torque NISSAN X-TRAIL 2003 Service Repair Manual

WW-26
HORN

Removal and InstallationEKS0033B
REMOVAL
1. Remove the front grille.refer to EI-19, "FRONT GRILLE"
2. Disconnect horn connector.
3. Remove horn.
INSTALLATION
Tighten horn bolt to specified torque.
SKIA0027E
Horn bolt : 17 N·m(1.7 kg-m, 12 ft-lb)

HARNESS
PG-63
C
D
E
F
G
H
I
J
L
MA
B
PG

PGC/V EC EVAP Canister Purge Volume Control Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHONE AV Telephone (Pre-wire)
PNP/SW AT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
PNPSW1 EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS)
POWER PG Power Supply Routing
PRGVLV EC EVAP Canister Purge Volume Control Solenoid Valve
PRWIRE BL Theft Warning System (Pre-wire)
PS/SEN EC Power Steering Pressure Sensor
PST/SW EC Power Steering Oil Pressure Switch
R/FOG LT Rear Fog Lamp
ROOM/L LT Interior Room Lamp
RP/SEN EC Refrigerant Pressure Sensor
RRO2 EC Rear Heated Oxygen Sensor
RRO2/H EC Rear Heated Oxygen Sensor Heater
S/LOCK BL Power Door Lock - Super Lock
S/SIG EC Start Signal
S/WARN SB Seat Belt Warning System
SEAT SE Power Seat
SEN/PW EC Sensor Power Supply
SHIFT AT A/T Shift Lock System
SROOF RF Sunroof
SRS SRS Supplemental Restraint System
SSV/A AT Shift Solenoid Valve A
SSV/B AT Shift Solenoid Valve B
START SC Starting System
STEP/L LT Step Lamp
STOP/L LT Stop Lamp
TAIL/L LT Parking, License and Tail Lamps
TCC/V EC Turbocharger Boost Control Solenoid Valve
TCCSV EC Turbocharger Boost Control Solenoid Valve
TCV AT Torque Converter Clutch Solenoid Valve
TPS AT Throttle Position Sensor
TPS1 EC Throttle Position Sensor (Sensor 1)
TPS2 EC Throttle Position Sensor (Sensor 2)
TPS3 EC Throttle Position Sensor
TURN LT Turn Signal and Hazard Warning Lamp
VIAS EC Variable Induction Air Control System
VSSA/T AT Vehicle Speed Sensor A/T (Revolution Sensor)
VSSMTR AT Vehicle Speed Sensor MTR
WARN DI Warning Lamps
WINDOW GW Power Window Code Section Wiring Diagram Name

HEADLAMP
LT-17
C
D
E
F
G
H
I
J
L
MA
B
LT

CAUTION:

Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.

When replacing bulb, prepare new bulb first of all. Do not leave bulb out of headlamp housing for
a long period, because dust, moisture or smoke will cause performance lowering (fouling, cloud,
etc.) of headlamp reflector and lens.

When bulb is installed, be sure to lock rubber cap to ensure watertightness.
Bulb Replacement for Driving LampEKS00AP9
1. Remove the driving lamp. Refer to LT- 1 8 , "Removal and Installa-
tion for Driving Lamp" in “HEADLAMP”.
2. Disconnect driving lamp connector.
3. Turn bulb socket counterclockwise and unlock it.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

When replacing bulb, prepare new bulb first of all. Do not leave bulb out of driving lamp housing
for a long period, because dust, moisture or smoke will cause performance lowering (fouling,
cloud, etc.) of driving lamp reflector and lens.
Removal and Installation for HeadlampEKS003CI
REMOVAL
1. Remove the front turn signal lamps. Refer toLT- 3 8 , "Removal
and Installation for Front Turn Signal Lamp" .
2. Disconnect connector of headlamp and clearance lamp.
3. Remove the front grille. Refer to EI-19, "
FRONT GRILLE" in
"EXTERIOR & INTERIOR (EI)" section.
4. Remove the headlamp mounting bolts.
5. Pull the headlamp toward the front of the vehicle.
INSTALLATION

