clock reset OLDSMOBILE AURORA 1995 Owners Manual

Elapsed Time (ET) Date
Press DATE to display the date. To change the date,
press DATE then RESET. The following display will
appear:
When the ignition is on, the Driver Information
Center
can be used
as a stopwatch. The display will show hours
and minutes. The elapsed time indicator
will record up
to
100 hours, then it will reset to zero and continue
counting. Press ET, and the display will show the
amount
of time that has elapsed since the elapsed time
indicator was last reset
(not including time the ignition
is off), such
as:
0 1 :OS ELAPSED TIME
To reset elapsed time to zero, press RESET while the
elapsed time
is displayed.
MONTH? XXIDDIYY
MM, DD and YY represent the month, date and year
you currently have in your system. Check to make sure
your clock is
in the correct AM or PM mode.
Notice that each key has a number. Push the key to enter
the number. The first XX’s
will flash until you enter the
first digit for the
month. You don’t need to enter the
leading zero
if the number is under 10. Press ENTER
after you’ve entered the month. The display will change
to:
DAY? MM/XX/Y
Y
Set the day just as you set the month. After the day entry
is made, press ENTER, and the display
will change to:
2-78
ProCarManuals.com

PWWVOL (PowerNolume): With the ignition on,
push this knob to turn the system on or off. Turn it
clockwise to increase the volume. Turn it
counterclockwise to decrease the volume.
AMD": Press this button to change between the AM,
FMI and FM2 bands. The display
will show which band
you are on.
If you press this button while a tape is
playing, the tape
will stop and the radio will return to
the AM or FM band that you were on.
TUNE: Press lightly on this knob to release it from its
recessed position. Turn
it to tune in radio stations. You
may push the knob back
in to return it to its recessed
position when not
in use.
To Preset Radio Stations
The five pushbuttons labeled 1-5 can be used to preset LIP
to 15 radio stations (five AM, five FM 1 and five FM2).
1. Tune in the station you want to store.
2. Press and hold one of the five pushbuttons
until the
display shows
a channel number. The radio will mute
until the cl1annel number is displayed. Whenever you
press that button again, the preset station
will return.
Always check whether you're
in AM, FMl or FM2.
SEEK A/V: When you press SEEK while playing the
radio, the radio
will search for the next higher or lower
station and stop. The radio will be muted while seeking.
SCAN: When you press SCAN while playing the radio,
the radio
will go through each station, pausing for a few
seconds at each station. Press SCAN again to stop
on a
station. The radio
will be muted while scanning and
"SCAN"
will appear on the display.
When you press SCAN and hold
it for about two
seconds
until the display shows "PSCAN" (Preset Scan),
the radio
will scan only stations that you've preset with
your radio pushbuttons. Press SCAN again to stop on a
station.
RECALL: When the ignition is off, press RECALL to
display the time. When the radio
is on, press RECALL
to switch the display between the radio station and the
time. After five seconds the display
will return to its
normal display.
The radio can be set
so that either the time or radio
station is normally displayed when the radio is playing.
To
do this. press RECALL to display the time or radio
station
as desired, then hold RECALL down untii the
display flashes.
ProCarManuals.com

AR/VFM Stereo Radio with Automatic Tone
Control and Cassette Tape Player PWRNOL (PowerNolume): With the ignition on,
push this knob to turn the system on
or off. Turn it
clockwise to increase the volume. Turn
it
counterclockwise to decrease the volume.
AMEM: Press this button to change between the AM,
FMl and FM2 bands. The display will show which band
you are on.
If you press this button while a tape is
playing, the tape will stop and
the radio will return to
the
AM or FM band that you were on.
TUNE: Press lightly on this knob to release it from its
recessed position. Turn it to tune in radio stations. You
may push
the knob back in to return it to its recessed
position when
not in use.
To Preset Radio Stations
The five pushbuttons labeled 1-5 can be used to preset up
to
15 radio stations (five AM, five FM1 and five FM2).
1. Tune in the station you want to store.
2. Press TONE to select the setting that you prefer.
This audio
system may have an optional trunk-mounted
CD changer.
If so, also see “Trunk-Mounted CD
Changer” later in this section.
The digital display indicates information on time or radio
3. Press and hold one of the five pushbuttons until the
station frequency, the AM or FM radio band, whether the
display shows a channel number. The radio will mute
station is
in stereo, and other audio system functions. until the channel number is displayed. Whenever you
press that button again, the preset station and tone
setting will return. Always check whether you’re
in
AM, FMl or FM2.
3-18
ProCarManuals.com