key fob NISSAN TIIDA 2007 Service Repair Manual

BCS
DIAGNOSIS SYSTEM (BCM)
BCS-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
BCM : CONSULT-III Function (BCM - BCM)INFOID:0000000001451464
WORK SUPPORT
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)INFOID:0000000001451465
WORK SUPPORT
DATA MONITOR
1: With Intelligent Key
2: With remote keyless entry system
ACTIVE TEST
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
Work Item Description
SECURITY DOOR LOCK SETAnti hijack function mode can be changed in this mode.
 ON: Anti hijack mode is active.
 OFF: Anti hijack mode is inactive.
AUTO LOCK SETAuto door lock time can be changed in this mode.
 MODE 1: 1 minute
 MODE 2: 2 minutes
 MODE 3: 3 minutes
 MODE 4: 4 minutes
 MODE 5: 5 minutes
Monitor Item
[Unit}Description
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.
PUSH SW
1 [ON/OFF]Indicates condition of ignition knob switch.
KEY SW
2 [ON/OFF]Indicates condition of key switch.
CDL LOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
CDL UNLOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
DOOR SW-DR [ON/OFF] Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF] Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH.
DOOR SW-RL [ON/OFF] Indicates condition of rear door switch LH.
TRNK OPNR SW [ON/OFF] Indicates condition of back door switch.
BACK DOOR SW [ON/OFF] Indicates condition of back door switch.
KEYLESS LOCK
2 [ON/OFF]Indicates condition of lock signal from key fob.
KEYLESS UNLOCK
2 [ON/OFF]Indicates condition of unlock signal from key fob.
I-KEY LOCK
1 [ON/OFF]Indicates condition of lock signal from Intelligent Key.
I-KEY UNLOCK
1 [ON/OFF]Indicates condition of unlock signal from Intelligent Key.
Test item Description
DOOR LOCKThis test is able to check door lock operation [ALL LOCK/ALL UNLOCK/DR UNLOCK/
OTHER UNLOCK].
SUPER LOCK
*This test is able to check super lock operation [LOCK (SET)/UNLOCK (RELEASE)].

BCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)INFOID:0000000001451470
WORK SUPPORT
*: Initial setting
DATA MONITOR
Work Item Description
HAZARD LAMP SETAnswer back function (hazard) mode can be changed in this mode.
For the detail of the setting, refer to DLK-617, "
REMOTE KEYLESS ENTRY : System Descrip-
tion".
AUTO LOCK SETAuto door lock time can be changed in this mode.
 MODE 1: 1 minute
 MODE 2: 2 minutes
 MODE 3: 3 minutes
 MODE 4: 4 minutes
 MODE 5: 5 minutes
Monitor Item
[Unit}Condition
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.
KEY SW [ON/OFF] Indicates condition of key switch.
KEYLESS LOCK [ON/OFF] Indicates condition of lock signal from keyfob.
KEYLESS UNLOCK [ON/OFF] Indicates condition of unlock signal from keyfob.
DOOR SW-DR [ON/OFF] Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF] Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH.
DOOR SW-RL [ON/OFF] Indicates condition of rear door switch LH.
BACK DOOR SW [ON/OFF] Indicates condition of back door switch.
CDL LOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
CDL UNLOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
RKE LOCK AND UNLOCK This item is indicated, but not monitored.
Test Item Description
DOOR LOCKThis test is able to check warning chime in combination meter operation. [ALL LOCK/ALL UN-
LOCK/DR UNLOCK/OTHER UNLOCK]
INT LAMP This test is able to check interior lamp operation [ON/OFF].
FLASHER This test is able to check flasher operation [LH/RH/OFF].
Work item Setting Description
BATTERY SAVER SETON*
Battery saver mode can be changed.
OFF
Monitor item
[Unit]Description
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)