Install in the reverse order of removal, taking care of the following points.
Headlamp mounting boltsClearance lamp : 12V 5W
Driving lamp : 12 V - 65 W (H1R1 halogen)
PKIA3396E
PKIA5555E
Headlamp mounting bolts
Tightening torque
: 5.5 N·m (0.55 kg-m, 48 in-lb)

LT-18
HEADLAMP

Removal and Installation for Driving LampEKS00APA
REMOVAL
1. Remove cap (front) and cap (rear).
2. Remove driving lamp mounting nut.
3. Pull the front of driving lamp toward upper side so that undo the
pin from the roof panel.
4. Remove rear end of driving lamp from roof rail.
5. Pull out driving lamp from vehicle and disconnect connector.
INSTALLATION

Install driving lamp in the reverse order of removal, observing the tightening torque shown below.
1. Cap (rear) 2. Driving lamp assembly 3. Nut
4. Cap (front) 5. Driving lamp bracket 6. Grommet
7. Roof rail
PKIA5556E
PKIA3400E
Driving lamp mounting nut
Tightening torque
: 5.7 N·m (0.58 kg-m, 50 in-lb)

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-51
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003C1
PARKING AND TAIL LAMPS
Refer to LT- 6 3 , "Bulb Replacement" .
LICENSE PLATE LAMP
1. Remove license plate lamp mounting screws (2).
2. Remove lens of license plate lamp.
3. Remove bulb from its socket.
4. Installation is the reverse of removal.
Removal and Installation EKS003C2
PARKING AND TAIL LAMPS
Refer to LT- 6 3 , "Removal and Installation" .
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-31, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from license lamp finisher.
Installation

Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.License plate lamp : 12V 5W
PKIA8753E
PKIA5760E
License plate lamp mounting screws
Tightening torque
: 1.4 N·m (0.15 kg-m, 13 in-lb)

FRONT FOG LAMP
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 5 5 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

Do not leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION

Install fog lamp in the reverse order of removal, observing the tightening torque shown below.Front fog lamp :12V 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
Tightening torque
: 5.5 N·m (0.56 kg-m, 49 in-lb)

REAR FOG LAMP
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer to LT- 5 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 1.4 N·m (0.14 kg-m, 12 in-lb)

REAR COMBINATION LAMP
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in "EI EXTERIOR & INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
PKIA8620E
Rear combination lamp mounting bolts
Tightening torque
: 5.4 N·m (0.55 kg-m, 48 in-lb)

