headlamp OLDSMOBILE AURORA 1996 Owners Manual

Operation
The driver’s door will unlock when UNLOCK is pressed.
If pressed again within
25 seconds, all doors will unlock.
Pressing the UNLOCK button will also illuminate the interior lamps. (See “Illuminated Entry”
in the Index.)
All doors will lock when
LOCK is pressed.
The trunk will unlock when the opened trunk symbol is
pressed, but only when the ignition is off. The trunk
symbol will also work when the ignition is on, but only
while in PARK
(P) or NEUTRAL (N).
Panic Mode
When the button with the horn symbol on the key
transmitter is pressed, the horn will sound and the
headlamps and taillamps will flash for up to two
minutes. This can be turned off by pressing the panic
button again, unlocking the vehicle with a key or by
turning the ignition to
on.
If only the panic button works, the transmitter needs to
be resynchronized to the receiver. Do this by pressing
and holding both the
LOCK and UNLOCK buttons for
about eight seconds; you must be within range of the
vehicle. Once the transmitter has been resynchronized,
the horn will chirp and the exterior lamps will flash
once. The system should now operate properly.
Personalization Features
Each key transmitter can be programmed to the driver’s
preference for programmable automatic door locks, key
transmitter response and perimeter lighting. See each
feature in the Index.
The transmitters can also be programmed to move the
driver’s seat and outside mirrors to a set memory position
when the key transmitter’s
UNLOCK button is pressed.
To program the system:
1.
2.
3.
4.
Adjust the driver’s seat to a comfortable position.
Adjust both outside mirrors to suit you. See “Outside
Mirrors” in the Index.
Press the SET button on the driver’s door armrest.
You will hear one beep.
Within five seconds, press one of the two memory
buttons on the armrest. You will hear two beeps
to
confirm that the mirror and the seat positions are
entered into memory.
Press the UNLOCK button on the appropriate
transmitter within five seconds. You will hear
two beeps.
The second key transmitter can be programmed to
record a different seat and mirror position by following
the same steps.
2-9
. -~ ..
ProCarManuals.com

Tilt Wheel hrn Signal/Multifunction Lever
A tilt steering wheel allows you to adjust the steering
wheel before
you drive.
You can also raise it to the highest level to give your
legs more room when you exit and enter the vehicle.
To tilt the wheel, hold the steering wheel and pull the
lever toward
you. Move the steering wheel to a
comfortable level, then release the lever
to lock the
wheel in place. The
lever on the left side
of the steering column
includes your:
0 Turn Signal and Lane Change Indicator
0 Cruise Control
0 Headlamp High/Low Beam
0 Parking Lamps
0 Flash-To-Pass Feature
ProCarManuals.com

lhrn Signal On Chime
If your turn signal is left on for more than 3/4 of a mile
(1.2 km), a chime will sound at each flash of the turn
signal. To turn off the chime, move the turn signal lever
to the off position.
Headlamps
0 Parking Lamps
Sidemarker Lamps
Taillamps
0 Instrument Panel Lights
0 License Plate Lamps
#, Turn the band to this symbol to turn on:
Headlamps
0 Parking Lamps
-‘a-
0 Sidemarker Lamps
0 Taillamps
0 Instrument Panel Lights
m License Plate Lamps
Turn the band to
OFF to turn off the lampshights.
2-35
ProCarManuals.com

Flash-To-Pass
I
If the headlamp switch is left on you’ll hear a warning
chime when you turn the ignition
off, remove the key
from the ignition and open the driver’s door.
Headlamp High/Low Beam
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high beams are on, a light on the instrument
panel also will be on.
This feature lets you use your high-beariheadlamps to
signal .a driver
in front of you that you want to pass. It
works even if your headlamps are
off.
To use it, pull the turn signal lever toward you.
If your headlamps are
off, your high-beam headlamps
will turn on. They’ll stay on as long as you hold the
lever there. Release the lever to turn them
off.
If your headlamps are on, but on low beam, the system
works normally. Just pull the lever until it clicks. Your
headlamps will shift to high beam and stay there.
To
return to low beam, just pull the lever toward you.
If your headlamps are on, and on high beam, your
headlamps will switch to low beam.
To get back to high
beam, pull the lever toward you.
2-36
ProCarManuals.com

Windshield Washer
The lever on the right side of your steering column also
controls your windshield washer. To spray washer fluid
on the windshield, pull the lever toward you. The wipers
will clear the window and then either stop or return to
your preset speed. For more washer cycles, pull and
hold the lever.
If the fluid level in the windshield washer bottle is low,
the message LOW WASHER
FLUID will appear in the
Driver Information Center. See “Windshield Washer
Fluid”
in the Index.
Driving without washer fluid can be dangerous. A bad
mud splash can block your vision.
You could hit another
vehicle or go
off the road. Check your washer fluid
level often.
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can
form ice on the windshield, blocking
your vision.
Lamps
Headlamps
See “Turn Signal/Multifunction Lever” in the Index.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top
of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
The DRL system will make your low-beam headlamps
come on at reduced brightness in daylight when:
The ignition is on,
The headlamp switch is off, and
0 The transaxle is not in PARK (P).
ProCarManuals.com

