em-11 NISSAN X-TRAIL 2003 Service Repair Manual

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
EM-11
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting — Engine NoiseEBS00L7P
PBIC2347E

CAMSHAFT
EM-63
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM


Thickness of new valve lifter can be identified by stamp mark
on the reverse side (inside the cylinder).
Stamp mark “696” indicates 6.96 mm (0.2740 in) in thickness.
NOTE:
Available thickness of valve lifter: 26 sizes range 6.96 to 7.46 mm (0.2740 to 0.2937 in) in steps of 0.02
mm (0.0008 in) (when manufactured at factory). Refer to EM-111, "
Available Valve Lifter" .
5. Install the selected valve lifter.
6. Install camshaft. Refer to EM-58, "
INSTALLATION" .
7. Manually rotate crankshaft pulley a few rotations.
8. Make sure that valve clearances for cold engine are within specifications by referring to the specified val-
ues.
9. After completing the repair, check valve clearances again with the specifications for warmed engine. Make
sure the values are within specifications.
Valve clearance:
Unit: mm (in)
*: Reference data at approximately 20°C (68°F)
KBIA0119E
Hot Cold * (reference data)
Intake 0.32 - 0.40 (0.013 - 0.016) 0.24 - 0.32 (0.009 - 0.013)
Exhaust 0.33 - 0.41 (0.013 - 0.016) 0.26 - 0.34 (0.010 - 0.013)

CYLINDER HEAD
EM-75
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

4. Heat cylinder head to 110 to 130°C (230 to 266°F) by soaking in
heated oil.
5. Press valve guide from camshaft side to dimensions as shown
in the figure.
CAUTION:
Cylinder head contains heat, when working, wear protective
equipment to avoid getting burned.
6. Apply reamer finish to valve guide with a valve guide reamer
(commercial service tool).
VALVE SEAT CONTACT

After confirming that the dimensions of valve guides and valves
are within specifications, perform this procedure.

Apply prussian blue (or white lead) onto contacting surface of
valve seat to check the condition of the valve contact on the sur-
face.

Check if the contact area band is continuous all around the cir-
cumference.

If not, grind to adjust valve fitting and check again. If the contact-
ing surface still has NG conditions even after the re-check,
replace valve seat.
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with oversized [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this. Refer to EM-113, "
Va l v e S e a t" .
SEM008A
Projection “H”:
Intake : 10.1 - 10.3 mm (0.398 - 0.406 in)
Exhaust : 10.0 - 10.4 mm (0.394 - 0.409 in)
PBIC2187E
Standard
Intake and exhaust:
6.000 - 6.018 mm (0.2362 - 0.2369 in)
SEM932C
SBIA0322E

EM-110
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

VA LV E
Valve Timing
Unit: degree
( ): Valve timing control “ON”
Valve Dimensions
Unit: mm (in)
Valve Clearance
Unit: mm (in)
*: Approximately 20°C (68°F) Va l v e t i m i n g
Engine type a b c d e f
QR20DE 212 236 -4 (26) 60 (30)
329
QR25DE 224 244 0 (30) 64 (27) 41
PBIC0187E
Valve head diameter “D”Intake 35.5 - 35.8 (1.398 - 1.409)
Exhaust 30.5 - 30.8 (1.201 - 1.213)
Valve length “L”Intake 97.16 (3.8252)
Exhaust 98.82 (3.8905)
Valve stem diameter “d”Intake 5.965 - 5.980 (0.2348 - 0.2354)
Exhaust 5.955 - 5.970 (0.2344 - 0.2350)
Valve seat angle “α”Intake
45°15′ - 45°45′
Exhaust
Valve margin “T”Intake 1.1 (0.043)
Exhaust 1.3 (0.051)
SEM188A
Items Hot Cold* (reference data)
Intake 0.32 - 0.40 (0.013 - 0.016) 0.24 - 0.32 (0.009 - 0.013)
Exhaust 0.33 - 0.41 (0.013 - 0.016) 0.26 - 0.34 (0.010 - 0.013)

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-111
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

