − E − 0.05 mm (0.0020 in)*
(*: Bearing preload)
SAT3 3 7D
Turning torque of reduction pinion gear:
Refer to AT-382, "
Reduction Pinion Gear" .
SCIA5651E
SCIA5514E

AT-370
ASSEMBLY
Revision: June 20062007 Versa
4. Install anchor end pin (2) and lock nut (1) on transaxle case.
5. Place brake band on outside of reverse clutch drum.
6. Tighten anchor end pin just enough so that brake band is evenly
fitted on reverse clutch drum.
7. Install bearing race selected in total end play adjustment step on
oil pump cover.
8. Install thrust washer selected in reverse clutch end play adjust-
ment step on oil pump cover.
9. Install O-ring to oil pump assembly.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
10. Install oil pump assembly (1) on transaxle case.
11. Tighten oil pump fitting bolts to the specified torque. Refer to AT-
257, "Components" .
12. Install O-ring to input shaft assembly (high clutch drum).
SCIA6037J
SAT0 3 8D
SCIA3629E
SCIA6036J
SCIA4928E

AT-374
ASSEMBLY
Revision: June 20062007 Versa
26. Install lip seals (1) for band servo oil holes on transaxle case.
27. Install control valve assembly on transaxle case.
a. Install O-ring on terminal body.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
b. Insert manual valve into control valve assembly.
CAUTION:
Be careful not to drop manual valve.
c. Set manual shaft in “N” position.
d. Install control valve assembly on transaxle case while aligning
manual valve (2) with manual plate (1).
e. Install terminal body (2) into transaxle case by pushing it.
f. Install snap ring (1) to terminal body (2).
g. Tighten bolts A , B and C to the specified torque. Refer to AT-257, "
Components" .
SCIA5895J
SCIA3999E
SCIA7090E
SCIA6030J

AT-376
ASSEMBLY
Revision: June 20062007 Versa
30. Install O-ring (3) to turbine revolution sensor (power train revolu-
tion sensor) (1).
31. Install turbine revolution sensor (power train revolution sensor)
(1) to transaxle case (2).
: Bolt (1)
32. Tighten turbine revolution sensor (power train revolution sensor)
fitting bolt to the specified torque. Refer to AT-257, "
Compo-
nents" .
33. Install revolution sensor (1) to transaxle case (2).
34. Tighten revolution sensor fitting bolts to the specified torque.
Refer to AT-257, "
Components" .
: Bolt (2)
CAUTION:
Ensure revolution sensor harness is firmly secured with
bolt.
(1): Revolution sensor
: Bolt (1)
35. Install torque converter.
a. Pour ATF into torque converter.

Approximately 1 liter (1 US qt, 7/8 Imp pt) of fluid is
required for a new torque converter.

When reusing old torque converter, add the same amount
of ATF as was drained.
SCIA7004J
SCIA7170J
SCIA6518J
SAT4 2 8DA

AT-378
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: June 20062007 Versa
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsUCS005WL
*: Refer to MA-11, "RECOMMENDED FLUIDS AND LUBRICANTS" .
Vehicle Speed at Which Gear Shifting OccursUCS005W M

At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed at When Lock-up Occurs/ReleasesUCS005WN
Stall SpeedUCS005WO
Line PressureUCS005WP
EngineMR18DE
Automatic transaxle model RE4F03B
Automatic transaxle assembly Model code number 3CX0D
Transaxle gear ratio1st 2.861
2nd 1.562
3rd 1.000
4th 0.697
Reverse 2.310
Final drive 4.072
Recommended fluidGenuine NISSAN Matic D ATF (Continental U.S. and Alaska) or
Canada NISSAN Automatic Transmission Fluid*
Fluid capacity [ (US qt, Imp qt)]7.9 (8-3/8, 7)
Throttle positionVehicle speed km/h (MPH)
D1 → D2D2 → D3D3 → D4D4 → D3D3 → D2D2 → D1
Full throttle51 - 59
(32 - 37)97 - 105
(60 - 65)154 - 162
(96 - 101)150 - 158
(93 - 98)87 - 95
(54 - 59)40 - 48
(25 - 30)
Half throttle34 - 42
(21 - 26)62 - 70
(39 - 43)124 - 132
(77 - 82)69 - 77
(43 - 48)36 - 44
(22 - 27)19 - 27
(12 - 17)
Throttle position Selector lever positionVehicle speed km/h (MPH)
Lock-up ON Lock-up OFF
2.0/8“D” position 86 - 94 (53 - 58) 59 - 67 (37 - 42)
“D” position (OD OFF) 86 - 94 (53 - 58) 83 - 91 (52 - 57)
Stall revolution (rpm)2,300 - 2,750
Engine speedLine pressure kPa (kg/cm
2 , psi)
“D”, “2” and “1” positions “R” position
Idle speed 500 (5.1, 73) 778 (7.9, 113)
Stall speed 1,173 (12.0, 170) 1,825 (18.6, 265)

