sensor NISSAN X-TRAIL 2003 Service Owner's Guide

EM-150
[YD22DDTi]
OIL PAN AND OIL STRAINER


Tighten bolts in numerical order to the specified torque.

Bolt dimensions vary depending on the installation location.
Refer to the following and use appropriate bolts.

The shank length under the bolt neck above is the length of
the threaded part (pilot portion not included).
3. Tighten transaxle joint bolts.
4. Install rear plate cover.
5. Install center member. Refer to EM-208, "
ENGINE ASSEMBLY" .
6. Install crankshaft position sensor.
7. Install oil pan lower with the following procedure.
a. Use a scraper to remove old liquid gasket from mating surfaces.
CAUTION:

Also remove old liquid gasket from mating surface of oil
pan upper.

Remove old liquid gasket from bolt hole and thread.
b. Apply a continuous bead of liquid gasket with the tube presser
(special service tool: WS39930000) as shown in the figure.
Use Genuine Liquid Gasket or equivalent.

Be sure liquid gasket is 3.5 to 4.5 mm (0.138 to 0.177 in)
wide.

Attaching should be done within 5 minutes after coating.M6 x 30 mm (1.18 in) : Bolt No. 15, 16
M8 x 25 mm (0.98 in) : Bolt No. 3, 4, 9, 10
M8 x 60 mm (2.36 in) : Bolt No. 1, 2, 5, 6, 7, 8,
11, 12, 13, 14
SBIA0162E
PBIC2277E
SBIA0163E
SBIA0164E

VACUUM PUMP
EM-153
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

VACUUM PUMPPFP:41920
Removal and InstallationEBS00LRM
INSPECTION BEFORE REMOVAL
1. Disconnect vacuum hose, and connect a vacuum gauge via 3-way connector.

Disconnect point where vacuum from vacuum pump can be measured directly and install 3-way con-
nector.
2. Start engine and measure generated vacuum at idle speed.

If out of standard, check for air suction in vacuum route, and measure again.

If still outside of standard, replace vacuum pump.
REMOVAL
1. Drain engine coolant. Refer to CO-31, "Changing Engine Coolant" .
2. Remove air duct and air cleaner case. Refer to EM-133, "
Removal and Installation" .
3. Remove charge air cooler. Refer to EM-135, "
Removal and Installation" .
4. Disconnect harness connector from fuel injector.
5. Remove injection tubes. Refer to EM-157, "
Removal and Installation" .
6. Remove rocker cover. Refer to EM-168, "
Removal and Installation" .
7. Remove spill tube. Refer to EM-157, "
Removal and Installation" .
8. Remove nozzle support from No. 2 cylinder and No. 2 fuel injector. Refer to EM-157, "
Removal and Instal-
lation" . (To fix the hexagonal portion of the camshaft.)
9. Remove air inlet pipes. Refer to EM-141, "
Removal and Installation" .
1.Vacuum pump and cylinder head rear cover
assembly2. O-ring 3. Cylinder head rear cover plate
4. Camshaft position sensor
PBIC2315E
Standard:
– 86.6 to – 101.3 kPa (– 866 to – 1,013 mbar, – 650 to – 760 mmHg, – 25.59 to – 29.92 inHg)

EM-154
[YD22DDTi]
VACUUM PUMP

10. Remove exhaust manifold cover. Refer to EM-141, "Removal and Installation" .
11. Disconnect heater hose. Refer to EM-136, "
INTAKE MANIFOLD" .
12. Remove EGR cooler. Refer to EM-136, "
INTAKE MANIFOLD" .
13. Disconnect vacuum hose from vacuum pump side.
14. Remove camshaft position sensor.
15. Remove cylinder head rear cover plate.
16. Loosen and remove the mounting bolts in rear camshaft sprocket. Refer to EM-155, "
Disassembly and
Assembly" .

Loosen rear camshaft sprocket mounting bolt by fixing the hexagonal portion of camshaft.
17. Remove vacuum pump and cylinder head rear cover assembly.

Remove and install vacuum pump, sprocket, drive chain and chain guide as an assembly.

Loosen mounting bolts in reverse order shown in figure.

Do not remove any bolts not shown in figure. (Especially
never remove M6 bolts on vacuum pump.)

U s e t h e s e a l c u t t e r ( s p e c i a l s e r v i c e t o o l : K V 1 0 1111 0 0 ) o r
other suitable tool to remove.
INSTALLATION
1. Install vacuum pump and cylinder head rear cover assembly
onto cylinder head. Refer to EM-156, "
ASSEMBLY" .

