engine control NISSAN TIIDA 2007 Service Repair Manual

ROAD TEST
TM-485
< ON-VEHICLE MAINTENANCE >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Move selector lever to “D”, “2” and “1” positions and check if vehicle
creeps forward.
Does vehicle creep forward in all three positions?
YES >> GO TO TM-485, "Cruise Test - Part 1".
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-144, "
Vehicle Does Not Creep Forward in
"D", "2" or "1" Position".
 Continue “Road Test”.
Cruise Test - Part 1INFOID:0000000001726685
1.CHECK STARTING GEAR (D1) POSITION
1. Drive vehicle for approximately 10 minutes to warm engine oil and ATF up to operating temperature.
2. Park vehicle on flat surface.
3. Push overdrive control switch. (OD OFF indicator lamp is off.)
4. Move selector lever to “P” position.
5. Start engine.
6. Move selector lever to “D” position.
7. Accelerate vehicle by constantly depressing accelerator pedal
half-way.
Read gear position. Refer to XX-XX, "*****"
.
Does vehicle start from D
1?
YES >> GO TO 2.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-145, "
Vehicle Cannot Be Started from D1".
 Continue “Road Test”.
2.CHECK SHIFT-UP (D1 TO D2)
Check shift-up (D
1 to D2).
Specified speed when shifting from D
1 to D2. Refer to TM-490, "Vehicle Speed When Shifting Gears".
SAT773B
ATF operating temperature: 50 - 80°C (122 - 176°F)
SCIA5472E
SAT775B
SAT495G

ROAD TEST
TM-487
< ON-VEHICLE MAINTENANCE >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
When lock-up duty becomes 94%. Refer to XX-XX, "*****".
Does A/T hold lock-up condition for more than 30 seconds?
YES >> GO TO 7.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-151, "
A/T Does Not Hold Lock-up Condition".
 Continue “Road Test”.
7.CHECK SHIFT-DOWN (D4L/U TO D4)
Release accelerator pedal.
When lock-up duty becomes 4%. Refer to XX-XX, "*****"
.
Is lock-up released when accelerator pedal is released?
YES >> GO TO 8.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-152, "
Lock-up Is Not Released".
 Continue “Road Test”.
8.CHECK SHIFT-DOWN (D4 TO D3)
Decelerate vehicle by applying foot brake lightly.
Read gear position and engine speed. Refer to XX-XX,
"*****".
Does engine speed return to idle smoothly when A/T is shifted from
D4 to D3?
YES >> 1. Stop vehicle.
2. Go to TM-487, "
Cruise Test - Part 2".
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-153, "
Engine Speed Does Not Return to
Idle (Light Braking D4→ D3)".
 Continue “Road Test”.
Cruise Test - Part 2INFOID:0000000001726686
1.CHECK STARTING GEAR (D1) POSITION
1. Push overdrive control switch. (OD OFF indicator lamp is off.)
2. Move selector lever to “D” position.
3. Accelerate vehicle by half throttle again.
Read gear position. Refer to XX-XX, "*****"
.
Does vehicle start from D
1?
YES >> GO TO 2.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-145, "
Vehicle Cannot Be Started from D1".
 Continue “Road Test”.
2.CHECK SHIFT-UP AND SHIFT-DOWN (D3 TO D4 TO D2)
1. Accelerate vehicle to 80 km/h (50 MPH) as shown in the figure.
SAT959I
SAT495G