Available Valve Lifter
Valve Spring
Thickness mm (in) Identification mark
6.96 (0.2740) 696
6.98 (0.2748) 698
7.00 (0.2756) 700
7.02 (0.2764) 702
7.04 (0.2772) 704
7.06 (0.2780) 706
7.08 (0.2787) 708
7.10 (0.2795) 710
7.12 (0.2803) 712
7.14 (0.2811) 714
7.16 (0.2819) 716
7.18 (0.2827) 718
7.20 (0.2835) 720
7.22 (0.2843) 722
7.24 (0.2850) 724
7.26 (0.2858) 726
7.28 (0.2866) 728
7.30 (0.2874) 730
7.32 (0.2882) 732
7.34 (0.2890) 734
7.36 (0.2898) 736
7.38 (0.2906) 738
7.40 (0.2913) 740
7.42 (0.2921) 742
744 (0.2929) 744
7.46 (0.2937) 746
KBIA0119E
Free height
mm (in) StandardIntake 44.84 - 45.34 (1.7654 - 1.7850)
Exhaust 45.28 - 45.78 (1.7827 - 1.8024)
Pressure
N (kg, lb) at height mm (in)Standard Intake and exhaust 151 - 175 (15.4 - 17.8, 34 - 39) at 35.30 (1.390)
Squareness mm (in) Limit 1.9 (0.075)

EM-112
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

Valve Lifter
Unit: mm (in)
Valve Guide
Unit: mm (in) Items Standard
Valve lifter outer diameter 33.965 - 33.980 (1.3372 - 1.3378)
Valve lifter hole diameter 34.000 - 34.021 (1.3386 - 1.3394)
Valve lifter clearance 0.020 - 0.056 (0.0008 - 0.0022)
Items Standard part Service part
Valve guideOuter diameter 10.023 - 10.034 (0.3946 - 0.3950) 10.223 - 10.234 (0.4025 - 0.4029)
Inner diameter (Finished size) 6.000 - 6.018 (0.2362 - 0.2369)
Cylinder head valve guide hole diameter 9.975 - 9.996 (0.3927 - 0.3935) 10.175 - 10.196 (0.4006 - 0.4014)
Interference fit of valve guide 0.027 - 0.059 (0.0011 - 0.0023)
Items Standard Limit
Valve guide clearanceIntake 0.020 - 0.053 (0.0008 - 0.0021) 0.08 (0.003)
Exhaust 0.030 - 0.063 (0.0012 - 0.0025) 0.09 (0.004)
Projection length “L”Intake 10.1 - 10.3 (0.398 - 0.406)
Exhaust 10.0 - 10.4 (0.394 - 0.409)
PBIC0184E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-113
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

Valve Seat
Unit: mm (in)
CAMSHAFT AND CAMSHAFT BEARING
Unit: mm (in) Items Standard Oversize [0.5 (0.02)] (Service)
Cylinder head seat recess diameter “D”Intake 36.500 - 36.516 (1.4370 - 1.4376) 37.000 - 37.016 (1.4567 - 1.4573)
Exhaust 31.500 - 31.516 (1.2402 - 1.2408) 32.000 - 32.016(1.2598 - 1.2605)
Valve seat outer diameter “d”Intake 36.597 - 36.613 (1.4408 - 1.4415) 37.097 - 37.113 (1.4605 - 1.4611)
Exhaust 31.600 - 31.616 (1.2441 - 1.2447) 32.100 - 32.116 (1.2638 - 1.2644)
Valve seat interference fitIntake 0.081 - 0.113 (0.0032 - 0.0044)
Exhaust 0.084 - 0.116 (0.0033 - 0.0046)
Items Standard Service
Height “h”Intake 5.9 - 6.0 (0.232 - 0.236) 5.0 - 5.1 (0.197 - 0.201)
Exhaust 5.9 - 6.0 (0.232 - 0.236) 4.91 - 5.01 (0.1933 - 0.1972)
Depth “H”6.0 (0.236)
PBIC2397E
Items Standard Limit
Camshaft runout [TIR*] Less than 0.02 (0.0008) —
Camshaft cam height “A”IntakeQR20DE 45.015 - 45.205 (1.7722 - 1.7797) —
QR25DE 45.665 - 45.855 (1.7978 - 1.8053) —
ExhaustQR20DE 42.825 - 43.015 (1.6860 - 1.6935) —
QR25DE 43.975 - 44.165 (1.7313 - 1.7388) —
Camshaft journal outer diameterNo. 1 27.935 - 27.955 (1.0998 - 1.1006) —
No. 2, 3, 4, 5 23.435 - 23.455 (0.9226 - 0.9234) —
Camshaft bracket inner diameterNo. 1 28.000 - 28.021 (1.1024 - 1.1032) —
No. 2, 3, 4, 5 23.500 - 23.521 (0.9252 - 0.9260) —
Camshaft journal oil clearance 0.045 - 0.086 (0.0018 - 0.0034) —
SEM671

