length NISSAN X-TRAIL 2001 Service Repair Manual

GI-6
PRECAUTIONS
CAUTION:
●Do not use home heating oil, gasoline or other alternate fuels in your diesel engine. The use of
those can cause engine damage.
●Do not use summer fuel at temperatures below –7°C (20°F). The cold temperatures will cause wax
to form in the fuel. As a result, it may prevent the engine from running smoothly.
●Do not add gasoline or other alternate fuels to diesel fuel.
Precautions for Multiport Fuel Injection System or Engine Control SystemEAS000FT
●Before connecting or disconnecting any harness connector for
the multiport fuel injection system or ECM:
Turn ignition switch to “OFF” position.
Disconnect negative battery terminal.
Otherwise, there may be damage to ECM.
●Before disconnecting pressurized fuel line from fuel pump to
injectors, be sure to release fuel pressure.
●Be careful not to jar components such as ECM and mass air
flow sensor.
Precautions for Turbocharger (If Equipped)EAS000FU
The turbocharger turbine revolves at extremely high speeds and
becomes very hot. Therefore, it is essential to maintain a clean sup-
ply of oil flowing through the turbocharger and to follow all required
maintenance instructions and operating procedures.
●Always use the recommended oil. Follow the instructions for
proper time to change the oil and proper oil level.
●Avoid accelerating engine to a high rpm immediately after start-
ing.
●If engine had been operating at high rpm for an extended period
of time, let it idle for a few minutes prior to shutting if off.
Precautions for HosesEAS000FV
HOSE REMOVAL AND INSTALLATION
●To prevent damage to rubber hose, do not pry off rubber hose
with tapered tool or screwdriver.
●To reinstall the rubber hose securely, make sure that hose inser-
tion length and orientation is correct. (If tube is equipped with
hose stopper, insert rubber hose into tube until it butts up
against hose stopper.)
SGI787
SGI292
SMA019D
SMA020D

GI-44
IDENTIFICATION INFORMATION
AUTOMATIC TRANSAXLE NUMBER
MANUAL TRANSAXLE NUMBER
Dimensions EAS000GF
Unit: mm (in)
Wheels & Tires EAS000GG
PAIA0008E
PAIA0009E
PAIA0010E
Overall length 4,510
Overall width 1,765
Overall height 1,675 (Standard), 1,750 (With Rear spoiler)
Front tread 1,530
Rear tread 1,530
Wheelbase 2,625
Conventional Spare
Road wheel/offset mm (in)15 × 6JJ Steel/40 (1.57)
16 × 6.5JJ Steel/Aluminum/40 (1.57)Conventional
Tir e s iz e215/70 R15
215/65 R16Conventional

DRIVE BELTS
EM-13
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
INSTALLATION
1. With box wrench, and while securely holding the hexagonal part in pulley center of drive belt auto-ten-
sioner, move the wrench handle in the direction of arrow (loosening direction of tensioner).
CAUTION:
Avoid placing hand in a location where pinching may occur if the holding tool accidentally comes
off.
2. Insert a rod approximately 6 mm (0.24 in) in diameter into retaining boss to fix auto-tensioner pulley.
3. Hook drive belt onto all pulleys except for water pump. Hook drive belt onto water pump pulley at the end.
CAUTION:
Confirm belts are completely set to pulleys.
4. Release auto-tensioner, and apply tensions to belt.
5. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
6. Confirm tensions of belt at indicator is within the allowable use range. Refer to EM-12, "
Checking Drive
Belts" .
Removal and Installation of Drive Belt Auto-TensionerEBS00KNA
REMOVAL
1. Remove splash cover on RH undercover.
2. Remove drive belt.
●Keep auto-tensioner pulley fixed with a tool such as a short-length screwdriver.
3. Remove drive belt auto-tensioner.
●Remove and install drive belt auto-tensioner by fixing auto-tensioner pulley.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Install drive belt auto-tensioner carefully not to damage the water pump pulley.
SBIA0235E

