change time OLDSMOBILE AURORA 2002 Owners Manual

ii
GENERAL MOTORS, GM, the GM Emblem,
OLDSMOBILE, the OLDSMOBILE Rocket Emblem
and the AURORA Emblem are registered trademarks of
General Motors Corporation. ªAURORAº is used with
the permission of Hankook Tire.
This manual includes the latest information at the time
it was printed. We reserve the right to make changes
after that time without further notice. For vehicles first
sold in Canada, substitute the name ªGeneral Motors
of Canada Limitedº for Oldsmobile Division whenever
it appears in this manual.
Please keep this manual in your vehicle, so it will
be there if you ever need it when you're on the road.
If you sell the vehicle, please leave this manual in it
so the new owner can use it.
We support voluntary
technician certification.
For Canadian Owners Who Prefer a
French Language Manual:
Aux propri‡taires canadiens: Vous pouvez vous
procurer un exemplaire de ce guide en fran†ais chez
votre concessionaire ou au:
Helm, Incorporated
P.O. Box 07130
Detroit, MI 48207
ProCarManuals.com

1-35
4. Buckle, position and release the safety belt as
described in ªRear Seat Passenger Positionsº
earlier in this section. Make sure that the shoulder
belt crosses the shoulder.
To remove and store the comfort guides, squeeze the
belt edges together so that you can take them out of the
guides. Slide the guide into its storage pocket on the side
of the seatback.
Children
Everyone in a vehicle needs protection! This includes
infants and all other children. Neither the distance
traveled nor the age and size of the traveler changes
the need, for everyone, to use safety restraints. In fact,
the law in every state in the United States and in every
Canadian province says children up to some age must be
restrained while in a vehicle.
Infants and Young Children
Every time infants and young children ride in vehicles,
they should have the protection provided by the
appropriate restraint. Young children should not use
the vehicle's safety belts, unless there is no other choice.
ProCarManuals.com

2-10 Leaving Your Vehicle
When you leave the vehicle, open your door and set the
locks from the inside, then get out and close the door.
Remote Keyless Entry System
With this feature, you can lock and unlock your doors or
unlock your trunk from about 3 feet (1 m) up to 30 feet
(9 m) away using the remote keyless entry transmitter
supplied with your vehicle.
Your remote keyless entry system operates on a
radio frequency subject to Federal Communications
Commission (FCC) Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.Changes or modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
At times you may notice a decrease in range. This is
normal for any remote keyless entry system. If the
transmitter does not work or if you have to stand closer
to your vehicle for the transmitter to work, try this:

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

Check the location. Other vehicles or objects may
be blocking the signal. Take a few steps to the left or
right, hold the transmitter higher, and try again.

Check to determine if battery replacement is
necessary. See the instructions that follow.

If you're still having trouble, see your dealer or
a qualified technician for service.
ProCarManuals.com

2-13 Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
See your dealer to match transmitters to another vehicle.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about four years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.
NOTICE:
When replacing the battery, use care not to
touch any of the circuitry. Static from your
body transferred to these surfaces may damage
the transmitter.
ProCarManuals.com

2-84
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET, STARTING DISABLED and the HOT...STOP
ENGINE warning), press the RESET button.
Pressing the SELECT right arrow button will allow you
to access the following modes, DATE/ET, FUEL,
ECON, OIL and GAGE. While in any of these modes,
warning messages can interrupt and take over the
display until you acknowledge the message, or the
condition causing the problem goes away.
English/Metric
The DIC can display information in either English or
metric. To change the display, press and hold the
ON/OFF button for about three seconds. This will also
change the digital screen for the climate control system
between English and metric.
Date/Elapsed Time
Pressing the SELECT down arrow while in DATE/ET
mode will allow you to choose between the date and the
elapsed time menus.Date
To set the date, press and hold the RESET button for
about three seconds while the date is being displayed on
the DIC. When the date set mode is entered the display
will show the following:
YEAR?_____ MM/DD/00
The year will be flashing. To increase the item that is
flashing press SELECT right arrow. To decrease the
item that is flashing press SELECT down arrow.
When you reach the current year press the RESET
button. The DIC will ask for the month. The month will
flash the same as the year. Use the SELECT buttons to
reach the current month and press RESET. The DIC will
then ask for the day. The day will flash the same as the
year. Use the SELECT buttons to reach the current day.
Press the RESET button again and the set display will
stop flashing and go back to the normal operation mode.
ProCarManuals.com