CVT-6
INDEX FOR DTC
Revision: June 20062007 Versa
INDEX FOR DTCPFP:00024
Alphabetical Index UCS005XB
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-68
.
*1: These numbers are prescribed by SAE J2012.
*2: Models without ABS does not indicate.
Items
(CONSULT-II screen terms) DTC
Reference page OBD-II Except OBD-II
CONSULT-II
GST*
1 CONSULT-II only
“TRANSMISSION”
A/T TCC S/V FNCTN P0744 P0744 CVT-110
ATF TEMP SEN/CIRC P0710 P0710CVT-85
BELT DAMG — P0730CVT-103
BRAKE SW/CIRC — P0703CVT-76
CAN COMM CIRCUIT U1000 U1000CVT-68
CONTROL UNIT(CAN) U1010 U1010CVT-71
CVT SPD SEN/FNCTN — P1723CVT-154
ENGINE SPEED SIG — P0725CVT-101
ELEC TH CONTROL — P1726CVT-156
ESTM VEH SPD SIG*2— P1722CVT-152
INPUT SPD SEN/CIRC P0715 P0715CVT-90
L/PRESS CONTROL — P1745CVT-163
L/PRESS SOL/CIRC P0745 P0745CVT-113
LU-SLCT SOL/CIRC P1740 P1740CVT-158
PNP SW/CIRC P0705 P0705CVT-78
PRESS SEN/FNCTN — P0841CVT-134
PRS CNT SOL/A FCTN P0746 P0746CVT-118
PRS CNT SOL/B CIRC P0778 P0778CVT-124
PRS CNT SOL/B FCTN P0776 P0776CVT-121
SEC/PRESS DOWN — P0868CVT-142
STARTER RELAY/CIRC — P0615CVT-72
STEP MOTR CIRC P1777 P1777CVT-164
STEP MOTR/FNC P1778 P1778CVT-168
TCC SOLENOID/CIRC P0740 P0740CVT-105
TCM-POWER SUPPLY — P1701CVT-145
TP SEN/CIRC A/T — P1705CVT-150
TR PRS SENS/A CIRC P0840 P0840CVT-129
TR PRS SENS/B CIRC P0845 P0845CVT-137
VEH SPD SEN/CIR AT P0720 P0720CVT-95

INDEX FOR DTC
CVT-7
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
DTC No. Index UCS005XC
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTCs, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-68
.
*1: These numbers are prescribed by SAE J2012.
*2: Models without ABS does not indicate.
DTC
Items
(CONSULT-II screen terms)Reference page OBD-II Except OBD-II
CONSULT-II
GST*
1CONSULT-II only
“TRANSMISSION”
— P0615 STARTER RELAY/CIRCCVT-72
— P0703 BRAKE SW/CIRCCVT-76
P0705 P0705 PNP SW/CIRCCVT-78
P0710 P0710 ATF TEMP SEN/CIRCCVT-85
P0715 P0715 INPUT SPD SEN/CIRCCVT-90
P0720 P0720 VEH SPD SEN/CIR ATCVT-95
— P0725 ENGINE SPEED SIGCVT-101
— P0730 BELT DAMGCVT-103
P0740 P0740 TCC SOLENOID/CIRCCVT-105
P0744 P0744 A/T TCC S/V FNCTNCVT-110
P0745 P0745 L/PRESS SOL/CIRCCVT-113
P0746 P0746 PRS CNT SOL/A FCTNCVT-118
P0776 P0776 PRS CNT SOL/B FCTNCVT-121
P0778 P0778 PRS CNT SOL/B CIRCCVT-124
P0840 P0840 TR PRS SENS/A CIRCCVT-129
— P0841 PRESS SEN/FNCTNCVT-134
P0845 P0845 TR PRS SENS/B CIRCCVT-137
— P0868 SEC/PRESS DOWNCVT-142
— P1701 TCM-POWER SUPPLYCVT-145
— P1705 TP SEN/CIRC A/TCVT-150
— P1722
ESTM VEH SPD SIG*2CVT-152
— P1723 CVT SPD SEN/FNCTNCVT-154
— P1726 ELEC TH CONTROLCVT-156
P1740 P1740 LU-SLCT SOL/CIRCCVT-158
— P1745 L/PRESS CONTROLCVT-163
P1777 P1777 STEP MOTR CIRCCVT-164
P1778 P1778 STEP MOTR/FNCCVT-168
U1000 U1000 CAN COMM CIRCUITCVT-68
U1010 U1010 CONTROL UNIT(CAN)CVT-71