EM-78
[QR]
CYLINDER BLOCK
CAUTION:
Identify installation positions, and store them without mixing them up.
ASSEMBLY
1. Fully air-blow the engine coolant and engine oil passages in the cylinder block, the cylinder bore and the
crankcase to remove any foreign material.
CAUTION:
Use a goggles to protect your eye.
2. Install each plug to the cylinder block.
●Apply liquid gasket.
Use Genuine Liquid Gasket or equivalent.
●Replace the copper washers with new ones.
3. Install the main bearings and the thrust bearings.
a. Remove dust, dirt, and engine oil on the bearing mating sur-
faces of the cylinder block and the lower cylinder block.
b. Install the thrust bearings to the both sides of the No. 3 journal
housing on the cylinder block.
●Install the thrust bearings with the oil groove facing the crank-
shaft arm (outside).
c. Install the main bearings paying attention to the direction.
●The main bearing with an oil hole and groove goes on the cyl-
inder block. The one without them goes on the lower cylinder
block.
●Only the main bearing (on the cylinder block) for No. 3 journal
has different specifications.
●Before installing the bearings, apply engine oil to the bearing
surface (inside). Do not apply engine oil to the back surface,
but thoroughly clean it.
●When installing, align the bearing stopper to the notch.
●Ensure the oil holes on cylinder block and those on the corre-
sponding bearing are aligned.
4. Install the signal plate to the crankshaft.
a. Position crankshaft and signal plate using a positioning dowel
pin, and tighten mounting bolts.
b. Remove dowel pin.
CAUTION:
Be sure to remove dowel pin.
NOTE:
Dowel pins of crankshaft and signal plate are provided as a set
for each.
If dowel pin is not available (when reusing crankshaft and sig-
nal), use M6-bolt (length below the head of the bolt should be 10
mm or more) as a substitute.
SBIA0276E
PBIC0264E
SBIA0277E
SBIA0278E

CYLINDER BLOCK
EM-91
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
CONNECTING ROD BEND AND TORSION
●Check with connecting rod aligner.
●If it exceeds the limit, replace connecting rod assembly.
CONNECTING ROD BEARING (BIG END)
Install the connecting rod cap without the connecting rod bearing
installed. After tightening the connecting rod bolt to the specified
torque, measure the connecting rod big end inner diameter using an
inside micrometer.
CONNECTING ROD BUSHING OIL CLEARANCE (SMALL END)
Inner Diameter of Connecting Rod (Small End)
Measure inner diameter of bushing.Bend
Limit:
0.15 mm (0.0059 in) per 100 mm (3.94 in) length.
To r s i o n
Limit:
0.30 mm (0.0118 in) per 100 mm (3.94 in) length.
SEM003F
SEM038F
Standard: 48.000 - 48.013 mm (1.8898 - 1.8903 in)
PBIC0119E
Standard: 20.000 - 20.012 mm (0.7874 - 0.7879 in)
PBIC0120E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-99
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
VA LV E
Valve timing
Unit: degree
Valve Dimensions
Unit: mm (in)
Valve Clearance
Unit: mm (in)
*: Reference data at approximately 20°C (68°F) Valve timing
Engine type a b c d e f
QR20DE 212
244 0 64 329
QR25DE 22441
PBIC0187E
Valve head diameter “D”Intake 35.5 - 35.8 (1.398 - 1.409)
Exhaust 30.5 - 30.8 (1.201 - 1.213)
Valve length “L”Intake 97.16 (3.8252)
Exhaust 98.82 (3.8905)
Valve stem diameter “d”Intake 5.965 - 5.980 (0.2348 - 0.2354)
Exhaust 5.955 - 5.970 (0.2344 - 0.2350)
Valve seat angle “α”Intake
45°15′ - 45°45′
Exhaust
Valve margin “T”Intake 1.1 (0.043)
Exhaust 1.3 (0.051)
SEM188A
Item Cold* (reference data) Hot
Intake 0.24 - 0.32 (0.009 - 0.013) 0.32 - 0.40 (0.013 - 0.016)
Exhaust 0.26 - 0.34 (0.010 - 0.013) 0.33 - 0.41 (0.013 - 0.016)

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-101
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
Valve Lifter
Unit: mm (in)
Valve Guide
Unit: mm (in)
Valve Seat
Unit: mm (in) Item Standard
Valve lifter outer diameter 33.965 - 33.980 (1.3372 - 1.3378)
Lifter guide inner diameter 34.000 - 34.021 (1.3386 - 1.3394)
Clearance between lifter and lifter guide 0.020 - 0.056 (0.0008 - 0.0022)
Item Standard part Service part
Valve guide Outer diameter 10.023 - 10.034 (0.3946 - 0.3950) 10.223 - 10.234 (0.4025 - 0.4029)
Inner diameter (Finished size) 6.000 - 6.018 (0.2362 - 0.2369)
Cylinder head valve guide hole diameter 9.975 - 9.996 (0.3927 - 0.3935) 10.175 - 10.196 (0.4006 - 0.4014)
Interference fit of valve guide 0.027 - 0.059 (0.0011 - 0.0023)
Stem to guide clearanceIntake 0.020 - 0.053 (0.0008 - 0.0021)
Exhaust 0.030 - 0.063 (0.0012 - 0.0025)
Projection length “L”Intake 10.1 - 10.3 (0.398 - 0.406)
Exhaust 10.0 - 10.4 (0.394 - 0.409)
PBIC0184E
Item Standard part Service part
Cylinder head seat recess diameter (D)Intake 36.500 - 36.516 (1.4370 - 1.4376) 37.000 - 37.016 (1.4567 - 1.4573)
Exhaust 31.500 - 31.516 (1.2402 - 1.2408) 32.000 - 32.016(1.2598 - 1.2605)
Valve seat interference fitIntake 0.081 - 0.113 (0.0032 - 0.0044)
Exhaust 0.084 - 0.116 (0.0033 - 0.0046)
Valve seat outer diameter (d)Intake 36.597 - 36.613 (1.4408 - 1.4415) 37.097 - 37.113 (1.4605 - 1.4611)
Exhaust 31.600 - 31.616 (1.2441 - 1.2447) 32.100 - 32.116 (1.2638 - 1.2644)
PBIC0284E

