EI-2 NISSAN X-TRAIL 2003 Service User Guide

EI-24
SIDE GUARD MOLDING

SIDE GUARD MOLDINGPFP:76840
Removal and InstallationEIS000N3
REMOVAL
Side guard molding (front/rear)
1. Apply masking tape around outer circumference of side guard molding.
2. Remove double-faced adhesive tapes with (wide) resin spatula. Disengage clips and remove side guard
molding.
INSTALLATION
1. Remove double-faced adhesive tape remaining on vehicle.
2. Clean contact surface of vehicle (to side guard molding), and install side guard molding to vehicle.
CAUTION:

Do not let air between contact surfaces when installing.

To secure contact, do not wash vehicle within 24 hours after installation.
1. Side guard molding (front door) 2. Side guard molding (rear door)
SIIA0204E

DOOR OUTSIDE LOWER MOLDING
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI

DOOR OUTSIDE LOWER MOLDINGPFP:82877
Removal and InstallationEIS000N4
REMOVAL
Door outside molding (front/rear)
1. Remove clips of door outside molding.
2. Remove door outside molding (front/rear).
INSTALLATION
Installation is in the reverse order of removal.
1. Door outside lower molding (front door) 2. Door outside lower molding (rear door)
SIIA0206E

EI-26
SIDE SILL PROTECTOR

SIDE SILL PROTECTORPFP:86856
Removal and InstallationEIS000N5
REMOVAL
1. Remove screw and clip of side sill protector.
2. Remove side sill protector.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0207E

ROOF RAIL
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI

ROOF RAILPFP:73820
Removal and Installation (for Hyper Roof Rail)EIS000N6
REMOVAL
1. Remove driving lamp cap (front).
2. Remove driving lamp mounting nuts.
3. Pull driving lamp upward to disconnect clips of driving lamp from roof panel.
4. Disconnect driving lamp harness connector.
5. Remove driving lamp assembly.
6. Remove hyper roof rail caps (front and rear).
7. Remove side rail mounting bolts and nuts, then remove side rail.
8. Remove rear spoiler mounting bolts, then remove rear spoiler.
9. Remove hyper roof rail mounting nuts, then remove hyper roof rail assembly.
10. Remove headlining. Refer to EI-39, "
HEADLINING" .
11. Remove driving lamp bracket, hyper roof rail bracket (front and rear) and roof spoiler bracket.
INSTALLATION
Installation is in the reverse order of removal.
1. Roof rail 2. Rear spoiler 3. Hyper roof rail rear cap
4. Rear spoiler bracket 5. Hyper roof rail center bracket (rear) 6. Hyper roof rail center bracket (front)
7. Hyper roof rail bracket (rear) 8. Hyper roof rail bracket (front) 9. Hyper roof rail front cap
10. Side rail 11. Driving lamp cap (rear) 12. Driving lamp assembly
13. Driving lamp cap (front) 14. Driving lamp bracket
PIIA6946E

EI-28
ROOF RAIL

Removal and Installation (for Roof Rail)EIS008OQ
REMOVAL
1. Remove headlining. Refer to EI-35, "BODY SIDE TRIM" .
2. Remove roof rail mounting nuts and roof rail covers (or roof
spoiler) mounting nuts.
3. Remove roof rail bracket mounting nuts (front and rear).
1. Roof rail 2. Front cap 3. Rear cap
4. Roof rail cover 5. Roof rail bracket (front) 6. Roof rail bracket (rear)
SIIA0265E
SIIA0214E
SIIA0215E

ROOF RAIL
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI

4. Remove roof rail covers (or roof spoiler). For removal of roof spoiler,refer to EI-30, "ROOF SPOILER" .
5. Remove roof rail mounting clips, and remove roof rails.
INSTALLATION
Installation is in the reverse order of removal.

WW-10
FRONT WIPER AND WASHER SYSTEM

REMOVAL
1. Operate the front wiper motor, and stop it at the auto stop posi-
tion.
2. Remove front wiper arm from the vehicle.
3. Remove the cowl top cover. Refer to EI-20, "
COWL TOP" .
4. Remove 4 screws and remove front wiper motor assembly from
the vehicle.
5. Disconnect front wiper motor connector.
6. Remove wiper link from wiper frame.
7. Remove front wiper motor from wiper frame.
INSTALLATION
1. Connect front wiper motor to connector. Turn the wiper switch
ON to operate front wiper motor, then turn the front wiper switch
OFF (auto stop).
2. Disconnect wiper motor connector.
3. Install front wiper motor to the wiper frame.
4. Install front wiper motor assembly to the vehicle.
5. Install wiper link to the wiper motor arm.
6. Connect front wiper motor connector. Turn the front wiper switch
ON to operate the front wiper motor, then turn wiper switch OFF
(auto stop)
7. Rotate motor arm to the upper limit position.
8. Install wiper motor assembly to the vehicle.
9. Turn the wiper switch ON to operate the Wiper motor, then turn
wiper switch OFF (auto stop)
10. Install cowl top cover. Refer to EI-20, "
COWL TOP" .
11. Install wiper arm to the vehicle.
CAUTION:

Do not drop the wiper motor or cause it to contact other
parts.

