wheel OLDSMOBILE INTRIGUE 1998 Service Manual

If a Tire Goes Flat
I --
10. Then replace the pressure cap. At any time during
this procedure if coolant begins to flow out
of the
filler neck, reinstall the pressure cap. Be sure the
arrows on the pressure cap line up like this.
1 1. Check the coolant in the recovery tank. The level
in the coolant recovery tank should be at the
HOT
mark when the engine is hot or at the COLD mark
when the engine
is cold. It’s
unusual for a tire to “blow out” while you’re driving,
especially if
you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if
you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create
a drag that
pulls the vehicle toward that side. Take your foot
off
the accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake
to a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like
a skid and may require the same correction you’d use
in a skid. In any rear blowout, remove your foot from
the accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part shows how to use your
jacking equipment to change a flat tire safely.
5-24
ProCarManuals.com

Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly
to a level place. Turn on your hazard
warning flashers.
Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find a level place to change your tire.
To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle, at the opposite end.
i
The following steps will tell you how to use the jack and
change a
tire.
5-25
ProCarManuals.com

A
C
Turn the nut holding the jack to the left and remove it.
Then remove the jack and wrench. The
tools you'll be using include the jack (A), extension
and protectodguide
(B) and wheel wrench (C).
5-27
ProCarManuals.com

1. Using the wheel wrench, remove plastic nut, loosen all the wheel nuts. Don't remove them yet.
2. Turn the jack handle to the left to raise the jack lift
head
a few inches.
#
J REAR EDBE OF FRONT
WHEEL OPENING
For jacking at the vehicle's front location, put the
jack lift head about
8 inches (20 cm) from the rear
edge of the front wheel opening
or just behind the
two bolts as shown.
ProCarManuals.com

OFF - SET
FRONT EDGE OF
REAR WHEEL
OPENING
For jacking at the vehicle’s rear location, put the jack
lift head about
6 inches (15 cm) from the front edge
of the rear wheel opening or just behind the off-set
as shown.
Put the compact spare tire near
you.
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips
off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle
fall. To help avoid personal
injury and vehicle damage, be sure
to fit the jack
lift head into the proper location before raising
the vehicle.
5-29
ProCarManuals.com

i 3. Raise the vehicle by turning the jack handle to the
right. Raise the vehicle far enough
off the ground for
the spare tire
to fit under the vehicle.
4. Remove all wheel nuts and take off the flat tire.
5-30
ProCarManuals.com

5. Remove any rust or dirt
from the wheel bolts,
mounting surfaces and spare wheel.
A CAUTION:
Rust or dirt on the wheel, or on the parts to
which
it is fastened, can make the wheel nuts
become loose after
a time. The wheel could come
off and cause an accident. When you change
a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle.
In an
emergency, you can use
a cloth or a paper towel
to do this; but be sure to use a scraper or wire
brush later, if you need to, to get all the rust or
dirt off.
I
I A CAUTION:
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall
off, causing a serious accident.
6. Replace the wheel nuts with the rounded end of the
nuts
toward the wheel. Tighten each nut by hand
until the wheel is held against the hub.
5-31
ProCarManuals.com

7. Lower the vehicle by turning the jack handle to the
lee. Lower the jack completely.
8.
9.
Tighten the wheel nuts
My in a crisscross
sequence as shown.
Replace
plastic nut caps
snug tight with hand.
Using wheel wrench.
tighten caps an
,additional 114 tarn.
Incorrect wheel nuts or improperly tightened
wheel nuts can cause the wheel to become loose
and even come
off. This could lead to an accident.
Be sure to use the correct wheel nuts.
If you have
to replace them, be sure to get new
GM original
equipment wheel nuts.
Stop somewhere as soon as you can and have
the nuts tightened with
a torque wrench to
100 lb-ft (140 Nom).
I
5-32
ProCarManuals.com

NOTICE:
Improperly tightened wheel nuts can lead to
brake pulsation and rotor damage.
To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper
torque specification.
Storing the Flat Tire and Tools
Storing a jack, a tire or other equipment in the
passenger compartment
of the vehicle could
cause injury. In
a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place. After you’ve
put the compact spare tire on your vehicle,
you’ll need
to store the flat tire in your trunk. Use the
following procedure to secure the flat tire in the trunk.
When storing
a full-size tire you must use the extension
to help avoid wheel surface damage. Use extension and
protector/guide located
in foam holder.
To store a full size tire, place tire valve stem facing down,
with the protectodguide through a wheel bolt hole, then
remove protector and attach retainer securely. When
reinstalling compact spare put
the protector/guide back in
foam holder. Store the cover as far forward as possible.
5-33
ProCarManuals.com

Compact Spare Tire
Although the compact spare tire was fully inflated
when your vehicle was new, it can lose air after a time.
Check the inflation pressure regularly. It should be
60 psi (420 kPa).
After installing the compact spare on your vehicle,
you should stop as soon as possible and make sure
your spare tire is correctly inflated. The compact
spare is made to perform well at speeds up to
65 mph
(105 Wh) for distances up to 3,000 miles (5 000 km),
so you can finish your trip and have your full-size tire
repaired or replaced where you want. Of course, it’s
best to replace your spare with a full-size tire as soon
as you can. Your spare will last longer and be in good
shape in case you need
it again.
NOTICE:
When the compact spare is installed, don’t take
your vehicle through an automatic car wash with
guide rails. The compact spare can get caught on
the rails. That can damage the tire and wheel,
and maybe other parts
of your vehicle.
Don’t use your compact spare on other vehicles.
And don’t mix your compact spare tire or wheel with
other wheels or tires. They won’t fit. Keep your spare
tire and its wheel together.
NOTICE:
Tire chains won’t fit your compact spare. Using
them can damage your vehicle and can damage
the chains too. Don’t use tire chains on your
compact spare.
5-35
ProCarManuals.com