Apply a continuous bead of liquid gasket with the tube presser
(special service tool: WS39930000) to area shown in the fig-
ure.
Use Genuine Liquid Gasket or equivalent.

Attaching should be done within 5 minutes after coating.
2. Tighten mounting bolts in order shown in the figure.
3. Install rear camshaft sprocket mounting bolts by fixing the hex-
agonal portion of camshaft.
4. Tighten rear camshaft sprocket mounting bolts.
SBIA0167E
PBIC1141E
SBIA0167E

CYLINDER HEAD
EM-197
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

10. Complete this operation as follows:
a. Turn the ignition switch to “OFF”.
b. Disconnect battery negative terminal.
c. Install glow plug and install all the parts removed in step 4.
d. Install fuel pump fuse [ENG CONT (20A)].
e. Connect battery negative terminal.
f. Using CONSULT-II make sure no DTC is indicated for items of self-diagnosis.
Removal and InstallationEBS00LRW
REMOVAL
1. Drain engine coolant. Refer to CO-31, "Changing Engine Coolant" .
2. Remove the following:

Charge air cooler (Refer to EM-135, "Removal and Installation" .)

Rocker cover (Refer to EM-168, "Removal and Installation" .)

Air cleaner and air duct (Refer to EM-133, "Removal and Installation" .)

Vacuum pump (Refer to EM-153, "Removal and Installation" .)

Spill tube and fuel injector (Refer to EM-157, "Removal and Installation" .)

Intake manifold (Refer to EM-136, "Removal and Installation" .)

Exhaust manifold and Turbocharger (Refer to EM-141, "Removal and Installation" .)

Secondary timing chain (Refer to EM-180, "Removal and Installation" .)

Camshaft (Refer to EM-170, "Removal and Installation" .)
3. Remove cylinder head assembly.
1. Glow plug 2. Cylinder head assembly 3. Cylinder head bolt
4. Copper washer 5. Engine coolant temperature sensor 6. Gasket
7. Water outlet 8. Dowel pin 9. Gasket
10. Glow harness 11. Glow plate 12. Cap
PBIC2437E

CYLINDER HEAD
EM-201
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

4. After installing cylinder head, measure dimension from the front
end surface of cylinder block to that of cylinder head.

If out of the standard, check fitting of dowel pins and cylinder
head.
5. Install glow plug.
CAUTION:

To avoid damage, glow plugs should be removed only when required.

Handle with care to avoid applying shock. When dropped from approx. 10 cm (3.94 in) or higher,
always replace with a new one.

Before installing, remove carbon depositing on mounting hole of glow plug with a reamer.
6. Install engine coolant temperature sensor.
7. Install in the reverse order of removal.
Disassembly and AssemblyEBS00LRX
DISASSEMBLY
1. Remove adjusting shims and valve lifters.

Check the installation positions, and keep them to avoid being confused. Standard : 23.53 - 24.07 mm (0.9264 - 0.9476 in)
JEM172G
1. Adjusting shim 2. Valve lifter 3. Valve collet
4. Valve spring retainer 5. Valve spring 6. Valve oil seal
7. Valve spring seat 8. Valve guide 9. Cylinder head
10. Valve seat 11. Valve (Exhaust) 12. Valve (Intake)
PBIC2328E

ENGINE ASSEMBLY
EM-209
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM

REMOVAL
Description of work
Remove engine, transaxle and transfer assembly with front suspension member from vehicle downward. Sep-
arate suspension member, and then separate engine and transaxle.
Preparation
1. Remove hood assembly. Refer to BL-12, "HOOD" .
2. Drain engine coolant from radiator drain plug. Refer to CO-31, "
DRAINING ENGINE COOLANT" .
3. Remove the following parts.

LH/RH engine undercover

LH/RH front wheels

Battery; Refer to SC-3, "BATTERY" .

Drive belts; Refer to EM-132, "Removal and Installation" .

Air duct and air cleaner case assembly; Refer to EM-133, "Removal and Installation" .

Alternator; Refer to SC-16, "Removal and Installation" .

Radiator and cooling fan assembly; Refer to CO-34, "Removal and Installation" and CO-36, "COOL-
ING FAN" .