IDX-8
ALPHABETICAL INDEX
SROOF - Wiring diagram ................................... RF-11
SRS - See Supplemental Restraint System ..... SRS-6
SRS - Wiring diagram/LHD ............................. SRS-11
SRS - Wiring diagram/RHD ............................ SRS-13
SRS Trouble diagnoses .................................... SRS-8
Stall test (A/T) ...................................... AT-65, AT-257
Standardized relay ............................................. PG-73
START - Wiring diagram ........................ SC-22, SC-23
Start signal ..................................... EC-1199, EC-1496
Starter ................................................................ SC-21
Starting system .................................................. SC-21
Steering gear and linkage inspection ................ MA-43
Steering knuckle ................................................ FAX-7
Steering linkage ................................................. PS-13
Steering wheel and column ..................... PS-7, PS-10
Stop lamp ................................................ LT-42, LT-62
Stop lamp switch ................................ EC-380, EC-733
STOP/L - Wiring diagram ........................ LT-42, LT-62
Suction control valve .... EC-1093, EC-1139, EC-1144,
EC-1382
, EC-1427, EC-1432
Sunload sensor ............. ATC-114, ATC-116, ATC-123
Sunroof .............................................................. RF-10
Super lock .......................................................... BL-42
Supplemental Restraint System ....................... SRS-6
Supplemental restraint system - Wiring diagram/LHD ..
SRS-11
Supplemental restraint system - Wiring diagram/RHD .
SRS-13
Suspension ....................................................... MA-44
Symbols and abbreviations ........................ GI-9, GI-22
Symptom matrix chart .......................... EC-84, EC-532
Synchronizer (M/T) ............................... MT-20, MT-25
System readiness test (SRT) code .................... EC-55
T
Tachometer ........................................................... DI-4
Tail lamp ................................................. LT-47, LT-60
TAIL/L - Wiring diagram .......................... LT-47, LT-88
Tailgate lamp ...................................................... LT-47
TC boost control solnoid valve ........ EC-949, EC-1345,
EC-1471
TC boost sensor ............................................ EC-1038
TCC/V - Wiring diagram ................... EC-951, EC-1472
TCM circuit diagram ........................................... AT-21
TCM inspection table ........................... AT-94, AT-286
THEFT - Wiring diagram .................................. BL-104
Thermal protector ............................................ ATC-95
Thermostat(QR20DEQR25DE) ....................... CO-22
Thermostat(YD22DDTi) .................................... CO-45
Three way catalyst function ............................. EC-261
Three way catalyst precautions ............................ GI-5
Three way catalyst(QR20DEQR25DE) ........... EM-23
Throttle control motor relay ................ EC-302, EC-682
Throttle position sensor (TPS) .......... EC-168, EC-229,
EC-364
, EC-366, EC-401, EC-603, EC-625, EC-716,
EC-718
, EC-755
Throwout bearing - See Clutch release bearing CL-12
Time control system .......................................... BCS-3
Timing chain(QR20DEQR25DE) ..................... EM-44
Timing chain(YD22DDTi) .................. EM-180, EM-185
Torque converter installation ............. AT-415, AT-523
TPS1 - Wiring diagram ..................... EC-231, EC-627
TPS2 - Wiring diagram ..................... EC-170, EC-605
TPS3 - Wiring diagram ..................... EC-403, EC-757
Transmission case (M/T) ...................... MT-19, MT-24
Trouble diagnoses .............................................. GI-10
Turbocharger charge air cooler(YD22DDTi) ... EM-135
Turbocharger precautions ..................................... GI-6
Turbocharger(YD22DDTi) ............................... EM-141
TURN - Wiring diagram .......................... LT-31, LT-33
Turn signal lamp ..................................... LT-31, LT-62
Two trip detection logic ....................... EC-51, EC-513
V
Vacuum hose (brake system) ............................ BR-25
Vacuum hose drawing (Engine control) EC-32, EC-494
Vacuum pump(YD22DDTi) ............................. EM-153
Valve clearance(QR20DEQR25DE) ................ EM-61
Valve clearance(YD22DDTi) ........................... EM-175
Valve guide ....................................................... EM-73
Valve guide(QR20DEQR25DE) ....................... EM-74
Valve lifter(QR20DEQR25DE) ......................... EM-53
Valve lifter(YD22DDTi) ................................... EM-173
Valve seat(QR20DEQR25DE) ......................... EM-75
Valve seat(YD22DDTi) ................................... EM-205
Valve spring(QR20DEQR25DE) ...................... EM-77
Variable induction air control system (VIAS) ... EC-434,
EC-826
Vehicle speed sensor (VSS) EC-272, EC-378, EC-654,
EC-730
Ventilation air filter ........................................ ATC-130
VIAS - Wiring diagram ...................... EC-436, EC-828
W
WARN - Wiring diagram .......................... DI-34
, DI-42
Warning chime .................................................... DI-54
Warning lamps .................................................... DI-33
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-14
Water control valve(QR20DEQR25DE) ........... CO-22
Water pump(QR20DEQR25DE) ...................... CO-20
Water pump(YD22DDTi) ................................... CO-42
Water temperature gauge ..................................... DI-4
Weatherstrip - See Exterior ............................... BL-21
Wheel alignment (front) .................................... FSU-6
Wheel alignment (rear) ..................................... RSU-6
Wheel balance ....................................... WT-4, MA-41
Wheel bearing (rear) ......................................... RAX-6
Wheel hub (front) ............................................... FAX-7
Wheel hub (rear) ............................................... RAX-6
Wheel sensors (ABS) ..................................... BRC-45
WINDOW - Wiring diagram .............................. GW-46
Window, back .................................................. GW-15
Window, back door .......................................... GW-15
Window, door ...................................... GW-80, GW-83