steering NISSAN TIIDA 2007 Service Service Manual

BRAKE TUBE AND HOSE
BR-11
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: June 20062007 Versa
BRAKE TUBE AND HOSEPFP:46300
Hydraulic CircuitEFS006JB
CAUTION:

All tubes and hoses must be free from excessive bending, twisting and pulling.

Make sure there is no interference with other parts when turning steering both clockwise and
counterclockwise.

Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged
part is detected.

Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted surfaces of body, immediately wipe them with cloth and then wash it away
with water.

Do not bend or twist brake hose sharply, or strongly pull it.

When removing components, cover brake line connections so that dirt, dust, or other foreign mat-
ters do not get in.

Refill using recommended brake fluid. Refer to MA-11, "RECOMMENDED FLUIDS AND LUBRI-
CANTS" .

Never reuse drained brake fluid.
1. Front disc brake 2. Brake master cylinder 3. Brake booster
4. Rear drum brake 5. Connector 6.ABS actuator and electric unit (con-
trol unit)
7. Brake tube 8. Brake hose
:Union bolt
:Connector bolt
:Flare nut
18.2 N.m (1.9 kg-m, 13.0 ft-lb) 10.0 N.m (1.0 kg-m, 87.0 in-lb) 16.2 N.m (1.7 kg-m, 12.0 ft-lb)
SFIA3068E

BR-26
FRONT DISC BRAKE
Revision: June 20062007 Versa
5. Check brake for drag.
6. Install tires to the vehicle.
Removal and Installation of Brake Caliper Assembly EFS006JQ
REMOVAL
1. Remove tires from vehicle.
2. Secure disc rotor using wheel nuts.
CAUTION:
Put matching marks on wheel hub assembly and disc rotor, if it is necessary to remove disc rotor.
3. Drain brake fluid. Refer to BR-9, "
Drain and Refill" .
4. Remove union bolt, and then remove brake hose from caliper
assembly.
5. Remove torque member mounting bolts from torque member,
and remove caliper assembly from vehicle.
INSTALLATION
1. Install caliper assembly to vehicle, and tighten mounting bolts to the specified torque. Refer to BR-24,
"Components" .
CAUTION:
Before installing torque member to vehicle, wipe oil and grease on mounting surface of steering
knuckle and torque member.
2. Install brake hose to caliper assembly. Refer to BR-11, "
Hydraulic Circuit" .
3. Refill with new brake fluid and bleed air. Refer to BR-10, "
Bleeding Brake System" .
4. Check front disc brake for drag.
5. Install tires to the vehicle.
Disassembly and Assembly of Brake Caliper Assembly EFS006JR
NOTE:
Do not remove torque member, brake pads, shims and pad retainers, when disassembling or assembling cyl-
inder body.
DISASSEMBLY
1. Remove caliper assembly from vehicle. Refer to BR-26,
"REMOVAL" .
2. Remove sliding pin bolts from cylinder body, and remove pads,
shims and pad retainers from torque member, if necessary.
CAUTION:
When removing pad retainer from torque member, lift the
pad retainer in the direction shown by arrow, so as not to
deform it.
WFIA0524E
SBR5 56 E

PRECAUTIONS
BRC-3
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: June 20062007 Versa
2. Are there any self-diagnostic items, other than those relating to CAN communication system, in the self-
diagnosis results?

If YES, GO TO 3.

If NO, GO TO 4.
3. Based on self-diagnosis results unrelated to CAN communication, carry out the inspection.
4. Malfunctions may be detected in self-diagnosis depending on control units carrying out CAN communica-
tion. Therefore, erase the self-diagnosis results.
5. Diagnose CAN communication system. Refer to LAN-44, "
TROUBLE DIAGNOSIS" .
Precautions for Brake ControlEFS006LA

During ABS operation, the brake pedal may vibrate lightly and a mechanical noise may be heard. This is
normal.

Just after starting the vehicle, the brake pedal may vibrate or motor operating noises may be heard from
engine compartment. This is normal due to the self check operation.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnosis. Besides electrical system inspection, check brake booster operation, brake fluid level, and fluid
leaks.

If incorrect tire sizes or types are installed on the vehicle or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna or related wiring near the control module, ABS function may have a malfunction
or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits or improper wiring.
Precautions for CAN SystemEFS006LB

Do not apply voltage of 7.0V or higher to terminal to be measured.

Maximum open terminal voltage of tester in use must be less than 7.0V.

Before checking harnesses, turn ignition switch OFF and disconnect battery negative cable.

Area to be repaired must be soldered and wrapped with tape.
Make sure that fraying of twisted wire is within 110 mm (4.33 in).