2-85
Elapsed Time (ET)
When the ignition is on, the DIC can be used as a
stopwatch. The display will show hours and minutes.
The elapsed time indicator will record up to 100 hours,
then it will reset to zero and continue counting. Press
SELECT down arrow while in the DATE/ET mode, and
the display will show the amount of time that has
elapsed since the elapsed time indicator was last reset
(not including time the ignition is off), such as:
01:08 ELAPSED TIME
To start or stop the counting of time, press the RESET
button briefly. If the colon (:) in the time is flashing,
time is being counted. Time is displayed in hours and
minutes. Seconds are not displayed. Time will continue
to be counted as long as the ignition is on, even if
another display is being shown on the DIC.
To reset elapsed time to zero, press the RESET button
for three seconds while the elapsed time is displayed.
Fuel
Press the SELECT down arrow while in the FUEL
mode to see how much fuel has been used and the
fuel range functions.Fuel Used
While in the FUEL USED function the display will
show a reading such as:
FUEL USED: 10.4 GAL or FUEL USED: 39.4 L
To learn how much fuel will be used from a specific
starting point, first enter the FUEL USED mode to
display FUEL USED, then press and hold the RESET
button for three seconds.
Don't confuse fuel used with the amount of fuel in
your tank.
Fuel Range
The FUEL RANGE mode calculates the remaining
distance you can drive without refueling. It's based on
fuel economy and the fuel remaining in the tank. The
display will show a reading such as:
FUEL RANGE: 235 MI or FUEL RANGE: 378 KM
If the range is less than 50 miles (80 km), the display
will read LOW FUEL RANGE.
The fuel economy data used to determine fuel range is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated. Fuel
range cannot be reset.
ProCarManuals.com

2-86 Fuel Economy
Pressing the SELECT down arrow while in the
ECON mode displays average fuel economy and
instantaneous fuel economy calculated for your
specific driving conditions.
Average fuel economy will be shown in a reading
such as:
25.2 AVG MI/GAL or 9.3 AVG L/100 KM
Instantaneous fuel economy will be shown in a reading
such as:
28 INST MI/GAL or 8.4 INST L/100 KM
The average fuel economy is viewed as a long
-term
approximation of your overall driving conditions.
If you press and hold RESET for three seconds in this
mode while you're driving, the system will begin
figuring average fuel economy from that point in time.
Instantaneous fuel economy cannot be reset.
Oil Life
The GM Oil Life System
is the only function
accessible in the OIL mode. Engine oil life is displayed
in a reading such as the following:
OIL LIFE 30%
This is an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an oil
change. It will alert you to change your oil on a schedule
consistent with your driving conditions.
When the remaining oil life is low, the system will alert
you with this message:
CHANGE OIL SOON
Always reset the OIL LIFE reminder after an oil change.
To reset the oil life system, see ªOil Life Systemº in
the Index. Also, see ªEngine Oil, When to Changeº in
the Index.
Remember, you must reset the OIL LIFE yourself after
each oil change. It will not reset itself. Also, be careful
not to reset the OIL LIFE accidentally at any time other
than when the oil has just been changed. It can't be reset
accurately until the next oil change.
ProCarManuals.com

2-87
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule in
this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. If you drive in dusty areas, change your oil
after every 3,000 miles (5 000 km) or three months,
whichever occurs first, unless the DIC instructs you to
do so sooner. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.
Gage
Pressing the SELECT down arrow while in GAGE
mode will allow you to access the battery volts, oil
pressure and tire pressure displays. Pressing and holding
the RESET button for three seconds while in average
speed and tire pressure displays will reset them. Pressing
the SELECT down arrow in GAGE mode will show the
following displays:

Battery voltage, such as the following:
VOLTS: 13.8

Oil pressure, such as the following:
OIL PRESSURE 40 PSI or OIL
PRESSURE 276 KPA
Average speed, such as the following:
AVG SPEED 55 MPH or AVG SPEED 90 KM/H

