sensor OLDSMOBILE AURORA 2003 Owners Manual

When an air bag inflates, there is dust in the
air. This dust could cause breathing problems
for people with a history of asthma or other
breathing trouble.
To avoid this, everyone in
the vehicle should get out as soon as
it is safe
to do
so. If you have breathing problems but
can’t get out of the vehicle after an air bag
inflates, then get fresh air by opening a
window or a door.
If you experience breathing
problems following an air bag deployment, you
should seek medical attention.
Your vehicle has a feature that will automatically unlock
the doors and turn the interior lamps on when the air
bags inflate
(if battery power is available). You can lock
the doors again and turn the interior lamps
off by
using
ii~e door iock ana inierior iamp conirois.
In many crashes severe enough to inflate an air bag,
windshields are broken by vehicle deformation.
Additional windshield breakage may also occur from the
right front passenger air bag.
Air bags are designed to inflate only once. After an
air bag inflates, you’ll need some new parts for
your air bag system. If you don’t get them, the air
bag system won’t be there to help protect you
in another crash.
A new system will include air bag
modules and possibly other parts. The service
manual for your vehicle covers the need to replace
other parts.
Your vehicle is equipped with an electronic frontal
sensor, which helps the sensing system distinguish
between a moderate frontal impact and a more
severe frontal impact. Your vehicle is also equipped
with a crash sensing and diagnostic module,
which records information about the frontal air bag
system. The module records information about
the readiness of the system, when the system
commands air bag inflation and driver’s safety belt
usage at deployment. The module also records
speed, engine
RPM, brake and throttle data.
1-53
ProCarManuals.com

For a single wiping cycle, move the lever down to MIST.
Hold it there until the wipers start, then release it. The
wipers will stop after one cycle.
If you want more cycles,
hold the lever on MIST longer.
For steady wiping at low speed, move the lever up to
the
LO position. For high-speed wiping, move the lever
up further, to HI.
To stop the wipers, move the lever
to OFF.
You can set the wiper speed for a long or short delay
between wiper cycles. Move the lever up to the first
detent, INT (Intermittent). Turn the band labeled
INT ADJ (Intermittent Adjustment) down toward the
shorter lines for fewer wiper passes per minute. As you
turn the band toward the longer lines, the wiper
cycles per minute will increase.
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
do become damaged, get new blades or blade inserts.
See
Windshield Wiper Blade Replacement on
page
5-59.
Heavy snow or ice can overload your wipers. A circuit
snow or ice to prevent an overload.
\yindrihield, ~~r~f~!Il;/ lcgspn 9~ thl~~! them. !f \/nllr hl=dnc J --’
breaker wi!! stop them unti! the mntnr con!s. C!ear away
RainsenseTM II Wipers
The moisture sensor is mounted on the interior side of
the windshield below the rearview mirror and is used
to automatically operate the windshield wipers.
This system operates by monitoring the amount of
moisture build-up on the windshield. Wipes occur as
needed to clear the windshield depending on the driving
conditions and sensitivity setting. In light rain or snow,
fewer wipes will occur. In heavy rain or snow, wipes will
occur more frequently. The system will operate in the
delay, low speed and high speed modes. If the system is
left on for long periods of time, occasional wipes may
occur without any moisture
on the windshield. This
is normal and indicates that the RainsenseTM system is
activated.
3-9
ProCarManuals.com