EM-136
[YD22DDTi]
OIL PAN AND OIL STRAINER
c. Apply Genuine Liquid Gasket or equivalent, to areas shown in
the figure.
●At the 8 bolt holes marked , liquid gasket should be
applied outside holes.
●Be sure liquid gasket is 3.5 to 4.5 mm (0.138 to 0.177 in)
or 4.5 to 5.5 mm (0.177 to 0.217 in) wide. (Be careful that
the diameter of the silicon bead is different around the
front.)
●Attaching should be done within 5 minutes after coating.
d. Install upper oil pan.
●Tighten bolts in numerical order to specified torque.
●Bolt dimensions vary depending on the installation location.
Refer to the following and use appropriate bolts.
●The shank length under the bolt neck above is the length of
the threaded part (pilot portion not included).
3. Tighten transaxle joint bolts.
4. Install rear plate cover.
5. Install center member.
6. Install crankshaft position sensor (TDC).
7. Install lower oil pan.
a. Use a scraper to remove old liquid gasket from mating surfaces.
●Also remove old liquid gasket from mating surface of
upper oil pan.
JEM118G
M6 x 30 mm (1.18 in) : Bolt No. 15, 16
M8 x 25 mm (0.98 in) : Bolt No. 3, 4, 9, 10
M8 x 60 mm (2.36 in) : Bolt No. 1, 2, 5, 6, 7, 8,
11, 12, 13, 14
SBIA0162E
PBIB0416E
SBIA0163E

EM-150
[YD22DDTi]
FUEL SUPPLY PUMP
19. Using a hexagon-head wrench [face to face 6 mm (0.24 in) SST]
remove bolts to fuel supply pump sprocket.
20. Using the sprocket holder (SST), hold the fuel supply pump
sprocket to prevent falling.
●As for the sprocket holder, install fuel supply pump mounting
bolt through hole of KV11106060 as shown in figure.
●When the sprocket holder is installed, if the positioning stop-
per pin interferes, pull out the stopper pin approximately 10
mm (0.39 in), then install it.
●After the sprocket holder is installed temporarily, insert the
extension bar (SST) and TORX socket in the three holes A.
After positioning the holes, tighten the holder mounting bolts.
●The length of the sprocket holder mounting bolts should be
approximately 15 mm (0.59 in) (M6 thread length).
●Make sure that the a- and b-faces of the sprocket holder con-
tact the bottom side of the sprocket (small diameter side).
CAUTION:
Do not remove the sprocket holder until the fuel supply
pump is installed.
●After the sprocket holder is installed, pull out the positioning
stopper pin (SST) from the fuel supply pump sprocket.
PBIC0945E
SBIA0216E
SBIA0217E
PBIC1254E
SBIA0219E

FUEL SUPPLY PUMP
EM-151
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM
21. Using the extension bar [SST: whole length 43 mm (1.69 in)] and
the TORX socket (Q6-E12: commercially available), remove the
mounting bolts, them remove the fuel supply pump toward the
rear of the engine
CAUTION:
Do not disassemble or adjust the fuel supply pump.
22. Remove the fuel supply pump mounting bolts.
NOTE:
The seal washer of the mounting bolts cannot be reused.
CAUTION:
For removal, be careful not to drop the seal washer into the
engine.
23. Remove adjusting shim.
24. Attach a suitable tool in the M8 bolt hole on coupling.
25. Loosen sprocket nut with the TORX wrench (SST).
26. Remove coupling with a suitable puller.
27. Remove fuel supply pump housing.
●Using a hexagon-head wrench [face to face 5mm (0.20in)
SST], remove bolt to remove fuel supply pump housing.
28. Remove O-rings from fuel supply pump housing.
SBIA0220E
SBIA0221E
PBIC0902E
PBIC0903E
PBIC0904E