BCS-22
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
1: Factory setting
2: If equipped
DATA MONITOR
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)INFOID:0000000001451472
WORK SUPPORT
DATA MONITOR
Monitor Item
[Unit]Description
IGN ON SW [ON/OFF] Ignition switch ON status judged from ignition power supply.
FR WIPER HI [ON/OFF]
Each switch status that BCM judges from the combination switch reading function. FR WIPER LOW [ON/OFF]
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7] Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP [ON/OFF]Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion.
VEHICLE SPEED [km/h]The value of the vehicle speed signal received from combination meter with CAN com-
munication.
H/L SW POS [ON/OFF]
RR WIPER ON [ON/OFF]
Each switch status that BCM judges from the combination switch reading function. RR WIPER INT [ON/OFF]
RR WASHER SW [ON/OFF]
RR WIPER STOP [ON/OFF] Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN [ON/OFF] Transmission reverse position moitored via CAN.
Test Item Operation Description
HEADLAMP WASH-
ERONTransmits the headlamp washer request signal to IPDM E/R with CAN communication to
operate the headlamp washer operation.
FR WIPERHITransmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LOTransmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INTTransmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPERON Outputs the voltage to operate the rear wiper motor.
OFF Stops the voltage to stop.
Work Item Description
HAZARD LAMP SETOperation MODE1 MODE2 MODE3
MODE4
Keyfob operation Lock Unlock Lock Unlock Lock Unlock Lock Unlock
Hazard lamp flash - - - Twice Once - Once Twice

BCS
BCM (BODY CONTROL MODULE)
BCS-37
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
I-KEY UNLOCK1UNLOCK button of Intelligent Key is not pressed OFF
UNLOCK button of Intelligent Key is pressed ON
KEY SW
2Mechanical key is removed from key cylinder OFF
Mechanical key is inserted to key cylinder ON
KEYLESS LOCK
2LOCK button of key fob is not pressed OFF
LOCK button of key fob is pressed ON
KEYLESS UNLOCK
2UNLOCK button of key fob is not pressed OFF
UNLOCK button of key fob is pressed ON
LIT-SEN FAILLight & rain sensor is in normal condition OK
Light & rain sensor is with internal error NOTOK
OIL PRESS SW Ignition switch OFF or ACC
 Engine runningOFF
Ignition switch ON ON
OUT SIDE TEMP
NOTE:
Diesel engine modelsIgnition switch ONApproximately the same as outside
air temperature
PASSING SWOther than lighting switch PASS OFF
Lighting switch PASS ON
PUSH SW
1Return to ignition switch to LOCK position OFF
Press ignition switch ON
REAR DEF SWRear window defogger switch OFF OFF
Rear window defogger switch ON ON
RKE LOCK AND
UNLOCK
2NOTE:
The item is indicated, but not monitoredOFF
ON
RR FOG SWRear fog lamp switch OFF OFF
Rear fog lamp switch ON ON
RR WASHER SW
3Rear washer switch OFF OFF
Rear washer switch ON ON
RR WIPER INT
3Rear wiper switch OFF OFF
Rear wiper switch INT ON
RR WIPER ON
3 Rear wiper switch OFF OFF
Rear wiper switch ON ON
RR WIPER STOP
3Rear wiper stop position OFF
Other than rear wiper stop position ON
TAIL LAMP SWLighting switch OFF OFF
Lighting switch 1ST ON
TRNK OPNR SWWhen back door opener switch is not pressed OFF
When back door opener switch is pressed ON
TURN SIGNAL LTurn signal switch OFF OFF
Turn signal switch LH ON
TURN SIGNAL RTurn signal switch OFF OFF
Turn signal switch RH ON
UNLOCK WITH DRNOTE:
The item is indicated, but not monitoredOFF
ON
VEHICLE SPEED While driving Equivalent to speedometer reading Monitor Item Condition Value/Status

BCS
BCM (BODY CONTROL MODULE)
BCS-49
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
1: Hatchback
2: Sedan
3: Manual A/C
4: Superlock
5: Remote keyless entry
6: Intelligent Key
7: LHD diesel69
(G)Ground Rear fog lamp OutputLighting switch
1ST and front
fog lamp switch
ONRear fog lamp switch OFF 0V
Rear fog lamp switch ON Battery voltage
70
(B)Ground Ground — — 0V
71
1
(V)Ground Rear wiper motor OutputRear wiper switch OFF 0V
Rear wiper switch ON Battery voltage
72
(LG)GroundBattery power sup-
plyInput — Battery voltage
73
(R)GroundInterior room lamp
power supplyOutputAfter passing the interior room lamp battery
saver operation time0V
Any other time after passing the interior room
lamp battery saver operation timeBattery voltage
74
(Y)GroundBattery power sup-
plyInput — Battery voltage
75
4
(V)Ground Super lock OutputWhen lock button of keyfob or Intelligent Key
is not pressed 0V
When lock button of keyfob or Intelligent Key
is pressed Battery voltage
76
(G)Ground Driver door unlock OutputDoor lock/un-
lock switchPressed to the unlock side Battery voltage
Pressed to the lock side 0V
77
(SB)Ground Door lock (All) OutputDoor lock/un-
lock switchPressed to the unlock side 0V
Pressed to the lock side Battery voltage
78
(L)GroundPower window pow-
er supplyOutput Ignition switchOFF or ACC 0V
ON Battery voltage
79
(Y)GroundBattery power sup-
plyInput — Battery voltage Terminal No.
(Wire color)Description
ConditionReference Value
(Approx.)
Signal nameInput/
Output +−