The RainsenseTM system is activated by moving the
wiper lever up to the INT position and turning the
INT ADJ band to one
of the five sensitivity levels within
the delay area. The bottom INT ADJ position is the
lowest sensitivity setting, level one. This allows more
rain or snow to collect on the windshield between wipes.
You can increase the sensitivity of the system and the
frequency of wipes by turning the INT ADJ band
away from you to the higher sensitivity levels. The top
position is the highest sensitivity setting, level five.
A single wipe will occur each time you turn the INT ADJ
band to a higher sensitivity level to indicate that the
sensitivity level has been increased.
Notice: The wipers must be turned off when going
through a car wash to avoid damage.
The MIST and wash cycles operate as normal and are
not affected by the RainsenseTM function. The
system can be overridden at any time by manually
changing the wiper control to
LO or HI speed.
Notice: Do not place stickers or other items on the
exterior glass surface directly in front of the
rainsensor. Doing this could cause the rainsensor
to malfunction.
Windshield Washer
The lever on the right side of your steering column also
controls your windshield washer. To spray washer
fluid on the windshield, push the button on the end
of
the lever. The wipers will clear the window and then
either stop or return
to your preset speed. For more
washer cvcles, push and hold the button.
In freezing weather, don’t use your washer
until the windshield is warmed. Otherwise the
washer fluid can form ice on the windshield,
blocking your vision.
Ice build up can block washer nozzles. Remove ice for
proper operation.
If the fluid level in the windshield washer bottle is low,
the message LOW WASHER FLUID will appear on
the
DIC. See Windshield Washer Fluid on page 5-38.
3-1 0
ProCarManuals.com

Wiper-Activated Headlamps
This feature turns on the low-beam headl,amps,
instrument panel cluster backlighting and taillamps after
the windshield wipers have been in use for
approximately six seconds. To operate, the exterior
lamps control must be in AUTO and it must be
dark enough outside.
When the exterior lamps control is in OFF or the
parking lamp position and the windshield wiper control
is on (LO, HI or INT), the HEADLAMPS SUGGESTED
message
will appear on the DIC.
When you turn the key to OFF, the wiper-activated
headlamps will immediately turn off. The wiper-activated
headlamps will also turn off
if you turn the exterior
lamps control to OFF or turn off the windshield wipers.
Headlamps on Reminder
If the exterior lamps control is left on, you’ll hear a
warning chime when you turn the ignition off, remove
the key from the ignition and open the driver’s door.
nrr..+;mrr bllmm:mre* I n--IcI uayrllIIG IIUIIIIIII~ Lalllpa
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the
day. DRL can be helpful
in many different driving
conditions, but they can be especially helpful in the short
periods after
dawn and before s~Jnset. FL!!!~ f~jnctiona!
daytime running lamps are required on all vehicles
first sold in Canada. A
light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
The DRL system will make your high-beam headlamps
come on at reduced brightness in daylight when the
following conditions are met:
The ignition is on,
the exterior lamps control is off, and
e the transaxle is not in PARK (P).
When the DRL are on, only your high-beam headlamps
will be on. The parking lamps, taillamps, sidemarker
and other lamps won’t be on.
With your headlamp control in AUTO when it is dark
enough outside, your low-beam headlamps will
automatically come on. The other lamps that turn on
with your headlamps will also turn on. When it is bright
enough outside, the regular lamps will go
off, and
your high-beam headlamps change to the reduced
brightness of DRL.
To turn off all exterior lighting at night when you are
parked, turn the exterior lamps control all the way toward
OFF. The DRL will turn on automatically and the
HEADLAMPS SUGGESTED message will be displayed
on the DIC when you move the transaxle out of
PARK (P).
3-1 5
ProCarManuals.com

If the exterior lamps control is in the parking lamps
position at night, only the parking lamps will be on.
If the
transaxle is out of PARK
(P), only the parking lamps
will be active and the HEADLAMPS SUGGESTED
message will be displayed on the DIC.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Headlamp System
The automatic headlamp system will keep your
headlamps on when it is dark outside and the ignition
is
in ON.
It’s possible that your headlamps may go out if you
drive from a dark area into a bright area like a lighted
parking lot.
If this happens, turn on your headlamps with
the exterior lamps control.
Light Sensor
Your automatic headlamps and DRL work with the light
sensor on top of the instrument panel. Don’t cover it
up.
If you do it will read “dark” and the automatic
headlamp lighting will turn on.
Fog Lamps
To turn on only the front
fog lamps, turn the fog
lamp band to the single fog
lamp symbol. To turn on both the front and rear fog
lamps, turn the fog
lamp band to the double
fog lamp symbol.
Turning on the front fog lamps only will automatically
activate the parking lamps. Turning on the front and rear
fog lamps will automatically activate the parking lamps
and headlamps.
To turn
off the fog lamps, turn the band to OFF. The
front fog lamps will also turn
off when you turn on your
high-beam headlamps, but
will turn on again when
you switch to low beams.
Continuous use of the fog lamps will shorten bulb life
Limit use as necessary.
3-1 6
ProCarManuals.com