TM-488
< ON-VEHICLE MAINTENANCE >[TYPE 2 (4AT: RE4F03B)]
ROAD TEST
2. Release accelerator pedal and then quickly depress it fully.
Read gear position and throttle opening. Refer to XX-XX,
"*****".
Does A/T shift from D
4 to D2 as soon as accelerator pedal is
depressed fully?
YES >> GO TO 3.
NO >>  Mark the box on the XX-XX, "*****"
.
GO TO TM-146, "
A/T Does Not Shift: D1→ D2or Does
Not Kickdown: D4→ D2".
 Continue “Road Test”.
3.CHECK SHIFT-UP (D2 TO D3)
Check shift-up (D
2 to D3)
Specified speed when shifting from D
2 to D3. Refer to TM-490, "Vehicle Speed When Shifting Gears".
Read gear position, throttle opening and vehicle speed.
Refer to XX-XX, "*****"
.
Does A/T shift from D
2 to D3 at the specified speed?
YES >> GO TO 4.
NO >>  Mark the box on the XX-XX, "*****"
.
GO TO TM-148, "
A/T Does Not Shift: D2→ D3".
 Continue “Road Test”.
4.CHECK SHIFT-UP (D3 TO D4) AND ENGINE BRAKE
Release accelerator pedal after shifting from D
2 to D3.
Read gear position, throttle opening and vehicle speed.
Refer to XX-XX, "*****"
.
Does A/T shift from D
3 to D4 and does vehicle decelerate by engine
brake?
YES >> 1. Stop vehicle.
2. Go to TM-488, "
Cruise Test - Part 3".
NO >>  Mark the box on the XX-XX, "*****"
.
GO TO TM-149, "
A/T Does Not Shift: D3→ D4".
 Continue “Road Test”.
Cruise Test - Part 3INFOID:0000000001726687
1.CHECK SHIFT-DOWN (D4 TO D3) (WITH OVERDRIVE CONTROL SWITCH)
1. Push overdrive control switch. (OD OFF indicator lamp is off.)
2. Move selector lever to “D” position.
3. Accelerate vehicle using half throttle to D
4.
SCIA7192E
SAT960I
SAT405H
SAT812A

ROAD TEST
TM-489
< ON-VEHICLE MAINTENANCE >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
4. Release accelerator pedal.
5. Push overdrive control switch. (OD OFF indicator lamp is on.)
Read gear position and vehicle speed. Refer to XX-XX,
"*****".
Does A/T shift from D
4 to D3 (OD OFF)?
YES >> GO TO 2.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-154, "
A/T Does Not Shift: D4→ D3, When
OD OFF".
 Continue “Road Test”.
2.CHECK ENGINE BRAKE
Check engine brake.
Does vehicle decelerate by engine brake?
YES >> GO TO 3.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-158, "
Vehicle Does Not Decelerate by
Engine Brake".
 Continue “Road Test”.
3.CHECK SHIFT-DOWN (D3 TO 22)
Move selector lever from “D” to “2” position while driving in D
3 (OD
OFF).
Read gear position. Refer to XX-XX, "*****"
.
Does A/T shift from D
3 (OD OFF) to 22?
YES >> GO TO 4.
NO >>  Mark the box on the XX-XX, "*****"
.
 GO TO TM-155, "
A/T Does Not Shift: D3→ 22, When
Selector Lever "D" → "2" Position" .
 Continue “Road Test”.
4.CHECK ENGINE BRAKE
SAT813A
SCIA5469E
SCIA5469E
SAT791GA

SHIFT CONTROL SYSTEM
TM-497
< ON-VEHICLE REPAIR >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
1. Place the selector lever knob (1) in “N” position.
2. Slide knob cover (2) downward.
3. Pull out lock pin (3) from selector lever knob (1).
4. Remove selector lever knob (1) and knob cover (2) as a set from
selector lever.
CAUTION:
Do not push selector button.
INSTALLATION
1. Insert lock pin (1) to selector lever knob (2).
2. Install knob cover (3) to selector lever knob (2).
3. Place the selector lever in “N” position.
4. Install selector lever knob over selector lever until a click is felt.
CAUTION:
 Do not tilt selector lever knob when installing. Install it
straight, and do not tap or apply any shock to install it.
 Do not push selector button.
Adjustment of A/T PositionINFOID:0000000001731424
Move selector lever from “P” position to “1” position. You should be able to feel the detents in each position. If
the detents cannot be felt or if the position indicator is improperly aligned, the control cable needs adjustment.
CAUTION:
Make sure that parking brake is applied before adjustment.
1. Remove the air duct assembly. Refer to EM-27, "
Removal and Installation".
2. Remove the control cable nut (A) and control cable (1) and
place the manual lever (2) in the "P' position.
3. Place selector lever in “P” position.
4. Hold control cable (1) at the end and pull it with a force of 9.8 N
(approximately 1 kg, 2.2 lb). Release the control cable and tem-
porarily tighten control cable nut (A).
5. Tighten control cable nut (A) to the specified torque.
CAUTION:
Secure manual lever when tightening nut.
6. Move selector lever from “P” to “1” position again. Make sure that selector lever moves smoothly.
7. Check A/T position. Refer to TM-497, "
Checking of A/T Position".
8. Install air duct assembly. Refer to EM-27, "
Removal and Installation".
Checking of A/T PositionINFOID:0000000001731425
1. Place selector lever in “P” position, and turn ignition switch ON (Do not start engine).
2. Make sure selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
make sure selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm selector lever stops at each position with the feel of engagement when it is moved through all the
positions. Check whether or not the actual position selector lever is in matches the position shown by the
shift position indicator and the transaxle.
SCIA6971E
SCIA6972E
Control cable nut : Refer to TM-493, "Control De-
vice Removal and Installation".WCIA0635E