Check the grease conditions of the motor arm and wiper
link joint (at retainer). Apply grease if necessary.
SKIA0016E
PKIA0475E
SKIA0092E
PKIA0476E

FRONT WIPER AND WASHER SYSTEM
WW-13
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation for Washer Tank EKS0032X
1. Remove washer tank inlet installation screw and pull out washer
tank inlet.
2. Remove fender protector, refer toEI-21, "
FENDER PROTEC-
TOR"
3. Remove washer pump connector.
4. Remove washer tank installation screw and pawl.
5. Remove washer hose, and remove the washer tank from the
vehicle.
CAUTION:
After installation, add water up to the upper level of the washer
tank inlet, and check for water leaks.
Washer tank installation screw
Removal and Installation for Washer Pump EKS0032Y
1. Remove fender protector, refer toEI-21, "FENDER PROTECTOR"
2. Remove washer pump connector and hose.
3. Pull out washer pump in the direction of the arrow in the figure,
and remove the washer pump from the washer tank.
CAUTION:
When installing washer pump, there should be no packing
twists, etc.
PKIA0484E
: 4.5 N-m (0.45 kg-m, 39 in-lb)
PKIA8885E
PKIA0486E

FRONT FOG LAMP
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 5 5 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

Do not leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION

Install fog lamp in the reverse order of removal, observing the tightening torque shown below.Front fog lamp :12V 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
Tightening torque
: 5.5 N·m (0.56 kg-m, 49 in-lb)

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1040, EC-1347
Boring/horning cylinder block(QR20DEQR25DE) .......
EM-103
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-41
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-43
Brake lines and cables inspection ..................... MA-41
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-380, EC-733, EC-1177, EC-1475
BRK/SW - Wiring diagram EC-381, EC-735, EC-1178,
EC-1476
Bulb specifications .............................................. LT-92
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DEQR25DE) .......... EM-55
Camshaft inspection(YD22DDTi) .................... EM-171
Camshaft position sensor (CMPS) EC-1056, EC-1062,
EC-1363
, EC-1369
Camshaft position sensor (PHASE) .. EC-254, EC-646
Camshaft(QR20DEQR25DE) ........................... EM-53
Camshaft(YD22DDTi) ...................................... EM-170
CAN - Wiring diagram ......... EC-133, EC-580, EC-945,
EC-1269
, LAN-10, LAN-26, LAN-51, LAN-69, LAN-87
CAN (Controller Area Network) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
CAN communication EC-38, EC-132, EC-500, EC-579,
EC-888
, EC-944, EC-1268, AT-32, AT-97, AT-329,
TF-43
, BRC-8, LAN-9, LAN-25, LAN-50, LAN-68,
LAN-86
Canister-See EVAP canister ............. EC-476, EC-868
CHARGE - Wiring diagram .................... SC-13, SC-14
Charging system ................................................ SC-12
Chassis and body maintenance ........................ MA-37
CHIME - Wiring diagram ................ DI-52, DI-55, DI-56
CIGAR - Wiring diagram .................................. WW-27
Cigarette lighter ............................................... WW-27
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram .. EC-947, EC-1046, EC-1052,
EC-1271
, EC-1353, EC-1359
Clearance lamp ........................................ LT-4, LT-60
Clock ................................................................... DI-61
CLOCK - Wiring diagram .................................... DI-61
Closed loop control .............................. EC-35, EC-497
Clutch cover ....................................................... CL-14
Clutch disc ......................................................... CL-14
Clutch master cylinder ......................................... CL-8
Clutch operating cylinder ................................... CL-10
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-12
Clutch release mechanism ................................ CL-12
Clutch withdrawal lever ...................................... CL-12
CMPS - Wiring diagram . EC-947, EC-1058, EC-1064,
EC-1271
, EC-1365, EC-1371
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-40
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DEQR25DE) ..... EM-67
Compression pressure(YD22DDTi) ................ EM-196
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DEQR25DE)
EM-101
Connecting rod bearing clearance(YD22DDTi) EM-232
Connecting rod bushing clearance(YD22DDTi) EM-226
Connecting rod(QR20DEQR25DE) ............... EM-101
Connecting rod(YD22DDTi) .............. EM-223, EM-228
CONSULT for engine ......................... EC-102, EC-551
CONSULT-II for engine ................... EC-926, EC-1251
Control lever (M/T) ............................................. MT-14
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-72
Controller Area Network (CAN) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-352, EC-704, EC-1014,
EC-1322
Coolant replacement(QR20DEQR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-28
Cooling circuit (engine)(QR20DEQR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-29
Cooling fan ............................................ CO-18, CO-36
Cooling fan relay EC-363, EC-715, EC-1024, EC-1331
Coupling sleeve (M/T) ........................... MT-20, MT-25
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-888, EC-1219
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-478
, EC-870
Crankshaft position sensor (POS) ..... EC-247, EC-638
Crankshaft position sensor (TDC) EC-1044, EC-1050,
EC-1351
, EC-1357
Crankshaft(QR20DEQR25DE) ........................ EM-83
Cylinder block boring(QR20DEQR25DE) ...... EM-104
Cylinder block boring(YD22DDTi) ................... EM-230
Cylinder block(QR20DEQR25DE) ................... EM-82
Cylinder block(YD22DDTi) .............................. EM-212
Cylinder head bolt tightening(QR20DEQR25DE) ........
EM-69
Cylinder head bolt tightening(YD22DDTi) ....... EM-198
Cylinder head gasket selection(YD22DDTi) ... EM-199
Cylinder head(QR20DEQR25DE) ................... EM-67
Cylinder head(YD22DDTi) .............................. EM-196
D
Data link connector ............................ EC-469
, EC-861
Data link connector for Consult ......... EC-104, EC-553,