Do not make a bypass connection to repaired area. (If the circuit
is bypassed, characteristics of twisted wire will be lost.)
PKIA0306E
PKIA0307E

CO-1
ENGINE COOLING SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION CO
A
CO
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 2
OPERATION PROCEDURE ................................. 2
Precautions for Liquid Gasket .................................. 2
REMOVAL OF LIQUID GASKET SEALING .......... 2
LIQUID GASKET APPLICATION PROCEDURE ..... 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
OVERHEATING CAUSE ANALYSIS .......................... 5
Troubleshooting Chart .............................................. 5
COOLING SYSTEM .................................................... 7
Cooling Circuit .......................................................... 7
ENGINE COOLANT .................................................... 8
Inspection ................................................................. 8
LEVEL CHECK ..................................................... 8
CHECKING COOLING SYSTEM FOR LEAKS ..... 8
Changing Engine Coolant ........................................ 8
DRAINING ENGINE COOLANT ........................... 8
REFILLING ENGINE COOLANT .......................... 8
FLUSHING COOLING SYSTEM ........................... 9
RADIATOR .................................................................11
Components ............................................................11
Removal and Installation ........................................ 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
INSPECTION AFTER INSTALLATION ............... 12
Checking Radiator Cap .......................................... 13
Checking Radiator .................................................. 13
COOLING FAN ......................................................... 15
Components (Models With A/C) ............................. 15Components (Models Without A/C) ........................ 15
Removal and Installation ........................................ 16
REMOVAL ........................................................... 16
INSTALLATION ................................................... 16
DISASSEMBLY AND ASSEMBLY .......................... 16
DISASSEMBLY ................................................... 16
INSPECTION AFTER DISASSEMBLY ............... 16
ASSEMBLY ......................................................... 16
WATER PUMP .......................................................... 17
Components ........................................................... 17
Removal and Installation ........................................ 17
REMOVAL ........................................................... 17
INSPECTION AFTER REMOVAL ....................... 17
INSTALLATION ................................................... 17
INSPECTION AFTER INSTALLATION ................ 17
THERMOSTAT .......................................................... 18
Components ........................................................... 18
Removal and Installation ........................................ 18
REMOVAL ........................................................... 18
INSPECTION AFTER REMOVAL ....................... 18
INSTALLATION ................................................... 19
INSPECTION AFTER INSTALLATION ................ 19
WATER OUTLET AND WATER CONTROL VALVE ... 20
Components ........................................................... 20
Removal and Installation ........................................ 20
REMOVAL ........................................................... 20
INSPECTION AFTER REMOVAL ....................... 21
INSTALLATION ................................................... 21
INSPECTION AFTER INSTALLATION ................ 22
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 23
Standard and Limit .................................................. 23
CAPACITY ........................................................... 23
THERMOSTAT .................................................... 23
WATER CONTROL VALVE ................................. 23
RADIATOR .......................................................... 23

CO-2Revision: June 2006
PRECAUTIONS
2007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EBS00U8A
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectEBS00U8C
NOTE:

This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT
SYSTEM).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.
Precautions for Liquid GasketEBS00U8B
REMOVAL OF LIQUID GASKET SEALING

After removing nuts and bolts, separate the mating surface, using Tool and remove old liquid gasket seal-
ing.

CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION CVT
A
B
CVT
Revision: June 20062007 Versa INDEX FOR DTC ........................................................ 6
Alphabetical Index .................................................... 6
DTC No. Index ......................................................... 7
PRECAUTIONS .......................................................... 8
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 8
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 8
OPERATION PROCEDURE ................................. 8
Precautions for On Board Diagnostic (OBD) System
of CVT and Engine ................................................... 9
Service After Replacing TCM and Transaxle
Assembly .................................................................. 9
SERVICE AFTER REPLACING TCM AND
TRANSAXLE ASSEMBLY ..................................... 9
PATTERN A .......................................................... 9
PATTERN B .......................................................... 9
PATTERN C .........................................................11
Removal and Installation Procedure for CVT Unit
Connector ................................................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
Precautions ............................................................ 13
Service Notice or Precautions ................................ 13
CVT FLUID COOLER SERVICE ......................... 13
OBD-II SELF-DIAGNOSIS .................................. 14
PREPARATION ......................................................... 15
Special Service Tools ............................................. 15
Commercial Service Tools ...................................... 15
CVT FLUID ............................................................... 16
Checking CVT Fluid ............................................... 16
FLUID LEVEL CHECK ........................................ 16
FLUID CONDITION CHECK ............................... 17
Changing CVT Fluid ............................................... 17
CVT Fluid Cooler Cleaning .................................... 18
CVT FLUID COOLER CLEANING PROCEDURE
... 18
CVT FLUID COOLER DIAGNOSIS PROCE-DURE .................................................................. 19
CVT FLUID COOLER INSPECTION PROCE-
DURE .................................................................. 20
CVT FLUID COOLER FINAL INSPECTION ........ 20
CVT SYSTEM ............................................................ 21
Cross-sectional View - RE0F08A ........................... 21
Control System ....................................................... 22
Hydraulic Control System ....................................... 23
TCM Function ......................................................... 24
CONTROL SYSTEM OUTLINE .......................... 24
CONTROL SYSTEM DIAGRAM ......................... 24
CAN Communication .............................................. 25
SYSTEM DESCRIPTION .................................... 25
Input/Output Signal of TCM .................................... 25
Line Pressure and Secondary Pressure Control .... 26
NORMAL CONTROL .......................................... 26
FEEDBACK CONTROL ...................................... 26
Shift Control ............................................................ 26
“D” POSITION ..................................................... 27
OVERDRIVE-OFF MODE ................................... 27
“L” POSITION ...................................................... 27
DOWNHILL ENGINE BRAKE CONTROL (AUTO
ENGINE BRAKE CONTROL) .............................. 27
ACCELERATION CONTROL .............................. 27
Lock-up and Select Control .................................... 28
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL ............................ 28
Control Valve .......................................................... 29
FUNCTION OF CONTROL VALVE ..................... 29
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 30
Introduction ............................................................. 30
OBD-II Function for CVT System ........................... 30
One or Two Trip Detection Logic of OBD-II ............ 30
ONE TRIP DETECTION LOGIC ......................... 30
TWO TRIP DETECTION LOGIC ......................... 30
OBD-II Diagnostic Trouble Code (DTC) ................. 30
HOW TO READ DTC AND 1ST TRIP DTC ......... 30
HOW TO ERASE DTC ........................................ 31
HOW TO ERASE DTC (WITH CONSULT-II) ....... 32

CVT-8
PRECAUTIONS
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UCS005XD
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectUCS006Y0
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

KEY INTERLOCK CABLE
CVT-203
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
4. Slide the slider (A) toward the casing cap (B) while pressing tabs
(C) on the slider to separate the slider (A) from the adjust holder
(D).
5. Remove the casing cap (B) from the cable bracket on the control
device assembly.
6. Remove the key interlock cable from the key interlock rod (E).
7. Remove steering column cover (upper and lower) and instru-
ment lower finisher. Refer to IP-10, "
INSTRUMENT PANEL
ASSEMBLY" .
8. Pull out the lock plate (A) from the holder (B).
9. Remove the key interlock cable (1) from the key cylinder (2).
10. Remove the clip (A), and then remove the key interlock cable
(1).
INSTALLATION
CAUTION:

Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or inter-
ference with adjacent parts.

After installing key interlock cable to control device assembly, make sure that casing cap and
bracket are firmly secured in their positions.
1. Place the selector lever in the “P” position.
2. Turn ignition switch to “ACC” or “ON” position.
3. Set the key interlock cable (1) to the key cylinder (2).
4. Install the lock plate (A) to the holder (B).
5. Turn ignition switch to “LOCK” position.
SCIA6975E
SCIA6976E
SCIA6973E
SCIA6976E

CVT-204
KEY INTERLOCK CABLE
Revision: June 20062007 Versa
6. Temporarily install the adjust holder (A) to the key interlock rod
(B).
7. Install the casing cap (C) to the cable bracket (D) on the control
device assembly.
CAUTION:

Do not bend or twist key interlock cable excessively
when installing.

After installing key interlock cable to cable bracket (D) on
control device assembly, make sure casing caps (C) is
firmly secured in cable bracket (D) on control device
assembly.

If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb) removing force], replace key interlock
cable.
8. Slide the slider (A) toward the key interlock rod (D) while press-
ing the pull lock (B) down to securely connect the adjust holder
(C) with the key interlock rod (D).
CAUTION:

Do not press tabs when holding slider (A).

Do not apply any side to side force to key interlock rod
(D) when sliding slider (A).
9. Secure the key interlock cable (1) with the clip (A).
10. Install steering column cover (upper and lower) and instrument
lower finisher. Refer to IP-10, "
INSTRUMENT PANEL ASSEM-
BLY" .
11. Install the center console assembly. Refer to IP-10, "
INSTRU-
MENT PANEL ASSEMBLY" .
12. Install the selector lever knob. Refer to CVT-195, "
Selector
Lever Knob Removal and Installation" .
13. Check shift lock system. Refer to CVT-197, "
Description" .
SCIA6188E
SCIA6978E
SCIA6973E