TM-498
< ON-VEHICLE REPAIR >[TYPE 2 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
5. The method of operating selector lever to individual positions
correctly should be as shown.
 (A): Press selector button to operate selector lever, while
depressing the brake pedal.
 (B): Press selector button to operate selector lever.
 (C): Selector lever can be operated without pressing selector
button.
6. Confirm back-up lamps illuminate only when selector lever is
placed in “R” position. Confirm back-up lamps do not illuminate
when selector lever is in “P” or “N” position even if it is pushed
toward “R” position without pressing selector button.
7. Confirm engine can only be started with selector lever in “P” and
“N” positions.
8. Make sure A/T is locked completely in “P” position.
WCIA0636E

VTL-38
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
A/C UNIT ASSEMBLY
7. Remove console box assembly. Refer to IP-11, "Removal and Installation" .
8. Remove instrument stay nuts (A) and harness clamps (B), and
then remove instrument stay (1).
9. Disconnect thermo control amp. connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-48, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-48, "
Removal and Installation".
13. Remove side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable.
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Changing Engine
Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant.
CAUTION:
 Replace O-rings for A/C piping with new ones, and apply compressor oil when installing.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0647E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : Refer to ST-9, "
Removal and Installation".

WCS-56
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE)
Reference ValueINFOID:0000000001728312
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
AIR COND SWA/C switch OFF OFF
A/C switch ON ON
AUT LIGHT SYSOutside of the room is dark OFF
Outside of the room is bright ON
AUTO LIGHT SWLighting switch OFF OFF
Lighting switch AUTO ON
BACK DOOR SWBack door closed OFF
Back door opened ON
BATTERY VOLT
NOTE:
Diesel engine models
onlyIgnition switch ONApproximately the same as power
supply voltage
CDL LOCK SWDoor lock/unlock switch does not operate OFF
Press door lock/unlock switch to the LOCK side ON
CDL UNLOCK SWDoor lock/unlock switch does not operate OFF
Press door lock/unlock switch to the UNLOCK side ON
DOOR SW-ASPassenger door closed OFF
Passenger door opened ON
DOOR SW-DRDriver door closed OFF
Driver door opened ON
DOOR SW-RLRear LH door closed OFF
Rear LH door opened ON
DOOR SW-RRRear RH door closed OFF
Rear RH door opened ON
ELEC PWR CUT
NOTE:
Diesel engine models
onlyEngine runningFan switch ON (when engine coolant is
cool)
NOTE:
Depending on the ambient tempera-
ture, battery voltage, etc.OFF
The current status maintained with the
signal from ECM received.FREEZ
 Fan switch OFF
 Fan switch ON after engine warming
UP
NOTE:
Depending on the engine coolant
temperature, ambient temperature,
battery voltage, etc.INHBT
ENG COOLNT T
NOTE:
Diesel engine models
onlyEngine runningApproximately the same as engine
water temperature
ENGINE RPM
NOTE:
Diesel engine models
onlyEngine runningApproximately the same as tachom-
eter reading