Charge air cooler; Refer to EM-135, "CHARGE AIR COOLER" .
4. Disconnect engine room harness from the engine side and set it aside for easier work.
5. Disconnect all the body-side vacuum hoses and air hoses at engine side.
Engine room LH
1. Disconnect fuel feed hose and return hose, and plug it to prevent fuel from draining. Refer to EM-136,
"INTAKE MANIFOLD" .
2. Disconnect heater hose, and install plug it to prevent engine coolant from draining. Refer to EM-136,
"INTAKE MANIFOLD" .
3. Remove clutch operating cylinder from transaxle, and move it aside. Refer to MT-17, "
TRANSAXLE
ASSEMBLY" and CL-10, "OPERATING CYLINDER" .
4. Disconnect shift cable from transaxle. Refer to MT-14, "
CONTROL LINKAGE" .
Engine room RH
1. Remove engine coolant reservoir tank. Refer to CO-34, "RADIATOR" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on body with a rope to
avoid putting load on it. Refer to ATC-144, "
Removal and Installation of Compressor" .
Vehicle underbody
1. Remove exhaust front tube. Refer to EX-2, "Removal and Installation" .
2. Remove propeller shaft. Refer to PR-4, "
Removal and Installation" .
3. Remove steering shaft from steering gear. Refer to PS-10, "
STEERING COLUMN" .
4. Disconnect power steering fluid cooler piping at a point between body and engine. Refer to PS-34,
"HYDRAULIC LINE" .
5. Remove ABS sensor from brake caliper. Refer to BRC-45, "
WHEEL SENSORS" (ABS), BRC-116,
"WHEEL SENSORS" (ESP/TCS/ABS).
6. Remove brake caliper with piping connected from steering knuckle. Temporarily secure it on body with a
rope to avoid load on it. Refer to BR-27, "
FRONT DISC BRAKE" .
7. Remove left and right suspensions from steering knuckle under strut. Refer to FSU-5, "
FRONT SUSPEN-
SION ASSEMBLY" .

EM-246
[YD22DDTi]
SERVICE DATA AND SPECIFICATIONS (SDS)

Spill tube Nozzle side 18.7 (1.9, 14)
Cylinder head side 18.7 (1.9, 14)
Fuel rail57.5 (5.9, 42)
Fuel pump31.4 (3.2, 23)
Fuel pump sprocket39 (4.0, 29)
*1 Camshaft bracket 1) 2 (0.2, 1)
2) 6 (0.6, 4)
3) 12 - 13 (1.2 - 1.4, 9 - 10)
Front chain case
7.9 (0.8, 70)*
2
Chain tensioner
9.6 (0.98, 85)*2
Tension guide23.5 (2.4, 18)
Slack guide23.5 (2.4, 18)
Camshaft sprocket 143 (15, 105)
Oil pump housing12.5 (1.3, 9)
Power steering oil pump 53.5 (5.5, 39)
Rear chain case12.5 (1.3, 9)
Engine coolant temperature sensor 13.5 (1.4, 10)
*1 Cylinder head 1) 35 - 44 (3.5 - 4.5, 26 - 32)
2) 180 degrees to 185 degrees
3) 0 (0, 0)
4) 35 - 44 (3.5 - 4.5, 26 - 32)
5) 90 degrees to 95 degrees (angle
tightening)
6) 90 degrees to 95 degrees (angle
tightening)
Glow plug20.5 (2.1, 15)
*1 Flywheel103 - 112 (10.5 - 11.5, 76 - 83)
Oil pressure switch13 - 17 (1.25 - 1.75, 9 - 12)
Oil jet6.0 - 10.8 (0.62 - 1.1, 54 - 95)
Oil jet relief valve40 - 58 (4.0 - 6.0, 29 - 43)
Rear oil seal retainer12 - 13 (1.2 - 1.4, 9 - 10)

CO-22
[QR]
THERMOSTAT AND WATER CONTROL VALVE

THERMOSTAT AND WATER CONTROL VALVEPFP:21200
Removal and InstallationEBS00KOO
REMOVAL
1. Drain engine coolant. Refer to CO-9, "Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belt.
2. Disconnect radiator hose (lower) at water inlet side. Refer to CO-12, "
RADIATOR" .
3. Remove water inlet and thermostat.
4. Remove water control valve with the following procedure:
a. Disconnect radiator hose (upper) at water control valve housing (water outlet) side.
b. Disconnect harness connector from engine coolant temperature sensor.
c. Remove heater pipe and heater hose.
d. Remove water control valve housing (water outlet) and water control valve.
1. Thermostat 2. O-ring 3. Water inlet
4. Water control valve 5. O-ring 6. Gasket
7. Water control valve housing (water outlet) 8. Washer 9. Engine coolant temperature sensor
10. Heater hose 11. O-ring 12. Heater pipe
13. Heater hose
PBIC2254E

