EI-2 NISSAN X-TRAIL 2003 Service Repair Manual

AT-408
[ALL]
ON-VEHICLE SERVICE

Park/Neutral Position (PNP) SwitchECS00CRB
COMPONENTS
REMOVAL AND INSTALLATION
Removal
1. Set select lever in N position.
2. Remove front tire LH from vehicle.
3. Remove LH splash guard. (Front fender side) Refer to EI-21, "
Removal and Installation" .
4. Remove engine under cover.
5. Remove control cable end from manual shaft.
6. Remove PNP switch fixing bolts.
7. Remove PNP switch from transaxle assembly.
Installation
Note the following, and install in the reverse order of removal.

Align PNP switch position when installing.
1. Transaxle assembly 2. PNP switch
SCIA4855E
SCIA3156E
SCIA3154E

AT-412
[ALL]
ON-VEHICLE SERVICE

Revolution Sensor ReplacementECS0040G
COMPONENTS
1. Remove front tire LH from vehicle.
2. Remove LH splash guard.(Front fender side) Refer toEI-21, "
Removal and Installation" .
3. Disconnect revolution sensor harness connector.
4. Remove harness bracket from transaxle assembly.
5. Remove revolution sensor from transaxle assembly.
Installation
Note the following, and install in the reverse order of removal.
CAUTION:

Do not reuse O-ring.

Apply petroleum jelly to O-ring.
1. transaxle assembly 2. Revolution sensor 3. O-ring
SCIA4864E
SCIA2788E

BL-18
DOOR

DOORPFP:80100
Fitting AdjustmentEIS00A67
FRONT DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Working from the inside the fender, loosen hinge mount bolts on the body. Lift rear end of the front door to
adjust clearance and surface difference properly.
REAR DOOR
Longitudinal clearance and surface height adjustment at front end
1. Remove upper and lower garnishes on the center pillar. Refer to EI-35, "BODY SIDE TRIM" .
2. Loosen mounting bolts from outside of vehicle, mounting nuts from inside of vehicle. Open rear door.
Raise rear end of it to adjust.
STRIKER ADJUSTMENT
Adjust striker until it is parallel to the lock engagement direction.
PIIA3652E
PIIA0555E

WINDSHIELD GLASS AND MOLDING
GW-11
C
D
E
F
G
H
J
K
L
MA
B
GW

WINDSHIELD GLASS AND MOLDINGPFP:72700
Removal and InstallationEIS0045I
REMOVAL
1. Remove the front pillar garnish and headlining. Refer to EI-35, "BODY SIDE TRIM" and EI-39, "HEAD-
LINING" .
2. Remove the body side welt on the front pillar.
3. Remove the cowl top cover. Refer to EI-20, "
COWL TOP" .
4. Apply a protective tape around the windshield glass to protect the painted surface from damage.
After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag.

If a windshield glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.
PIIB0581E
PIIA0186E

REAR DOOR GLASS AND REGULATOR
GW-83
C
D
E
F
G
H
J
K
L
MA
B
GW

REAR DOOR GLASS AND REGULATORPFP:82300
Removal and InstallationEIS00468
REMOVAL
1. Remove door outside molding. Refer to EI-22, "Removal and Installation" .
2. Remove rear door finisher. Refer to EI-32, "
Removal and Installation" .
3. Remove sealing screen.
NOTE:
If sealing screen is reused, cut the butyl-tape so that a part of butyl-tape remains on the sealing screen.
4. Operating power window switch, raise or lower the door window
until the carrier plate mounting bolts appear.
5. Remove carrier plate mounting bolts, and place glass on the
door inner.
SIIA0136E
PIIA0554E

EI-2 DOOR FINISHER ...................................................... 32
Removal and Installation ........................................ 32
FRONT AND REAR ............................................. 32
BACK DOOR TRIM ................................................... 34
Removal and Installation ........................................ 34
REMOVAL ........................................................... 34
INSTALLATION .................................................... 34
BODY SIDE TRIM ..................................................... 35
Removal and Installation ........................................ 35
CENTER PILLAR LOWER GARNISH ................. 36
CENTER PILLAR UPPER GARNISH .................. 36
LUGGAGE SIDE LOWER FINISHER ................. 36
REAR PILLAR FINISHER ................................... 36
DASHBOARD SIDE FINISHER ........................... 36
BODY SIDE WELT .............................................. 36FLOOR TRIM ............................................................. 38
Removal and Installation ......................................... 38
REMOVAL ............................................................ 38
INSTALLATION .................................................... 38
HEADLINING ............................................................. 39
Removal and Installation ......................................... 39
REMOVAL ............................................................ 39
INSTALLATION .................................................... 40

EI-20
COWL TOP

COWL TOPPFP:66100
Removal and InstallationEIS000N0
REMOVAL
1. Remove wiper arms (left and right). Refer to WW-8, "Removal
and Installation for Front Wiper Arms, Adjustment for Wiper
Arms Stop Location" .
2. Remove cowl top seal rubber.
3. Remove cowl top rubber mounting clips. Then remove cowl top
cover.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0198E

FENDER PROTECTOR
EI-21
C
D
E
F
G
H
J
K
L
MA
B
EI

FENDER PROTECTORPFP:63840
Removal and InstallationEIS000N1
REMOVAL
1. Remove screws and clips of fender protector.
2. Remove fender protector (front/rear).
INSTALLATION
Installation is in the reverse order of removal.
1. Front fender 2. Clip 3. Fender protector
SIIA0200E

EI-22
DOOR OUTSIDE MOLDING

DOOR OUTSIDE MOLDING PFP:82820
Removal and InstallationEIS0015E
REMOVAL
Front door outside molding
1. Roll the front door window all the way up.
2. Remove front door finisher. Refer to EI-32, "
Removal and Installation" .
3. Remove corner cover and door mirror. Refer to GW-91, "
Removal and Installation" .
4. Disengage front door outside molding pawl.
5. Reaching from inner side of door, use a clip clamp tool to disen-
gage front door outside molding from the pawl.
NOTE:
Insert clip clamp tool into the door tab, then disengage by press-
ing in the direction of arrow. (See figure on the right.)
Rear door outside molding
1. Roll the rear door window all the way up.
2. Remove rear door finisher. Refer to EI-32, "
Removal and Installation" .
3. Remove corner inner cover and corner outer cover. Refer to GW-83, "
Removal and Installation" .
4. Disengage rear door outside mold pawl.
SIIA0201E
SIIA0202E

DOOR OUTSIDE MOLDING
EI-23
C
D
E
F
G
H
J
K
L
MA
B
EI

5. Reaching from inner side of door, use a clip clamp tool to disen-
gage rear door outside molding from the pawl.
NOTE:
Insert clip clamp tool into the door pawl, then disengage by
pressing in the direction of arrow. (See figure on the right.)
INSTALLATION
To install, press molding into the outer panel flange and engage the pawls.
SIIA0202E