schematic NISSAN TIIDA 2009 Service Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2009, Model line: TIIDA, Model: NISSAN TIIDA 2009Pages: 4331, PDF Size: 58.04 MB
Page 4241 of 4331

STC
N
O P
CONTENTS
STEERING CONTROL SYSTEM
EPS
SERVICE INFORMATION .. ..........................
2
PRECAUTIONS .............................................. .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution Necessary fo r Steering Wheel Rota-
tion After Battery Disconnect ............................... ......
2
Service Notice or Precau tion for EPS System ..........3
EPS SYSTEM ... .............................................. .....4
System Description ............................................. ......4
Schematic ........................................................... ......5
CAN Communication ........................................... ......5
TROUBLE DIAGNOSIS ................................. .....6
Fail-Safe Function ............................................... ......6
How to Perform Trouble Diagnosis ..................... ......6
Component Parts Location .................................. ......7
Wiring Diagram - EPS - ... ..........................................8
EPS Control Unit Input/O utput Signal Reference
Value ................................................................... ......
9 EPS Terminal and Reference Value ....................
....10
CONSULT-III Function ( EPS) ..................................11
Symptom Chart .................................................... ....13
TROUBLE DIAGNOSIS FOR SYSTEM ............ 14
DTC C1601 BATTERY VOLT .............................. ....14
DTC C1604 TORQUE SENSOR ......................... ....15
DTC C1606 EPS MOTOR ................................... ....16
DTC C1607 EEPROM ......................................... ....17
DTC C1608 CONTROL UNIT .............................. ....17
DTC C1609 CAN VHCL SPEED ......................... ....18
DTC C1610 CAN ENG RPM ............................... ....19
DTC U1000 CAN COMM CIRCUIT ..................... ....19
Component Inspection ......................................... ....19
TROUBLE DIAGNOSIS FOR SYMPTOMS ...... 21
EPS Warning Lamp Does Not Turn ON ..................21
EPS Warning Lamp Does Not Turn OFF ................21
Steering Wheel Turning Force Is Heavy or Light . ....22
Unbalance Steering Wheel Turning Force and Re-
turn Between Right and Left ................................ ....
23
Unbalance Steering Wheel Turning Force (Torque
Variation) ............................................................. ....
24
Page 4245 of 4331

STC
N
O P
Schematic
INFOID:0000000004307288
COMPONENTS FUNCTION DESCRIPTION
CAN Communication INFOID:0000000004307289
SYSTEM DESCRIPTION CAN (Controller Area Network) is a serial communication li ne for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
For details, refer to LAN-26, " CAN System Specification Chart " .
Page 4293 of 4331

WW
N
O P
CONTENTS
WIPER, WASHER & HORN
SERVICE INFORMATION .. ..........................2
PRECAUTION ................................................ .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution for Procedure without Cowl Top Cover ......2
FRONT WIPER AND WASHER SYSTEM ..... .....3
Component Parts and Harness Connector Loca-
tion ...................................................................... ......
3
System Description ............................................. ......3
CAN Communication System Description ........... ......5
Schematic ........................................................... ......6
Wiring Diagram - WIPER - .................................. ......7
Terminal and Reference Value for BCM ............. ....10
Terminal and Reference Value for IPDM E/R ..... ....10
How to Proceed with Trouble Diagnosis ............. ....10
Preliminary Check ............................................... ....10
CONSULT-III Function (BCM) ............................. ....10
CONSULT-III Function (IPDM E/R) ..................... ....11
Front Wiper Does Not Operate ........................... ....12
Front Wiper Does Not Return to Stop Position (Af-
ter Front Wiper Operate for 10 Seconds, They
Stop for 20 Seconds, and After Repeating the Op-
eration Five Times, They Become Inoperative) .. ....
14
Only Front Wiper Low Does Not Operate ........... ....15
Only Front Wiper High Does Not Operate ........... ....16
Only Front Wiper Intermittent Does Not Operate .... 17
Front Wiper Intermittent Operation Switch Posi-
tion Cannot Be Adjusted ..................................... ....
18
Wiper Does Not Wipe When Front Washer Oper-
ates ..................................................................... ....
18
Front Wiper Does Not Stop ................................. ....18
Removal and Installation of Front Wiper Arms .... ....18
Adjustment of Wiper Arm Stop Location ............. ....19 Removal and Installation of Front Wiper Drive As-
sembly ................................................................. ....
20
Removal and Installation of Front Washer Nozzle ....20
Inspection for Washer No zzle ..................................21
Washer Nozzle Adjustment ................................. ....22
Washer Tube Layout ........................................... ....22
Removal and Installation of Front Wiper and
Washer Switch ..................................................... ....
23
Inspection of Front Wiper and Washer Switch Cir-
cuit ....................................................................... ....
23
Removal and Installation of Washer Tank ...............23
Removal and Installation of Front Washer Motor .... 24
REAR WIPER AND WASHER SYSTEM .......... 25
Component Parts and Harness Connector Loca-
tion ....................................................................... ....
25
System Description .............................................. ....25
Wiring Diagram - WIP/R - .................................... ....27
Terminal and Reference Value for BCM ..................29
How to Proceed with Trou ble Diagnosis ..................29
Preliminary Check ............................................... ....29
CONSULT-III Function (B CM) .................................29
Rear Wiper Does Not Operate ............................ ....29
Rear Wiper Stop Position Is Incorrect ................. ....30
Only Rear Wiper Does Not Operate .................... ....32
Only Rear Wiper Intermittent Does Not Operate . ....32
Wiper Does Not Wipe When Rear Washer Oper-
ates ...................................................................... ....
32
Removal and Installation ..................................... ....32
Washer Nozzle Adjustment ................................. ....35
POWER SOCKET ............................................. 36
Wiring Diagram - P/SCKT - ................................. ....36
Removal and Installation ..................................... ....36
HORN ................................................................ 38
Wiring Diagram - HORN - .................................... ....38
Removal and Installation ..................................... ....38