remote control NISSAN TIIDA 2007 Service Repair Manual

AUDIO
AV-17
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: June 20062007 Versa
Audio Unit (Mid Level and Premium System) Harness Connector Terminal Lay-
out
EKS00I9N
Terminals and Reference Value for Audio Unit (Mid Level and Premium System)EKS00I9O
WKIA5440E
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symp-
tom
+–Ignition
switchOperation
2 (W) 3 (BR)Audio sound
signal front
LHOutput ONReceive audio
signalNo sound from
front door speaker
LH or tweeter LH.
4 (V) 5 (R)Audio sound
signal rear
LHOutput ONReceive audio
signalNo sound from
rear door speaker
LH or subwoofer
LH.
6 (L)*2 GroundRemote
control AInput ONPress Phone/
End switch0V
Steering wheel
audio controls do
not function Press SEEK UP
switch1.7V
Press VOL UP
switch3.3V
Except for
above5.0V
7 (LG) Ground ACC signal Input ONIgnition switch
ACC or ONBattery voltageSystem does not
work properly.
11 (G) 12 (SB)Audio sound
signal front
RHOutput ONReceive audio
signalNo sound from
front door speaker
RH or tweeter RH.
SKIA0177E
SKIA0177E
SKIA0177E

AV-18
AUDIO
Revision: June 20062007 Versa
13 (LG) 14 (GR)Audio sound
signal rear
RHOutput ONReceive audio
signalNo sound from
rear door speaker
RH or subwoofer
RH.
15 (B)*2 –Remote
control
groundInput – – –Steering wheel
audio controls do
not function
16 (P)*2 GroundRemote
control BInput ONPress Phone/
Send switch0V
Steering wheel
audio controls do
not function Press SEEK
DOWN switch1.7V
Press VOL
DOWN switch3.3V
Except for
above5.0V
18 (SB) GroundVehicle
speed sig-
nal (8–
pulse)Input ONWhen vehicle
speed is
approx. 40 km/h
(25 MPH)Speed sensitive
volume is inopera-
tive.
19 (BR) GroundBattery
powerInput – – Battery voltageSubwoofer will not
work properly.
21 (B)*2 GroundEQ selec-
tion–ON –0V (with mid level)
12V (with premium)Wrong EQ will
cause sub woofer
to be inoperative
22*1 – Shield – – – – –
26 (R)*1 24 (G)Audio sig-
nal sub-
wooferInput – – Audio signalSubwoofer will not
work properly.
28
(BR)*1GroundSubwoofer
amp. ON
signalOutput ON – 12VSubwoofer will not
work properly.
27 (O)*2 –Bluetooth
ONOutput ONAudio unit
sends power
signal to Blue-
tooth control
unit– Mute inoperative
31
(LG)*233 (V)*2 Audio out OutputACC/
ONAudio unit
receives audio
signal from
Bluetooth con-
trol unitBluetooth can not
be heard.
35*2 – Shield – – – – –Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symp-
tom
+–Ignition
switchOperation
SKIA0177E
PKIC0643E
SKIB3609E

AV-54
TELEPHONE
Revision: June 20062007 Versa
Bluetooth Control Unit Harness Connector Terminal LayoutEKS00I9H
Terminals and Reference Value for Bluetooth Control UnitEKS00I9I
LKIA0753E
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symptom
+–Ignition
switchOperation
1 (R) GroundBattery
powerInput – – Battery voltageSystem does not
work properly.
2 (L) Ground ACC power InputACC/
ON–Battery voltageSystem does not
work properly.
3 (LG) Ground IGN power InputON/
START–Battery voltageSystem does not
work properly.
4 (B) – Ground – – – – –
6 – Shield – – – – –
7 (R/W) 8 (R/L) Mic-in signal Input – – –Bluetooth Micro-
phone inoperative.
9 (LG) 10 (V) Audio out OutputACC/
ONBluetooth control
unit sends audio
signalAudio can not be
heard.
11(O) – Mute Output – – 5V Mute inoperative.
12 (W) GroundRemote
control
switch 1InputACC/
ONPress MODE
switch 0V
Steering wheel audio
control switches do
not function. Press SEEK UP
switch0.75V
Press VOL UP
switch2V
Except for above 5V
13 (L) GroundRemote
control
switch 2InputACC/
ONPress POWER
switch 0V
Steering wheel audio
control switches do
not function. Press SEEK
DOWN switch0.75V
Press VOL
DOWN switch2V
Except for above 5V
14 (B) –Remote
control
groundInput – – –Steering wheel audio
control switches do
not function.
SKIB3609E

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (without Intelligent Key)
–Key switch and ignition knob switch (with Intelligent Key)
–Hazard switch
–Door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back door lock assembly
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door key cylinder switch LH

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-23, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-17, "POWER WINDOW SYSTEM" . NOTE

Room lamp timer. Refer to LT- 9 1 , "INTERIOR ROOM LAMP" .