EM-114
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

*: Total indicator reading
CYLINDER BLOCK
Unit: mm (in) Camshaft end play 0.115 - 0.188 (0.0045 - 0.0074) —
Camshaft sprocket runout [TIR*] — 0.15 (0.0059) Items Standard Limit
Surface distortion Limit 0.1 (0.004)
Cylinder bore Inner diameterStandardGrade No. 2 89.010 - 89.020 (3.5043 - 3.5047)
Grade No. 3 89.020 - 89.030 (3.5047 - 3.5051)
Wear limit 0.2 (0.008)
Out-of-round (Difference between “X” and “Y”)
Limit0.015 (0.0006)
Taper (Difference between “A” and “C”) 0.01 (0.0004)
Main bearing housing inner diameter gradeGrade No. A
Grade No. B
Grade No. C
Grade No. D
Grade No. E
Grade No. F
Grade No. G
Grade No. H
Grade No. J
Grade No. K
Grade No. L
Grade No. M
Grade No. N
Grade No. P
Grade No. R
Grade No. S
Grade No. T
Grade No. U
Grade No. V
Grade No. W
Grade No. X
Grade No. Y
Grade No. 4
Grade No. 758.944 - 58.945 (2.3206 - 2.3207)
58.945 - 58.946 (2.3207 - 2.3207)
58.946 - 58.947 (2.3207 - 2.3207)
58.947 - 58.948 (2.3207 - 2.3208)
58.948 - 58.949 (2.3208 - 2.3208)
58.949 - 58.950 (2.3208 - 2.3209)
58.950 - 58.951 (2.3209 - 2.3209)
58.951 - 58.952 (2.3209 - 2.3209)
58.952 - 58.953 (2.3209 - 2.3210)
58.953 - 58.954 (2.3210 - 2.3210)
58.954 - 58.955 (2.3210 - 2.3211)
58.955 - 58.956 (2.3211 - 2.3211)
58.956 - 58.957 (2.3211 - 2.3211)
58.957 - 58.958 (2.3211 - 2.3212)
58.958 - 58.959 (2.3212 - 2.3212)
58.959 - 58.960 (2.3212 - 2.3213)
58.960 - 58.961 (2.3213 - 2.3213)
58.961 - 58.962 (2.3213 - 2.3213)
58.962 - 58.963 (2.3213 - 2.3214)
58.963 - 58.964 (2.3214 - 2.3214)
58.964 - 58.965 (2.3214 - 2.3215)
58.965 - 58.966 (2.3215 - 2.3215)
58.966 - 58.967 (2.3215 - 2.3215)
58.967 - 58.968 (2.3215 - 2.3216)
Difference in inner diameter between cylinders Standard Less than 0.03 (0.0012)
PBIC0281E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-115
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