CO-24
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00KOP
CAPACITY
Unit: (lmp qt)
THERMOSTAT
WATER CONTROL VALVE
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
Tightening TorqueEBS00KOQ
Unit: N·m (kg-m, ft-lb)
Unit: N·m (kg-m, in-lb)*
Engine coolant capacity (With reservoir tank at “MAX” level) Approx. 7.1 (6-1/4)
Reservoir tank0.6 (1/2)
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Valve liftMore than 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature More than 77°C (171°F)
Valve opening temperature 93.5 - 96.5°C (200 - 206°F)
Valve lift More than 8 mm/ 108°C (0.315 in/ 226°F)
Valve closing temperature More than 90°C (194°F)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11- 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)
Radiator mounting bracket 4.2 (0.43, 37)*
Radiator cooling fan assembly 4.2 (0.43, 37)*
Cooling fan3.43 (0.35, 30)*
Fan motor4.41 (0.45, 39)*
Water pump24.5 (2.5, 18)
Water pump housing28.0 (2.9, 21)
Water pipe28.0 (2.9, 21)
Water inlet28.0 (2.9, 21)
Water control valve housing (water outlet) 28.0 (2.9, 21)
Hater pipe28.0 (2.9, 21)
Engine coolant temperature sensor 24.5 (2.5, 18)

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC

ENGINE CONTROL SYSTEM
QR (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 19
Alphabetical Index .................................................. 19
DTC No. Index ....................................................... 21
PRECAUTIONS ........................................................ 24
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 24
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 24
Precaution .............................................................. 24
Wiring Diagrams and Trouble Diagnosis ................ 27
PREPARATION ......................................................... 28
Special Service Tools ............................................. 28
Commercial Service Tools ...................................... 29
ENGINE CONTROL SYSTEM .................................. 30
System Diagram ..................................................... 30
Vacuum Hose Drawing ........................................... 32
System Chart ......................................................... 34
Multiport Fuel Injection (MFI) System .................... 34
Electronic Ignition (EI) System ............................... 37
Air Conditioning Cut Control ................................... 37
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 38
CAN Communication Unit ...................................... 38
BASIC SERVICE PROCEDURE .............................. 44
Idle Speed and Ignition Timing Check .................... 44
Accelerator Pedal Released Position Learning ...... 45
Throttle Valve Closed Position Learning ................ 46
Idle Air Volume Learning ........................................ 46
Fuel Pressure Check .............................................. 48
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 51
Introduction ............................................................ 51
Two Trip Detection Logic ........................................ 51
Emission-related Diagnostic Information ................ 52
NATS (Nissan Anti-theft System) ........................... 64
Malfunction Indicator (MI) ....................................... 64
OBD System Operation Chart ................................ 67
TROUBLE DIAGNOSIS ............................................ 73
Trouble Diagnosis Introduction ............................... 73DTC Inspection Priority Chart ................................. 76
Fail-safe Chart ........................................................ 77
Basic Inspection ..................................................... 79
Symptom Matrix Chart ............................................ 84
Engine Control Component Parts Location ............ 88
Circuit Diagram ....................................................... 93
ECM Harness Connector Terminal Layout ............. 95
ECM Terminals and Reference Value ..................... 95
CONSULT-II Function ...........................................102
Generic Scan Tool (GST) Function .......................112
CONSULT-II Reference Value in Data Monitor Mode
.114
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................116
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .119
Description ............................................................119
Testing Condition ..................................................119
Inspection Procedure ............................................119
Diagnostic Procedure ...........................................120
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................123
Description ............................................................123
Diagnostic Procedure ...........................................123
POWER SUPPLY AND GROUND CIRCUIT ...........124
Wiring Diagram .....................................................124
Diagnostic Procedure ...........................................125
Component Inspection ..........................................131
Ground Inspection ................................................131
DTC U1000, U1001 CAN COMMUNICATION LINE .132
Description ............................................................132
On Board Diagnosis Logic ....................................132
DTC Confirmation Procedure ...............................132
Wiring Diagram .....................................................133
Diagnostic Procedure ...........................................134
DTC P0011 IVT CONTROL .....................................135
Description ............................................................135
CONSULT-II Reference Value in Data Monitor Mode
.135
On Board Diagnosis Logic ....................................136