Rear wiper and washer system. Refer to WW-30, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security (theft warning) system. Refer to BL-193, "VEHICLE SECURITY (THEFT WARNING)
SYSTEM" .

NVIS(NATS) system. Refer to BL-212, "NATS (Nissan Anti-Theft System)" .

Headlamp, tail lamp and battery saver control systems. Refer to LT- 7 5 , "PARKING, LICENSE PLATE AND
TA I L L A M P S" , LT- 5 , "HEADLAMP (FOR USA)" or LT-27, "HEADLAMP (FOR CANADA) - DAYTIME
LIGHT SYSTEM -" .

Front fog lamp. Refer to LT-41, "FRONT FOG LAMP" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-50, "REAR WINDOW DEFOGGER" .
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER

Warning chime. Refer to DI-47, "WARNING CHIME" .

Turn signal and hazard warning lamps. Refer to LT- 5 1 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT

Intelligent Key system. Refer to BL-80, "INTELLIGENT KEY SYSTEM" .

BCS-8
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
MAJOR COMPONENTS AND CONTROL SYSTEM
CAN Communication System DescriptionEKS00I82
Refer to LAN-4, "SYSTEM DESCRIPTION" .
System Input Output
Remote keyless entry systemRemote keyless entry receiver
(keyfob)

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Intelligent Key system Intelligent Key unit

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Power door lock systemFront power door lock/unlock
switch (LH, RH)All door locking actuators
Power supply (IGN) to power window Ignition power supply Power supply to power window system
Power supply (BAT) to power window Battery power supply Power supply to power window system
Panic alarm

Key switch

KeyfobIPDM E/R
Battery saver control

Ignition switch

Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Keyfob

Main power window and door
lock/unlock switch

Front door switch LH

All door switchInterior room lamp
Key warning chime

Key switch

Front door switch LHCombination meter (warning buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LHCombination meter (warning buzzer)
Seat belt warning chime

Seat belt buckle switch LH

Ignition switchCombination meter (warning buzzer)
Front wiper and washer system

Combination switch

Ignition switchIPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Rear wiper and washer system

Combination switch

Ignition switchRear wiper motor
A/C switch signal Front air control ECM
Blower fan switch signal Front air control ECM
A/C indicator signal Front air control A/C indicator
Low tire pressure warning system Remote keyless entry receiver Combination meter

BCS-12
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
Terminals and Reference Values for BCMEKS00I85
Te r m i n a lWire
colorSignal nameSignal
input/
outputMeasuring condition
Reference value or waveform
(Approx.) Ignition
switchOperation or condition
2BRCombination switch
input 5Input ONLighting, turn, wiper OFF
Wiper dial position 4
3GRCombination switch
input 4Input ONLighting, turn, wiper OFF
Wiper dial position 4
4LCombination switch
input 3Input ONLighting, turn, wiper OFF
Wiper dial position 4
5GCombination switch
input 2
Input ONLighting, turn, wiper OFF
Wiper dial position 4
6VCombination switch
input 1
7BRFront door key cylin-
der switch LH (unlock)Input
OFFON (open, 2nd turn) Momentary 1.5V
OFF (closed) 0V
8YFront door key cylin-
der switch LH (lock)InputOn (open) Momentary 1.5V
OFF (closed) 0V
9WRear window defog-
ger switchInput ONRear window defogger switch
ON0V
Rear window defogger switch
OFF5V
11 LIgnition switch (ACC
or ON)InputACC or
ONIgnition switch ACC or ON Battery voltage
12 SB Front door switch RH Input OFFON (open) 0V
OFF (closed) Battery voltage
13 GR Rear door switch RH Input OFFON (open) 0V
OFF (closed) Battery voltage
15 WTire pressure warning
check connectorInput OFF — 5V
18 VRemote keyless entry
receiver (ground)Output OFF — 0V
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E

BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
19 BRRemote keyless entry
receiver (power sup-
ply)Output OFF Ignition switch OFF
20 GRemote keyless entry
receiver signal (sig-
nal)Input OFFStand-by (keyfob buttons
released)
When remote keyless entry
receiver receives signal from
keyfob (keyfob buttons
pressed)
21 P NATS antenna amp.Input/
OutputOFF →
ONIgnition switch (OFF → ON)Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then
return to battery voltage.
23 RSecurity indicator
lampOutput OFFGoes OFF → illuminates
(Every 2.4 seconds)Battery voltage → 0V
25 LG NATS antenna amp.Input/
OutputOFF →
ONIgnition switch (OFF → ON)Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then
return to battery voltage.
26 GR Thermo control amp. Input ON A/C switch ON
27 OCompressor ON sig-
nalInput ONA/C switch OFF 5V
A/C switch ON 0V
28 P Front blower monitor Input ONFront blower motor OFF Battery voltage
Front blower motor ON 0V
29 L Hazard switch Input OFFON 0V
OFF 5V
30
*1VBack door open out-
putOutput —Back door open (switch
closed)0V
Back door closed (switch
open)5V
30
*2VBack door opener
switchInput —All doors locked (SW OFF) Battery voltage
All doors unlocked (SW ON) 0V TerminalWire
colorSignal nameSignal
input/
outputMeasuring condition
Reference value or waveform
(Approx.) Ignition
switchOperation or condition
LIIA1893E
LIIA1894E
LIIA1895E
ZJIA0719J