WCS
BCM (BODY CONTROL MODULE)
WCS-57
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ENGINE RUNEngine stopped OFF
Engine running ON
ENGINE STATUS
NOTE:
Diesel engine models
onlyEngine stopped STOP
While the engine stalls STALL
Engine running RUN
At engine cranking CRA
FA N O N S IGFan switch OFF OFF
Fan switch ON ON
FR FOG SWFront fog lamp switch OFF OFF
Front fog lamp switch ON ON
FR WASHER SWFront washer switch OFF OFF
Front washer switch ON ON
FR WIPER LOWFront wiper switch OFF OFF
Front wiper switch LO ON
FR WIPER HIFront wiper switch OFF OFF
Front wiper switch HI ON
FR WIPER INTFront wiper switch OFF OFF
Front wiper switch INT ON
FR WIPER STOPAny position other than front wiper stop position OFF
Front wiper stop position ON
HAZARD SWWhen hazard switch is not pressed OFF
When hazard switch is pressed ON
LIGHT SW 1STLighting switch OFF OFF
Lighting switch 1st ON
H/L SW POSHeadlamp switch OFF OFF
Headlamp switch 1st ON
HI BEAM SWHigh beam switch OFF OFF
High beam switch HI ON
HOOD SWClose the hood
NOTE:
Vehicles without theft warning system are OFF-fixedOFF
Open the hood ON
H/L WASH SWNOTE:
The item is indicated, but not monitoredOFF
IGN ON SWIgnition switch OFF or ACC OFF
Ignition switch ON ON
IGN SW CANIgnition switch OFF or ACC OFF
Ignition switch ON ON
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1 - 7
I-KEY LOCK
1LOCK button of Intelligent Key is not pressed OFF
LOCK button of Intelligent Key is pressed ON
I-KEY UNLOCK
1UNLOCK button of Intelligent Key is not pressed OFF
UNLOCK button of Intelligent Key is pressed ON
KEY SW
2Mechanical key is removed from key cylinder OFF
Mechanical key is inserted to key cylinder ON Monitor Item Condition Value/Status

WCS-58
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
1: With Intelligent Key
2: With remote keyless entry system
3: HatchbackKEYLESS LOCK
2LOCK button of key fob is not pressed OFF
LOCK button of key fob is pressed ON
KEYLESS UNLOCK
2UNLOCK button of key fob is not pressed OFF
UNLOCK button of key fob is pressed ON
LIT-SEN FAILLight & rain sensor is in normal condition OK
Light & rain sensor is with internal error NOTOK
OIL PRESS SW Ignition switch OFF or ACC
 Engine runningOFF
Ignition switch ON ON
OUT SIDE TEMP
NOTE:
Diesel engine modelsIgnition switch ONApproximately the same as outside
air temperature
PASSING SWOther than lighting switch PASS OFF
Lighting switch PASS ON
PUSH SW
1Return to ignition switch to LOCK position OFF
Press ignition switch ON
REAR DEF SWRear window defogger switch OFF OFF
Rear window defogger switch ON ON
RKE LOCK AND
UNLOCK
2NOTE:
The item is indicated, but not monitoredOFF
ON
RR FOG SWRear fog lamp switch OFF OFF
Rear fog lamp switch ON ON
RR WASHER SW
3Rear washer switch OFF OFF
Rear washer switch ON ON
RR WIPER INT
3Rear wiper switch OFF OFF
Rear wiper switch INT ON
RR WIPER ON
3 Rear wiper switch OFF OFF
Rear wiper switch ON ON
RR WIPER STOP
3Rear wiper stop position OFF
Other than rear wiper stop position ON
TAIL LAMP SWLighting switch OFF OFF
Lighting switch 1ST ON
TRNK OPNR SWWhen back door opener switch is not pressed OFF
When back door opener switch is pressed ON
TURN SIGNAL LTurn signal switch OFF OFF
Turn signal switch LH ON
TURN SIGNAL RTurn signal switch OFF OFF
Turn signal switch RH ON
UNLOCK WITH DRNOTE:
The item is indicated, but not monitoredOFF
ON
VEHICLE SPEED While driving Equivalent to speedometer reading Monitor Item Condition Value/Status