BCS
BCM (BODY CONTROL MODULE)
BCS-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L B A
O
P N
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Removal and Installation of BCMINFOID:0000000001523223
NOTE:
The LHD model shown, RHD model similar.
REMOVAL
1. Remove the glove box. Refer to IP-11, "Removal and Installation".
2. Remove the BCM screws, disconnect the connectors and
remove the BCM (1).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
 When replacing BCM, it must be configured. Refer to BCS-4, "
CONFIGURATION : Special Repair Require-
ment".
 When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs.
Refer to BCS-3, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
 When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be re-reg-
istered.
WKIA5672E

DLK-11
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P BACK DOOR : Description ....................................
534
BACK DOOR : Component Function Check .......534
BACK DOOR : Diagnosis Procedure ....................534
BACK DOOR : Component Inspection ..................536
TRUNK LID OPENER ACTUATOR .................537
Description ............................................................537
Component Function Check ................................537
Diagnosis Procedure .............................................537
Component Inspection ..........................................538
BUZZER (COMBINATION METER) .................540
Description ............................................................540
Component Function Check ................................540
Diagnosis Procedure .............................................540
HAZARD WARNING LAMPS ...........................541
Description ............................................................541
Component Function Check ................................541
Diagnosis Procedure .............................................541
VEHICLE SPEED SIGNAL CIRCUIT ...............542
Description ............................................................542
Component Function Check ................................542
Diagnosis Procedure .............................................542
KEYFOB BATTERY AND FUNCTION .............543
Description ............................................................543
Component Function Check ................................543
Diagnosis Procedure .............................................543
Component Inspection ..........................................543
Special Repair Requirement .................................543
ECU DIAGNOSIS .......................................544
BCM (BODY CONTROL MODULE) .................544
Reference Value ...................................................544
Wiring Diagram - POWER DOOR LOCK SYSTEM
- .............................................................................
544
Wiring Diagram - REMOTE KEYLESS ENTRY
SYSTEM - .............................................................
552
Wiring Diagram - BACK DOOR OPENER SYS-
TEM - ....................................................................
558
Wiring Diagram - TRUNK LID OPENER SYSTEM
- .............................................................................
562
Fail Safe ...............................................................564
DTC Inspection Priority Chart .............................565
DTC Index ............................................................565
SYMPTOM DIAGNOSIS ............................567
DOOR LOCK FUNCTION SYMPTOMS ...........567
DOOR LOCK AND UNLOCK SWITCH ...................567
DOOR LOCK AND UNLOCK SWITCH : Symptom
Table .....................................................................
567
KEYFOB ..................................................................567
KEYFOB : Symptom Table ...................................567
BACK DOOR OPEN FUNCTION SYMPTOMS
..
569
BACK DOOR OPENER SWITCH ............................569
BACK DOOR OPENER SWITCH : Symptom Ta-
ble ..........................................................................
569
TRUNK OPEN FUNCTION SYMPTOMS ........570
TRUNK LID OPENER SWITCH ...............................570
TRUNK LID OPENER SWITCH : Symptom Table ..570
WARNING FUNCTION SYMPTOMS ..............571
BACK DOOR ...........................................................571
BACK DOOR : Symptom Table .............................571
HAZARD REMINDER FUNCTION ..................572
HAZARD WARNING LAMP .....................................572
HAZARD WARNING LAMP : Symptom Table ......572
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ............................................................
573
Work Flow ..............................................................573
Inspection Procedure .............................................575
Diagnostic Worksheet ............................................577
PRECAUTION ............................................579
PRECAUTIONS ...............................................579
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
579
Procedure without Cowl Top Cover ....................579
Steering Wheel Rotation after Battery Disconn
ect ..........................................................................
579
Work ......................................................................580
PREPARATION .........................................581
PREPARATION ...............................................581
Commercial Service Tool ......................................581
ON-VEHICLE MAINTENANCE ..................582
PRE-INSPECTION FOR DIAGNOSTIC ..........582
Basic Inspection ....................................................582
REMOVAL AND INSTALLATION .............583
HOOD ..............................................................583
Fitting Adjustment ..................................................583
Removal and Installation .......................................584
Removal and Installation of Hood Lock Control ....585
Hood Lock Control Inspection ...............................587
RADIATOR CORE SUPPORT ........................589
Removal and Installation .......................................589
FRONT FENDER .............................................591
Removal and Installation .......................................591
DOOR ..............................................................592
Fitting Adjustment ..................................................592
Removal and Installation .......................................595