BCM (BODY CONTROL MODULE)
BCS-17
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
CONSULT-II Function (BCM)EKS00I87
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
BCM diagnostic
test itemDiagnostic mode Content
Inspection by partWORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
MNTRThe results of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
System and itemCONSULT-II dis-
playDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSCAN DIAG
SUPPORT
MNTRDATA
MONITORECU
PA R T
NUMBERACTIVE
TESTCON-
FIGU-
RATION
BCM BCM×× × × ×
Power door lock sys-
temDOOR LOCK×××
Rear defoggerREAR DEFOG-
GER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remote keyless entry
systemMULTI REMOTE
ENT×××
Headlamp HEAD LAMP×××
Wiper WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch sig-
nal
Air conditioner switch
signalAIR CONDI-
TIONER×
Intelligent KeyINTELLIGENT
KEY×
Combination switch COMB SW×
NVIS (NATS) IMMU××
Interior lamp battery
saverBATTERY
SAVER×××
Back door TRUNK××
Theft alarm THEFT ALARM×××
Retained accessory
power controlRETAINED PWR×××

REMOTE KEYLESS ENTRY SYSTEM
BL-55
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
System DescriptionEIS0091A
INPUTS
Power is supplied at all times

through 40A fusible link (letter g , located in the fuse and fusible link box)

to BCM terminal 70

through 10A fuse [No. 8, located in the fuse block (J/B)]

to BCM terminal 57.
When the key switch is ON (key is inserted in ignition key cylinder), power is supplied

through 10A fuse [No. 14, located in the fuse block (J/B)]

through key switch terminals 2 and 1

to BCM terminal 37.
When the ignition switch is ACC or ON, power is supplied

through 10A fuse [No. 20, located in the fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 67

through body grounds M57 and M61.
When the front door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 47

through front door switch LH terminal 2

through front door switch LH case ground.
When the front door switch RH is ON (door is OPEN), ground is supplied

to BCM terminal 12

through front door switch RH terminal 2

through front door switch RH case ground.
When the rear door switch LH is ON (door is OPEN), ground is supplied

to BCM terminal 48

through rear door switch LH terminal 1

through rear door switch LH case ground.
When the rear door switch RH is ON (door is OPEN), ground is supplied

to BCM meter terminal 13

through rear door switch RH terminal 1

through rear door switch RH case ground.
When the back door lock assembly (back door switch) is ON (back door is OPEN), ground is supplied

to BCM terminal 43

through back door lock assembly (back door switch) terminals 3 and 4

through body grounds B117, B132 and D402.
Keyfob signal is inputted to BCM from remote keyless entry receiver.
The remote keyless entry system controls operation of the

power door lock

hazard reminder

auto door lock

panic alarm

room lamp

BL-76
REMOTE KEYLESS ENTRY SYSTEM
Revision: June 20062007 Versa
ID Code Entry ProcedureEIS0091S
KEYFOB ID SET UP WITH CONSULT-II
NOTE:

If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A
specific ID code can be erased with CONSULT-II. However, when the ID code of a lost keyfob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new keyfobs must be re-registered.

When registering an additional keyfob, the existing ID codes in memory may or may not be erased.
If five ID codes are stored in memory, when an additional code is registered, only the oldest code
is erased. If less than five ID codes are stored in memory, when an additional ID code is registered,
the new ID code is added and no ID codes are erased.

Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest
ID code will be erased.

Even if same ID code that is already in the memory is input, the same ID code can be entered. The
code is counted as an additional code.
1. Refer to GI-38, "
CONSULT-II Start Procedure" .
2. Touch “MULTI REMOTE ENT”.
3. Touch “WORK SUPPORT”.
4. The items are shown on the figure can be set up.

“REMO CONT ID CONFIR”
Use this mode to confirm if a keyfob ID code is registered or
not.

“REMO CONT ID REGIST”
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or
when additional keyfob is required.

“REMO CONT ID ERASUR”
Use this mode to erase a keyfob ID code.
PIIB0596E
BCIA0031E
LIIA0207E