Tire pressure status, such as the following:
TIRE PRESSURE NORMAL or TIRE
PRESSURE LOW
TIRE PRESSURE NORMAL appears when the
check tire pressure system believes your vehicle's
tire pressures are normal. If a potential tire pressure
problem is detected, the display will show TIRE
PRESSURE LOW. If you see this message, you
should stop as soon as you can and check all four
tires for damage. If a tire is flat, see ªIf a Tire Goes
Flat º in the Index. Also check the tire pressure in all
four tires as soon as you can. See ªTire Pressureº in
the Index.
There are times when you will have to reset
(calibrate) the check tire pressure system. Pressing
the RESET button while the TIRE PRESSURE
LOW warning is displayed does not automatically
reset the tire pressure monitoring system. See
ªCheck Tire Pressure Systemº in the Index for
more information.
ProCarManuals.com

2-89
The DIC is used to program the personal choices of
two drivers. The drivers are recognized as DRIVER 1
and DRIVER 2. You will let the DIC and the vehicle
know which driver you are by using your remote keyless
entry transmitter or by pressing the appropriate memory
seat button located on the driver's door or choosing
the driver with the DIC. Each remote keyless entry
transmitter was pre
-programmed to belong to
DRIVER 1 or DRIVER 2. The personalization
features may be programmed differently for each driver.
When you press the unlock symbol on the transmitter,
the DIC will automatically change driver numbers
and the vehicle will recall the personal choice settings
that were last made to correspond to your transmitter,
including your radio and comfort control settings.
See ªComfort Controls, Personalizationº in the Index.
If you unlock the vehicle using the door key instead
of the transmitter, the personal choice settings will
correspond to the previous driver of the vehicle as
identified by the transmitter, the memory seat control
or the DIC. If this happens and you were not the last
driver of the vehicle, press the correct driver number
on the door panel for the memory seats, press the
unlock symbol on the transmitter or select the
personalization programming mode and choose
the correct driver number.After you have the correct driver number on the display
use the SELECT down arrow button to scroll through
the following messages and feature options:

DOORS LOCK IN GEAR
-- YES/NO

DOORS UNLOCK
-- YES/NO

ALL DOORS IN PARK
-- YES/NO

ALL DOORS AT KEY OFF
-- YES/NO

DRIVERS DOOR IN PARK
-- YES/NO

DRIVERS DOOR KEY OFF
-- YES/NO

PASS WINDOW LOCKOUT
-- YES/NO

KEY FOB FLASH LIGHTS
-- YES/NO

KEY FOB CHIRP HORN
-- YES/NO

DELAY LOCK OF DOORS
-- YES/NO

PERIMETER LIGHTS
-- YES/NO

EXT LIGHT TIMEOUT
-- 5 to 30 Seconds

DISPLAY DRIVER ID
-- YES/NO

KEY FOB MEMORY SEAT
-- YES/NO

DRIVING POSITION
-- YES

EXIT POSITION
-- YES

TILT MIRROR REVERSE
-- YES/NO
ProCarManuals.com

2-92
Window Lockout Personalization
The number of passenger windows locked out by
the window LOCK switch can be programmed through
the DIC.
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you select YES for PASS WINDOW LOCKOUT,
all three passenger window switches will be locked out
when the window LOCK switch is on.
If you select NO for PASS WINDOW LOCKOUT, only
the two rear passenger window switches will be locked
out when the window LOCK switch is on.
For more information on this feature, see ªWindow
Lockº in the Index.
Security Feedback
You can program the security feedback feature to
change to the following modes:
Mode 1: No feedback when locking or unlocking
the vehicle.
Mode 2: Parking lamps and the DRL will flash twice
when unlocking the vehicle and flash once when locking
the vehicle.Mode 3: Horn chirps when all doors are unlocked
(second unlock button press) and when locking
the vehicle.
Mode 4: Parking lamps and the DRL will flash twice
each time the button with the unlock symbol is pressed;
the horn chirps when all doors are unlocked. Parking
lamps and the exterior lamps flash once and the horn
chirps when locking the vehicle.
You can change these modes by different selections
of the following DIC displays:

KEY FOB LIGHTS FLASH
-- YES/NO

KEY FOB HORN CHIRP
-- YES/NO
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you would like to program your vehicle to Mode 1,
do the following:
1. Select NO for KEY FOB LIGHTS FLASH.
2. Select NO for KEY FOB HORN CHIRP.
ProCarManuals.com