DLK-14
REAR LH ..................................................................681
REAR LH : Description ..........................................681
REAR LH : Component Function Check ..............681
REAR LH : Diagnosis Procedure ...........................681
REAR RH .................................................................682
REAR RH : Description .........................................682
REAR RH : Component Function Check .............682
REAR RH : Diagnosis Procedure ..........................683
TRUNK LID OPENER ACTUATOR .................685
Description .............................................................685
Component Function Check ................................685
Diagnosis Procedure .............................................685
Component Inspection ...........................................686
BUZZER (COMBINATION METER) ................688
Description .............................................................688
Component Function Check ................................688
Diagnosis Procedure .............................................688
HAZARD WARNING LAMPS ..........................689
Description .............................................................689
Component Function Check ................................689
Diagnosis Procedure .............................................689
VEHICLE SPEED SIGNAL CIRCUIT ..............690
Description .............................................................690
Component Function Check ................................690
Diagnosis Procedure .............................................690
KEYFOB BATTERY AND FUNCTION ............691
Description .............................................................691
Component Function Check ................................691
Diagnosis Procedure .............................................691
Component Inspection ...........................................691
Special Repair Requirement ..................................691
ECU DIAGNOSIS .......................................692
BCM (BODY CONTROL MODULE) ................692
Reference Value ....................................................692
Wiring Diagram - POWER DOOR LOCK SYSTEM
- .............................................................................
693
Wiring Diagram - REMOTE KEYLESS ENTRY
SYSTEM - ..............................................................
703
Wiring Diagram - BACK DOOR OPENER SYS-
TEM - .....................................................................
709
Wiring Diagram - TRUNK LID OPENER SYSTEM
- .............................................................................
713
Fail Safe ................................................................715
DTC Inspection Priority Chart .............................716
DTC Index .............................................................716
SYMPTOM DIAGNOSIS ............................718
DOOR LOCK FUNCTION SYMPTOMS ..........718
DOOR LOCK AND UNLOCK SWITCH ...................718
DOOR LOCK AND UNLOCK SWITCH : Symptom
Table ......................................................................
718
KEYFOB ..................................................................718
KEYFOB : Symptom Table ...................................719
BACK DOOR OPEN FUNCTION SYMPTOMS
..
720
BACK DOOR OPENER SWITCH ...........................720
BACK DOOR OPENER SWITCH : Symptom Ta-
ble .........................................................................
720
TRUNK OPEN FUNCTION SYMPTOMS .........721
TRUNK LID OPENER SWITCH ..............................721
TRUNK LID OPENER SWITCH : Symptom Table .721
WARNING FUNCTION SYMPTOMS ...............722
BACK DOOR ...........................................................722
BACK DOOR : Symptom Table ............................722
HAZARD REMINDER FUNCTION ...................723
HAZARD WARNING LAMP ....................................723
HAZARD WARNING LAMP : Symptom Table ......723
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ..............................................................
724
Work Flow .............................................................724
Inspection Procedure ............................................726
Diagnostic Worksheet ...........................................728
PRECAUTION ...........................................730
PRECAUTIONS ................................................730
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
730
Procedure without Cowl Top Cover ...................730
Steering Wheel Rotation after Battery Disconn
ect .........................................................................
730
Work ......................................................................731
PREPARATION .........................................732
PREPARATION ................................................732
Commercial Service Tool ......................................732
ON-VEHICLE MAINTENANCE .................733
PRE-INSPECTION FOR DIAGNOSTIC ...........733
Basic Inspection ....................................................733
REMOVAL AND INSTALLATION .............734
HOOD ...............................................................734
Fitting Adjustment .................................................734
Removal and Installation .......................................735
Removal and Installation of Hood Lock Control ....736
Hood Lock Control Inspection ...............................738
RADIATOR CORE SUPPORT .........................740
Removal and Installation .......................................740

DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
DLK-53
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
CONSULT-III Function (INTELLIGENT KEY)INFOID:0000000001396506
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with Intelligent Key unit.
WORK SUPPORT
SELF-DIAG RESULT
Refer to DLK-171, "DTCIndex".
DATA MONITOR
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by Intelligent Key unit.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from Intelligent Key unit.
DATA MONITOR The Intelligent Key unit input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from Intelligent Key unit.
ECU IDENTIFICATION The Intelligent Key unit part number is displayed.
Support item Description Selection item Condition
CONFIRM KEY FOB IDIt can check whether Intelligent Key ID code
is registered or not.——
TAKE OUT FROM WINDOW WARNTake away warning chime (from window)
mode can be changed.ON Active
OFF Inactive
LOW BATT OF KEY FOB WARNIntelligent Key low battery warning mode can
be changed.ON Active
OFF Inactive
KEYLESS FUNCTIONDoor lock function with Intelligent Key can be
changed.ON Active
OFF Inactive
ANSWER BACK FUNCTION Buzzer reminder operation can be changed.ON Active
OFF Inactive
SELECTIVE UNLOCK FUNCTION Anti-hijack mode can be changed.ON Active
OFF Inactive
HAZARD ANSWER BACKHazard reminder operation mode can be
changed.Refer to DLK-45
.
ANSWER BACK WITH I-KEY LOCKBuzzer reminder operation (lock operation)
mode by each door request switch can be
changed. BUZZER Active
OFF Inactive
ANSWER BACK WITH I-KEY UNLOCKBuzzer reminder operation (unlock operation)
mode by each door request switch can be
changed.BUZZER Active
OFF Inactive
AUTO RELOCK TIMERAuto door lock operation mode can be
changed.OFF Inactive
2 min Active
ENGINE START BY I-KEYEngine start function (by Intelligent Key)
mode can be changed. ON Active
OFF Inactive
LOCK/UNLOCK BY I-KEYDoor lock function by door request switch can
be changed. ON Active
OFF Inactive

DLK-198
< SYMPTOM DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION SYMPTOMS
IGNITION KNOB SWITCH DOES NOT TURN ON
IGNITION KNOB SWITCH DOES NOT TURN ON : Symptom TableINFOID:0000000001523328
WARNING LAMP OPERATION MALFUNCTION
NOTE:
 Before performing the diagnosis in the following table, check “Work Flow”. Refer to DLK-16, "
Work Flow".
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
Conditions of Vehicle (Operating Conditions)
 Intelligent Key is registered.
 Key is not inserted in ignition switch.
 One or more registered Intelligent Keys are in the vehicle.
Symptom Table
KEY WARNING LAMP (GREEN) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
 Intelligent Key is registered.
 Key is not inserted in ignition switch.
 One or more registered Intelligent Keys are in the vehicle.
KEY WARNING LAMP (RED) ILLUMINATES
Conditions of Vehicle (Operating Conditions)
Door lock operation warn-
ing chime does not oper-
ate properly.Request switch oper-
ation1. Check Intelligent Key warning buzzer.DLK-1422. Check intermittent incident.XX-XX, "*****"
Intelligent Key button
operation1. Check Intelligent Key warning buzzer.DLK-142
2. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedureReference
page
Symptom Diagnosis/service procedureReference
page
OFF position warning does not operate properly.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident.XX-XX, "*****"
Take away warning does
not operate properly.Any door open to all
doors closed.1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Door is open1. Check LOCK warning lamp. (RED blinking)DLK-1472. Check intermittent incident.XX-XX, "*****"
Take away through
window1. Check LOCK warning lamp. (RED blinking)DLK-147
2. Check intermittent incident. XX-XX, "*****"
Intelligent Key low battery warning does not oper-
ate properly.1.Check “LOW BAT OF KEY FOB WARN” setting in
“WORK SUPPORT”.DLK-532. Check Intelligent Key battery.XX-XX, "*****"
3. Check KEY warning lamp. (GREEN blinking)DLK-146
4. Check intermittent incident.XX-XX, "*****"
Symptom Diagnosis/service procedure Reference page
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (green) illuminates].1. Check steering lock solenoid.DLK-134
2. Replace Intelligent Key unit.SEC-79