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: June 20062007 Versa DTC Confirmation Procedure ............................... 399
Diagnostic Procedure ........................................... 400
DTC P0456 EVAP CONTROL SYSTEM ................ 406
On Board Diagnosis Logic ................................... 406
DTC Confirmation Procedure ............................... 407
Overall Function Check ........................................ 408
Diagnostic Procedure ........................................... 409
DTC P0460 FUEL LEVEL SENSOR ...................... 415
Component Description ........................................ 415
On Board Diagnostic Logic .................................. 415
DTC Confirmation Procedure ............................... 415
Diagnostic Procedure ........................................... 416
Removal and Installation ...................................... 416
DTC P0461 FUEL LEVEL SENSOR ...................... 417
Component Description ........................................ 417
On Board Diagnostic Logic .................................. 417
Overall Function Check ........................................ 417
Diagnostic Procedure ........................................... 418
Removal and Installation ...................................... 418
DTC P0462, P0463 FUEL LEVEL SENSOR .......... 419
Component Description ........................................ 419
On Board Diagnostic Logic .................................. 419
DTC Confirmation Procedure ............................... 419
Diagnostic Procedure ........................................... 420
Removal and Installation ...................................... 420
DTC P0500 VSS ..................................................... 421
Description ........................................................... 421
On Board Diagnosis Logic ................................... 421
DTC Confirmation Procedure ............................... 421
Overall Function Check ........................................ 422
Diagnostic Procedure ........................................... 422
DTC P0506 ISC SYSTEM ....................................... 423
Description ........................................................... 423
On Board Diagnosis Logic ................................... 423
DTC Confirmation Procedure ............................... 423
Diagnostic Procedure ........................................... 424
DTC P0507 ISC SYSTEM ....................................... 425
Description ........................................................... 425
On Board Diagnosis Logic ................................... 425
DTC Confirmation Procedure ............................... 425
Diagnostic Procedure ........................................... 426
DTC P0605 ECM .................................................... 427
Component Description ........................................ 427
On Board Diagnosis Logic ................................... 427
DTC Confirmation Procedure ............................... 427
Diagnostic Procedure ........................................... 428
DTC P0643 SENSOR POWER SUPPLY ................ 430
On Board Diagnosis Logic ................................... 430
DTC Confirmation Procedure ............................... 430
Wiring Diagram .................................................... 431
Diagnostic Procedure ........................................... 433
DTC P0850 PNP SWITCH ...................................... 436
Component Description ........................................ 436
CONSULT-II Reference Value in Data Monitor Mode
. 436
On Board Diagnosis Logic ................................... 436
DTC Confirmation Procedure ............................... 436
Overall Function Check ........................................ 437Wiring Diagram .....................................................438
Diagnostic Procedure ...........................................439
DTC P1148 CLOSED LOOP CONTROL ................442
On Board Diagnosis Logic ....................................442
DTC P1217 ENGINE OVER TEMPERATURE ........443
System Description ...............................................443
CONSULT-II Reference Value in Data Monitor Mode
.444
On Board Diagnosis Logic ....................................445
Overall Function Check ........................................445
Wiring Diagram .....................................................448
Diagnostic Procedure ...........................................450
Main 13 Causes of Overheating ...........................458
Component Inspection ..........................................459
DTC P1225 TP SENSOR ........................................460
Component Description ........................................460
On Board Diagnosis Logic ....................................460
DTC Confirmation Procedure ...............................460
Diagnostic Procedure ...........................................461
Removal and Installation ......................................461
DTC P1226 TP SENSOR ........................................462
Component Description ........................................462
On Board Diagnosis Logic ....................................462
DTC Confirmation Procedure ...............................462
Diagnostic Procedure ...........................................463
Removal and Installation ......................................463
DTC P1421 COLD START CONTROL ...................464
Description ............................................................464
On Board Diagnosis Logic ....................................464
DTC Confirmation Procedure ...............................464
Diagnostic Procedure ...........................................464
DTC P1564 ASCD STEERING SWITCH ................466
Component Description ........................................466
CONSULT-II Reference Value in Data Monitor Mode
.466
On Board Diagnosis Logic ....................................466
DTC Confirmation Procedure ...............................467
Wiring Diagram .....................................................468
Diagnostic Procedure ...........................................469
Component Inspection ..........................................472
DTC P1572 ASCD BRAKE SWITCH ......................473
Component Description ........................................473
CONSULT-II Reference Value in Data Monitor Mode
.473
On Board Diagnosis Logic ....................................473
DTC Confirmation Procedure ...............................474
Wiring Diagram .....................................................475
Diagnostic Procedure ...........................................476
Component Inspection ..........................................481
DTC P1574 ASCD VEHICLE SPEED SENSOR .....483
Component Description ........................................483
On Board Diagnosis Logic ....................................483
DTC Confirmation Procedure ...............................483
Diagnostic Procedure ...........................................484
DTC P1715 INPUT SPEED SENSOR (TURBINE
REVOLUTION SENSOR) ........................................485
Description ............................................................485
CONSULT-II Reference Value in Data Monitor Mode
.485