light OLDSMOBILE SILHOUETTE 1996 Owner's Guide

Low Coolant Light
I i LOW
If this light comes on,
your system is low on
coolant and the engine
may overheat.
Malfunction Indicator Lamp
(Service Engine
Soon Light)
SERVICE
ENGINE SOON
Your Oldsmobile is
equipped with a computer
which monitors operation
of the
fuel, ignition and
emission control systems.
To prevent damage to your engine, immediate action
is required.
See “Engine Coolant”
in the Index and have your
vehicle serviced
as soon as possible. This
system is called
OBD I1 (On-Board
Diagnostics-Second Generation) and
is intended to
assure that emissions are at acceptable levels for the life
of the vehicle, helping to produce
a cleaner
environment. The
SERVICE ENGINE SOON light
comes on to indicate that there is a problem and service
is required. Malfunctions often will be indicated by the
system before any problem is apparent, which may
prevent more serious damage to your vehicle. This
system is also designed to assist your service technician
in correctly diagnosing any malfunction.
ProCarManuals.com

I NOTICE:
If you keep driving your vehicle with this light
on, after a while, your emission controls may not
work as well, your fuel economy may not be
as
good and your engine may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running. If the light doesn’t come on, have
it repaired.
This light will also come on during
a malfunction in one
of two ways:
0
0
Light Flashing -- A misfire condition has been
detected. A misfire increases vehicle emissions and
may damage the emission control system
on your
vehicle. Retailer or qualified service center diagnosis
and service is required.
Light On Steady -- An emission control system
malfunction has been detected on your vehicle.
Retailer or qualified service center diagnosis and
service may be required. The
following
may prevent more serious damage to
your vehicle:
0 Reduce vehicle speed.
0 Avoid hard accelerations.
0 Avoid steep uphill grades.
0 If towing a trailer, reduce the amount of cargo being
hauled as soon
as it is possible.
If the light stops flashing and remains on steady, see “If
the Light
Is On Steady” following.
If the light continues to flash, when it is safe to do so,
stop the vehicle. Put your vehicle in PARK (P). Turn the
key off, wait at least 10 seconds and restart the engine.
If the light remains on steady, see
“If the Light Is On
Steady” following.
If the light is still flashing follow the
previous steps, and drive the vehicle to your retailer
or
qualified service center for service.
ProCarManuals.com

If 3 Light Is On Steady
IOU may be able to correct the emission system
malfunction by considering the following:
Did you just put fuel into your vehicle?
If
so, reinstall the fuel cap, making sure to fully install
the cap. The diagnostic system
can determine if the fuel
cap has been
left off or improperly installed. This will
allow fuel to evaporate into the atmosphere.
A few
driving trips should turn the light off.
Did you just drive through a deep puddle of water?
If
so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out. A few driving trips should turn the light off.
Are you low on fuel?
As your engine starts to run out of fuel, your engine may
not run as efficiently
as designed since small amounts of
air are sucked into the fuel line causing a misfire. The
system can detect this. Adding fuel should correct this
condition. Make sure
to install the fuel cap properly.
It will take
a few driving trips to turn the light off. Have
you recently changed brands of fuel?
If
so, be sure to fuel your vehicle with quality fuel (see
“Fuel”
in the Index). Poor fuel quality will cause your
engine not to run as efficiently
as designed. You may
notice this
as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience this condition, change the fuel brand
you use. It will require at least one full tank of the
proper fuel to turn the light off.
If none of the above steps have made the light turn off,
have your retailer or qualified service center check the
vehicle. Your retailer has the proper test equipment and
diagnostic tools to fix any mechanical or electrical
problems that may have developed.
ProCarManuals.com

Low OilLi -
LOW
OIL
If this light comes on, it
means your engine is low
on oil.
Power Sliding Door Warning Light
With the optional power
sliding door, the sliding
door ajar symbol on your
instrument panel will come
on
if your sliding door is
not completely closed.
You need to check the
oil level right away. Driving your
vehicle without enough oil can cause extensive engine
damage. Have your vehicle serviced immediately. If you shift the transaxle out of PARK (P) while the
sliding door is open or
in the process of closing, and the
power sliding door
ON/OFF switch is in the ON
position, the power sliding door warning light will flash
and a buzzer will sound. This is
a warning that the
sliding door is not completely closed.
ProCarManuals.com

If you shift the transaxle out of PARK (P) and
accelerate before the power sliding door latches
closed, the door may reverse to the open position.
A child or others could fall out of the vehicle and
be injured. Always make sure the power sliding
door
is closed and latched before you drive away.
If you manually slam the power sliding door shut when
the ignition is on, the power sliding door warning light
may come
on and stay on. To turn the light off, reopen
and close the door using either power door switch, or
manually open and close
the door again more slowly.
Lift,. ~ Aja:-- Wan 19 Light
-1
The liftgate ajar symbol on
your instrument panel will
come on if your liftgate is
not completely closed.
ProCarManuals.com

Low Fuel Warning Light
I
‘F
1/2
This light will also come on when you turn on the
ignition, but the engine
is not running, to show you it is
working. If
it doesn’t come on as you start your vehicle,
have it fixed right away.
When there
is between 3 gallons (1 1 L) and 0.5 gallon
(1.8 L) of fuel left in the tank, the warning light next to
the fuel symbol will go
on.
ProCarManuals.com