When DRL are on, only your low-beam headlamps will
be on. The parking lamps, taillamps, sidemarker and
other lamps won’t be
on. Your instrument panel won’t
be lit up either.
When it’s dark enough outside, your low-beam
headlamps will change to full brightness. The other
lamps that come on with your headlamps will also come
on. When it’s bright enough outside, the regular lamps
will go
off, and your low-beam headlamps change to the
reduced brightness of DRL.
To idle your vehicle with thk DRL off, shift the
transaxle into PARK (P). The DRL will stay off until
you shift out of PARK (P).
To turn off all exterior lighting at night when you are
parked, turn off the headlamps and move the twilight
sentinel control all the way toward
MIN.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps
To turn on the fog lamps,
first turn on the parking
lamps or headlamps. Then
press the fog lamp switch. A
light will glow
on the
switch when the switch is
on. To turn off the fog
lamps, press it again.
The fog lamps will also switch off when you turn on
your high-beam headlamps, but will turn on again when
you switch to low beams.
ProCarManuals.com

Cornering Lamps Twilight Sentinel
TWILIGHTSENTINEL
Twilight sentinel turns your
headlamps, taillamps and
parking lamps on and off by
sensing how dark it is
outside.
The cornering lamps are designed to
come on when you
signal a turn. This will provide more light for cornering
at night. To
operate it, leave the headlamp switch off and move
the twilight sentinel control toward MAX.
If you move the control all the way to MAX, your lamps
will remain on for three minutes after you turn off your
engine.
If you move the control toward MIN, the lamps
will
go off quickly when you turn off your engine. You
can set this delay time for only
a few seconds or up to
three minutes.
Light Sensor
Your twilight sentinel and daytime running lamps work
with the light sensor on top
of the instrument panel.
Don’t cover
it up. If you do it will read “dark” and the
headlamps will come on.
- ~~ ~~
~~
ProCarManuals.com

Interior Lamps
Instrument Panel Brightness
1
You can brighten or dim your instrument cluster,
radio and climate control displays and control lights
by rotating the INTERIOR LIGHTS control between
LO and HI when your lights are on. Rotate the control
all the way to HI and you,will turn on the interior
courtesy lamps.
Time Out Feature
The interior lamps will automatically shut off after
10 minutes if a door is left open. This feature is
designed to help eliminate battery wear down.
Courtesy Lamps
When any door is opened, several lamps go on. They
make it easy for you to enter and leave the car.
To turn
on these lamps, rotate the INTERIOR .LIGHTS knob all
the way to HI.
Delayed Illumination
When you open the door, the interior lamps will come
on. When you close the door with
the ignition off, the
interior lamps will stay
on for 25 seconds or until the
ignition is turned to the on position. Please note that
locking the doors will override the delayed illumination
feature and the lights will turn
off right away.
Theater Dimming
This feature allows for a three to five-second fade out of
the courtesy lamps instead of immediate
turn off.
Parade Dimming
This feature prohibits the dimming of your instrument
panel displays during daylight while your headlamps are
on. This feature operates with the light sensor for the
twilight sentinel and is
fully automatic. When the light
sensor reads darkness outside, you will be able to dim
your instrument panel displays once again.
t
ProCarManuals.com

Exit Lighting
With this feature, the interior lamps will come on for
25 seconds after you remove the key from the ignition.
This will give
you time to find the door pull handle or
lock switches.
Illuminated Entry
Press the UNLOCK button on the key transmitter and
the interior courtesy lamps will come on and stay on for
up to a minute. The lamps will turn off immediately by
pressing the
LOCK button on the key transmitter,
starting the ignition or activating the power door locks.
Perimeter Lighting
When the UNLOCK button on the key transmitter is
pressed, the headlamps, parking lamps, back-up lamps
and cornering lamps will come on
if it is dark enough
outside according to the twilight sentinel.
This option can be programmed on or
off for each
transmitter.
To turn the feature offi
1. Press and hold the door lock switch throughout this
procedure. All doors will lock.
2. Press the panic button on the transmitter. Perimeter
lighting remains on at this time and the horn will
chirp two times.
3. Press the panic button on the key transmitter again.
Perimeter lighting is disabled and the horn will chirp
one time.
4. Release the door lock switch. The perimeter lighting
To turn the feature on:
option is now off.
1.
2.
3.
4.
Press and hold the door
lock switch throughout this
procedure. All doors will lock.
Press the panic button on the key transmitter.
Perimeter lighting remains off at this time and the
horn will chirp one time.
Press the panic button on the transmitter again.
Perimeter lighting is now enabled and the horn will
chirp two times.
Release the door
lock switch. The perimeter lighting
option is now on.
ProCarManuals.com

v11 '--ors
Electulchromic Day, A. ght Rearvir .~rror w
Your vehicle may have an automatic electrochromic
day/night rearview mirror.
This mirror automatically changes
to reduce glare from
headlamps behind you. A photocell on the back of the
mirror senses when it is becoming dark outside. Another
photocell built into the mirror surface, senses when
headlamps are behind you. At
night, when the glare is too high, the mirror will
gradually darken to reduce glare (this change may take a
few seconds). The mirror will return
to its clear daytime
state when the glare is reduced.
Press the button at the base of the mirror to turn on the
automatic feature. The button has an indicator light to
show it is on. Press the button again
to turn the
automatic feature off.
Dt -
The automatic mirror has a time delay feature which
prevents unnecessary switching from the night back to
the day position. This delay prevents rapid changing of
the mirror as you drive under lights and through traffic.
u= Day 1c
The reverse day mode is another important feature
of the electrochromic mirror. When you shift into
REVERSE (R), the mirror changes to the day mode.
This gives you a bright image in the mirror as you
back up.
Use a cotton swab and glass cleaner to clean the
photocells when necessary.
ProCarManuals.com