PISTON, PISTON RING AND PISTON PIN
Available Piston
Unit: mm (in)
Piston Ring
Unit: mm (in)
Piston Pin
Unit: mm (in) Piston skirt diameter “A” StandardGrade No. 2 88.990 - 89.000 (3.5035 - 3.5039)
Grade No. 3 89.000 - 89.010 (3.5039 - 3.5043)
0.20 (0.008) oversize (Service) 89.180 - 89.210 (3.5110 - 3.5122)
Piston height “H” dimension42.0 (1.654)
Piston pin hole diameterGrade No. 0 19.993 - 19.999 (0.7871 - 0.7874)
Grade No. 1 19.999 - 20.005 (0.7874 - 0.7876)
Piston to cylinder bore clearanceStandard 0.010 - 0.030 (0.0004 - 0.0012)
Limit 0.08 (0.0031)
PBIC0188E
Items Standard Limit
Side clearanceTop 0.045 - 0.080 (0.0018 - 0.0031) 0.11 (0.0043)
2nd 0.030 - 0.070 (0.0012 - 0.0028) 0.10 (0.0039)
Oil ring 0.065 - 0.135 (0.0026 - 0.0053) —
End gapTop 0.21- 0.31 (0.0083 - 0.0122) 0.54 (0.0213)
2nd 0.32 - 0.47 (0.0126 - 0.0185) 0.67 (0.0264)
Oil (rail ring) 0.20 - 0.60 (0.0079 - 0.0236) 0.95 (0.0374)
Piston pin outer diameterGrade No. 0 19.989 - 19.995 (0.7870 - 0.7872)
Grade No. 1 19.995 - 20.001 (0.7872 - 0.7874)
Piston to piston pin oil clearance Standard 0.002 - 0.006 (0.0001 - 0.0002)
Connecting rod bushing oil clearance Standard 0.005 - 0.017 (0.0002 - 0.0007)

EM-116
[QR]
SERVICE DATA AND SPECIFICATIONS (SDS)

CONNECTING ROD
Unit: mm (in)
*: After installing in connecting rod
CRANKSHAFT
Unit: mm (in) Center distanceQR20DE 152.85 - 152.95 (6.018 - 6.022)
QR25DE 143.00 - 143.10 (5.630 - 5.634)
Bend [per 100 (3.94)] Limit 0.15 (0.0059)
Torsion [per 100 (3.94)] Limit 0.30 (0.0118)
Connecting rod bushing inner diameter*Grade No. 0 20.000 - 20.006 (0.7874 - 0.7876)
Grade No. 1 20.006 - 20.012 (0.7876 - 0.7879)
Side clearanceStandard 0.20 - 0.35 (0.0079 - 0.0138)
Limit 0.50 (0.0197)
Connecting rod big end diameterGrade No. 0
Grade No. 1
Grade No. 2
Grade No. 3
Grade No. 4
Grade No. 5
Grade No. 6
Grade No. 7
Grade No. 8
Grade No. 9
Grade No. A
Grade No. B
Grade No. C48.000 - 48.001 (1.8898 - 1.8898)
48.001 - 48.002 (1.8898 - 1.8898)
48.002 - 48.003 (1.8898 - 1.8899)
48.003 - 48.004 (1.8899 - 1.8899)
48.004 - 48.005 (1.8899 - 1.8900)
48.005 - 48.006 (1.8900 - 1.8900)
48.006 - 48.007 (1.8900 - 1.8900)
48.007 - 48.008 (1.8900 - 1.8901)
48.008 - 48.009 (1.8901- 1.8901)
48.009 - 48.010 (1.8901- 1.8902)
48.010 - 48.011 (1.8902 - 1.8902)
48.011 - 48.012 (1.8902 - 1.8902)
48.012 - 48.013 (1.8902 - 1.8903)
Center distance “r” QR20DE 40.11 - 40.19 (1.5791 - 1.5823)
QR25DE 49.96 - 50.04 (1.9669 - 1.9701)
Out-of-round (Difference between “X” and “Y”) Limit 0.005 (0.0002)
Taper (Difference between “A” and “B”) Limit 0.005 (0.0002)
Runout [TIR*] LimitQR20DE 0.03 (0.0012)
QR25DE 0.05 (0.0020)
Crankshaft end playStandard 0.10 - 0.26 (0.0039 - 0.0102)
Limit 0.30 (0.0118)
SEM645SBIA0535E