On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let
hot, inside air escape. For all settings,
adjust the temperature control lever and fan speed
as desired.
Press the RECIRC button
to get maximum cooling or
quick cool-down on very hot days. It should not be used
for long periods of time because the air may become too
cold and dry.
When the temperature outside is above freezing,
the air
conditioner compressor will automatically condition the
air when you press RECIRC (the A/C indicator light
will glow),
DEFOG or DEF (the A/C indicator light will
not glow).
Press A/C (the
A/C indicator light will glow) to condition
the air when you press UPPER, BI-LEV or LOWER. To
turn
off the air conditioner compressor in these settings,
press A/C again (the indicator light will go
off>.
Each time you turn on the ignition, the air conditioner
will default to the setting you had selected before last
turning off the ignition.
When the air conditioner compressor is on,
you may
sometimes notice slight changes
in your vehicle’s engine
performance and power. This is normal. The system
is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air,
so
you may sometimes notice water dripping from under
your vehicle when
it is idling or after it has been turned
off. This is normal.
T’
Slide the temperature lever to the right to warm the air.
In the LOWER mode, outside air will be brought
in and
sent through
the floor outlets. The heater works best if
you keep your windows closed while using
it.
ProCarManuals.com

Rear Window Defogger
Press R. DEF (Rear Defog) to warm the defogger grid on
the rear window. The indicator light will glow while the
rear window defogger is operating. The rear window
defogger will turn
off automatically after about 10 minutes
of use. If you
turn it on again, the defogger will operate
for about five minutes only. You can also turn the defogger
off by turning off the ignition or pressing the switch again.
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
I NOTICE:
Don’t use a razor blade or something else sharp
on the inside
of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn’t be covered
by your warranty.
Audio Systems
Your Delco@ audio system has been designed to operate
easily and give years
of listening pleasure. You will get
the most enjoyment out
of it if you acquaint yourself
with it first. Find out what your Delco system can do
and how to operate all its controls, to be sure you’re
getting the most out of the advanced engineering that
went into it.
Setting the Clock for AM-FM Stereo
Press SET. Within five seconds, press and hold SEEK
down arrow
until the correct hour appears. Press and
hold SEEK up arrow
until the correct minute appears.
Setting the Clock for AM-FM Stereo with
Cassette Tape Player
Press SET. Within five seconds, press and hold SEEK
left arrow until the correct hour appears. Press and hold
SEEK right arrow until the correct minute appears.
Setting the Clock for AM-FM Stereo with
Compact Disc Player
Press SET. Within five seconds, press and hold SEEK
until the correct hour appears. Press and hold SCAN
until the correct minute appears.
ProCarManuals.com

Adjusting the Speakers
BAL: Turn the control behind the upper knob to move
the sound
to the left or right speakers. The middle
position is a detent and balances the speakers.
FADE: Turn the control behind the lower knob to move
the sound to the front or rear speakers. The middle
position is a detent and balances
the speakers.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
30 to 45 minutes long on each side. Tapes longer than
that are
so thin they may not work well in this player.
The longer side with the tape visible goes in first. If
you
hear nothing or hear just a garbled sound, it may not be
in squarely. Press STOP-EJECT to remove the tape and
start over.
While the tape is playing, use the
VOL, FADE, BAL,
TREB and
BASS controls just as you do for the radio.
Other controls may have different functions when
a tape
is inserted. The display will show an
arrow to show
which side
of the tape is playing. Note
that cassette tape adapter kits for portable compact
disc players will not work in your cassette player. These
adapters will cause an error message to show on
the
display, and the adapter cassette will be ejected.
FORWARD: Press the right arrow to rapidly advance
the tape. It will continue forwarding until you press the
right arrow again lightly.
REVERSE: Press the left arrow to rapidly reverse the
tape. It will continue reversing
until you press the left
arrow again lightly.
PROG-RCL: Press this knob to hear the other side of a
tape that is playing.
STOP-EJECT Press this button to remove the tape or
stop playing the tape and switch
to the radio.
CLN: This message may appear on the display. If it
does, your cassette tape player needs to be cleaned. It
will still play tapes, but you should clean it as soon as
possible to prevent damage to your tapes and player.
See “Care of Your Cassette Tape Player” in the Index.
After you clean the player, press and hold STOP-EJECT
for five seconds to reset the CLN indicator. The radio
will display
--- to show the indicator was reset.
3-13
ProCarManuals.com

Setting the Tone
BASS:
Press this button up to increase bass and down
to decrease
it. Press the center of the control to get the
factory preset midpoint.
TREB: Press this button up to increase treble and down
to decrease it. If a station is weak or noisy, press the
button down to reduce the noise. Press the center of the
control to get the factory preset midpoint.
Adjusting the Speakers
BALANCE:
Turn the control behind the upper knob to
adjust the sound between the right and left speakers.
FADE: Turn the control behind the lower knob to move
the sound between the front and rear speakers.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
30 to 45 minutes long on each side. Tapes longer than
that are
so thin they may not work well in this player.
While the tape is playing, use the
VOL, FADE, TREB
and BASS controls just
as you do for the radio. The
display will show an arrow to show which side of the
tape is playing. When the down indicator arrow is lit,
selections listed
on the bottom side of the cassette are
playing. When the
up arrow is lit, selections listed on the top
side
of the cassette are playing. The tape player
automatically begins playing the other side when it
reaches the end of
the tape.
This system has automatic Dolby Noise Reduction to
reduce background noise on tapes encoded with Dolby
NR. Dolby Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks
of
Dolby Laboratories Licensing Corporation.
PROG (1): Press this button to play the other side of
the tape.
CrO2 (2): This button sets the tape bias. When playing
high-bias chrome or metal tapes, press the Cr02 button
to turn
the Cr02 display on. When playing standard bias
tapes, press again to turn the light
off.
REV (5): Press this button to reverse the tape rapidly.
Press
REV or PROG to return to playing speed.
The radio will play the last-selected station while
the tape reverses.
FWD: Press the SCAN button to advance quickly to
another part
of the tape. Press FWD or PROG to return
to playing speed. The radio
will play the last-selected
station while
the tape advances.
ProCarManuals.com