Do not cover the solar sensor located in the center of
the instrument panel, near the windshield. For more
information on the solar sensor, see “Sensors” later
in
this section.
To change the automatic climate control display from an
English display to a metric display, push the
OFF
button located in the Driver Information Center (DIC) for
several seconds. The display in the
DIC will also
change from an English to a metric display.
To return to
an English display, repeat the procedure.
Manual Operation
FAN: Turn the right knob clockwise or counterclockwise
to increase or decrease the fan speed. Turning this
knob cancels automatic operation and places the system
in manual mode. Press the knob to return to automatic
operation.
Temperature Control: Maintain the temperature inside
the vehicle using the red and blue arrows located
below the digital display. Push the red arrow for a
warmer temperature level and the blue arrow for
a cooler temperature level. Your selected temperature
setting will be shown on the digital display for five
seconds, and then the outside temperature will be
displayed. To change
the current mode, use the left knob
to select
one of the following:
OFF: Turning the left knob to OFF will cause the fan to
turn
off and the airflow to be directed through the
floor outlets. The display will show the outside
temperature when the system is set to OFF.
/I‘ (Vent): This mode directs air to the instrument
panel outlets. #
(Bi-Level): This mode directs approximately half of
the air to the instrument panel outlets, and then
directs most of the remaining air to the floor outlets.
Some air may be directed toward the windshield.
In automatic operation, cooler air is directed to the upper
outlets and warmer air to the floor outlets.
I# (Floor): This mode directs most of the air to the
floor outlets with some air directed to the outboard
outlets (for the side windows) and some air directed to
the windshield.
The left knob can also be used to select the defog or
defrost mode. Information on defogging and defrosting
can be found later in this section.
3-24
ProCarManuals.com

(Recirculation): Press this button to limit the
amount of outside air coming into the vehicle.
It can be
used to prevent outside air and odors from entering
your vehicle or to help heat or cool the air inside your
vehicle more quickly. Press this button to turn the
recirculation mode on or
off. When the button is pressed,
an indicator light will come on. The recirculation mode
cannot be used with the defrost mode.
a AK (Air Conditioning): Press this button to
override the automatic system and turn the air
conditioning system on or
off. When A/C is pressed, an
indicator light in the button will come on to let you
know that air conditioning is activated. When in
AUTO
the air conditioning compressor will come on
automatically, as necessary.
On hot days, open the windows to let hot inside air
escape; then close them. This helps reduce the time it
takes for your vehicle to cool down. It also helps
the system to operate more efficiently.
For quick cool down on hot days, do the following:
1. Select the vent mode.
2. Select the recirculation mode.
3. Select NC.
4. Select the coolest temperature.
5. Select the highest fan speed.
Using these settings together for long periods of time
may cause the air inside of your vehicle to become too
dry. To prevent this from happening, after the air in
your vehicle has cooled, turn the recirculation mode off.
The air conditioning system removes moisture from
the air,
so you may sometimes notice a small amount of
water dripping underneath your vehicle while idling or
after turning off the engine. This is normal.
Sensors
The solar sensor on your vehicle monitors the solar
radiation and the air inside of your vehicle, then uses the
information to maintain the selected temperature by
initiating needed adjustments to the temperature, the fan
speed and the air delivery system. The system may
also supply cooler air to the side of the vehicle facing the
sun. The recirculation mode will also be activated, as
necessary no not cover the solar sensor located in the
center of the instrument panel, near the windshield,
or the system will not work properly.
3-25
ProCarManuals.com

Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows the air bag symbol. The system
checks the air bag’s electrical system for malfunctions.
The light tells you
if there is an electrical problem.
The system check includes the air bag sensors, the air
bag modules, the wiring and the crash sensing and
diagnostic module. For more information on the air bag
system, see
Air Bag Systems on page 1-47.
This light will come on
when you start your
vehicle, and it will flash for
several seconds. Then
the light should go out. This means the
system is ready.
If the air bag readiness light stays on after you start the
vehicle or comes on when you are driving, your air
bag system may not work properly. Have your vehicle
serviced right away.
If the air bag readiness light stays on after you
start your vehicle,
it means the air bag system
may not be working properly. The air bags in
your vehicle may not inflate in a crash,
or they
could even inflate without a crash.
To help
avoid injury to yourself or others, have your
vehicle serviced right away if the air bag
readiness light stays on after you start your
vehicle.
The air bag readiness light should flash for a few
seconds when you turn the ignition key to
ON. If the
light doesn’t come on then, have it fixed
so it will
be ready to warn you
if there is a problem.
On the
DIC an AIR BAG PROBLEM message will be
displayed when there is a problem with the air bag
system. See
DIC Warnings and Messages on page 3-50
for more information.
3-34
ProCarManuals.com

Fuses
1
2
3
4
5
6 - 1
Usage
Not Used
Accessory
Windshield Wipers
Not Used Left Low-Beam Headlamp
Right Low-Beam Headlamp
Spare Fuses
8
9
10
11
12
13
14
15
16
17
18
19
20 21
22
23
24
25
26
Usage Powertrain Control Module Battery
Right High-Beam Headlamp
Left High-Beam Headlamp
Ignition
1
Not Used
Transaxle Cruise Control Direct Ignition System
Injector Bank #2
Not Used
Not Used
Powertrain Control Module Ignition
Oxygen Sensor
Injector Bank
#I
Auxiliary Power
Cigarette Lighter Fog Lamps/Daytirne Running Lamps
Horn
Air Conditioning Clutch
5-93
ProCarManuals.com

Seats Head Restraints
............................................ 1-7
Heated Seats
............................................... 1-5
Manual Lumbar
............................................. 1-3
Manual Passenger
......................................... 1-2
Memory
..................................................... 2-48
Power Lumbar
.......................................... 1-4
Power Seats
.................. ................... 1-2
Reclining Seatbacks
...................................... 1-5
Securing a Child Restraint
Designed for the LATCH System
................... 1-42
Rear Seat Position
...................................... 1-42
Right Front Seat Position
.............................. 1-44
Security Feedback
.................................... 2-8, 3-56
Security While You Travel
.................................. 7-5
Sensors
......................................................... 3-25
Service
........................................................... 5-3
Adding Equipment to the Outside of Your
Vehicle
.................................................. 5-4
Doing Your Own Work
................................... 5-4
Engine Soon Light
....................................... 3-39
Publications Ordering Information
..................... 7-9
Service Manuals
............................................... 7-9
Setting Preset Stations
.................................... 3-61
Setting Preset PTYs
........................................ 3-64
3tiVibt UUiIC11113 /-1u P-.- ..-- n . .II-L.-- 7 4n .............................................
Setting the Time .......................................... 3-59 Setting
the Tone (Bassnreble)
........... .... 3-61
Sheet Metal Damage
........................ .... 5-87
Shifting Into Park (P)
....................................... 2-30
Shifting Out
of Park (P) ................................... 2-32
Skidding
........................................................ 4-15
Some Other Rainy Weather Tips
....................... 4-20
Specifications. Capacities
............................... 5-1 00
Speedometer .................................................. 3-32
Starter Switch Check
....................................... 6-11
Starting Your Engine
....................................... 2-24
Steering
........................................................ 4-10
Steering in Emergencies
.................................. 4-12
Steering, Suspension and Front Drive Axle Boot
and Seal Inspection
..................................... 6-13
Steering Tips
.................................................. 4-11
Steering Wheel Climate Controls
....................... 3-28
Steering Wheel Controls, Audio
......................... 3-74
Storage Areas
Convenience Net
......................................... 2-46
Front Storage Area
...................................... 2-45
Glove
Box .................................................. 2-45
Rear Storage Area
....................................... 2-46
~LWIIII~ ii-e rrat III~: a~lu loois 3-f~
Storing the Spare Tire and Tools ....................... 5-80
Stuck in Sand, Mud, Ice or Snow
...................... 4-32
Sun Visors
............................... ........... 2-18
Sunroof
................................... ....... 2-47
n1 .... Pl~ I T . IT - -- ..........................
13
ProCarManuals.com