ABS OLDSMOBILE SILHOUETTE 1997 User Guide

NOTE: INSTALL OF BAG - BOTTOM FIRST
TOOL STORAGE
BAG & TOOLS
Replace all jacking tools as they were stored in the jack
storage compartment and replace the compartment
cover.
To replace the cover, line up the tabs on the right
of the cover with
the slots in the cover opening. Push the
cover in place and push down the tab
so that it rests in
the groove. This secures the cover in place. Unless
you have
the plastic “bolt-on” wheel covers, be
sure to also store the nylon
nut caps and the center cap.
When
you replace the compact spare with a full-size
tire, replace the bolt-on wheel covers or
the nylon nut
caps and
the center cap. Tighten them “hand tight” over
the
wheel nuts, using the folding wrench.
Compact Spare Tire
Although the compact spare tire was fully inflated
when your vehicle was new, it can lose air after a time.
Check the inflation pressure regularly. It should be
60 psi (420
kPa).
After installing the compact spare on your vehicle,
you should stop
as soon as possible and make sure
your spare
tire is correctly inflated. The compact
spare is made to perform well at speeds up to
65 mph
(105 km/h) for distances
up to 3,000 miles (5 000 km),
so you can finish your trip and have your full-size tire
repaired or replaced where you want. Of course, it’s best
to replace your spare
with a full-size tire as soon as you
can. Your spare will last longer and be
in good shape in
case you need it again.
5-32
ProCarManuals.com

Air Cleaner
The air cleaner is located at the front of the engine
compartment (on the left side
of the vehicle), under the
engine coolant reservoir.
Checking or Replacing the Air Cleaner
1.
2.
3.
4.
Unlatch the two hooks on top of the air
cleaner housing.
Turn back the air inlet panel and rest it on top of the
housing. The air intake tube is designed to flex back;
you do not need to disconnect it.
After replacing the air cleaner filter, seat the tabs on
the bottom
of the panel into the slots at the bottom.
Latch the hooks to secure the panel in place.
If the
panel moves easily, check that the tabs
are seated
correctly in the slots.
-
Operating the engine with the air cleaner off can
cause you
or others to be burned. The air cleaner
not only cleans the air,
it stops flame if the engine
backfires.
If it isn’t there, and the engine
backfires, you could be burned. Don’t drive with
it off, and be careful working on the engine with
the air cleaner off.
6-15
ProCarManuals.com

5. Unhook the electrical connector by lifting up the
blue tabs and pulling the bulb out.
6. Replace the new bulb through the black retainer ring
and into the electrical connector.
Push the bulb
firmly enough
so that the blue tabs hook over the tab
on the bulb.
7. Carefully put the bulb assembly back into the lamp
housing and tighten the
black retainer ring in place.
Be careful not to darnage the bulb on the headlamp
aiming bar.
6-33
ProCarManuals.com

8. Align the pins on the bottom of the headlamp
assembly with
the holes in the lamp support bracket
while placing the holes
in the assembly over the
bolts where the wing nuts attach.
9. Replace and tighten the wing nuts.
10. Replace the parkinghurn signal lamp assembly by
lining up the tabs at the back
of the assembly with
the holes
in the fender.
1 1. Tighten the bolt connecting the parkinghrn signal
lamp assembly. Be sure the tab from the
parkinghurn signal
lamp assembly is inboard of the
tab from the headlamp assembly.
Front Parking/Turn Signal Lamps
1. Open the hood.
2. Remove the thumb screw attaching the parkingkurn
signal lamp assembly
to the headlamp assembly.
3. Pull the parkinghurn signal lamp assembly away
from the body.
6-34
ProCarManuals.com

4. Unscrew the bulb sockets from the lamp assembly
by pressing the tab while turning counterclockwise.
7. To replace the lamp assembly, line up and insert the
tabs on the back
of the assembly with the slots in the
fender. Engage the lower clip
on the front of the
5. Replace the bulb by pulling the old one out and lamp assembly, keeping the upper tab on the
6. Line up the tabs on the sockets with the gaps in the
gently pushing the
new one into the lamp socket. parkinghm signal lamp assembly inboard of
the
socket holes and screw the bulb sockets back into the 8. To align the parking/turn signal lamp assembly with the
lamp housing until an audible click
is heard (the tab headlamp assembly, lift up the parking/turn signal lamp
popping back out). assembly until the upper
edge is contacting the fender.
headlamp bracket tab.
9. Fasten the parkinghurn signal lamp assembly
to the
headlamp assembly with the thumb screw used in
Step
1.
6-35
ProCarManuals.com

Front Sidemarker
1. Open the hood.
2. Remove the thumb screw attaching the parking/turn
signal lamp assembly
to the headlamp assembly.
3. Pull the parkinghurn signal lamp assembly away
from the body.
4. Unscrew the bulb sockets from the lamp assembly
by turning counterclockwise.
5. Replace the bulb by pulling the old one out and
gently pushing the new one into the lamp socket.
6. Line up the tabs on the sockets with the gaps in the
socket holes
and screw the bulb sockets back into the
lamp housing.
6-36
ProCarManuals.com

7. To replace the lamp assembly, line up and insert the
tabs on the back of the assembly with the slots in the
fender. Engage the lower clip on the front of the
lamp assembly, keeping the upper tab on the
parkinghrn signal lamp assembly inboard of the
headlamp bracket tab.
8. To align the parking/turn signal lamp assembly with the
headlamp assembly,
lift up the parking/turn signal lamp
assembly until the upper edge is contacting the fender.
9. Fasten the parking/turn signal lamp assembly to the
headlamp assembly with the thumb screw used in
Step
1.
Taillamps
1. Open the liftgate.
2. Remove the two screws from the taillamp housing
on the inboard side.
3. Pull off the entire taillamp housing. The locator/retaining
pins on the outboard side are part
of the lamp assembly
and will remain intact during removal.
4. Remove the bulb holder by pressing the four retaining
tabs and pulline the holder away from the assembly.
6-37
ProCarManuals.com

5. Replace the bulb(s) by pulling the old one(s) out and
gently pushing the new one(s)
into the bulb holder socket.
Windshield Wiper Blade Replacement
A. Tail bulb
B. Back-up bulb
C. Signal bulb
D. Stophail bulb
6. Snap the bulb holder back into place ensuring all
retaining tabs are properly over the bulb holder tabs.
7. Reinstall the taillamp assembly by inserting the
outboard locatinghetaining pins
until the lamp is
seated. Secure with thc inboard screws.
For any bulb changing procedure
not listed in this section,
contact your Oldsmobile retailer service department. Replacement
blades for your vehicle are
24 inches
(60 cm) in length. They come in different types and are
removed
in different ways. Here's how to remove the
type with
a release clip:
I. Turn the wipers on to the lowest intermittent setting.
2. Turn off the ignition while the wipers are at the outer
positions
of the wipe pattern. The blades are more
accessible
for removal/replacement while in
this position.
6-38
ProCarManuals.com

Appearance Care Materials Chart
PART NUMBER
I IO50 17:
I 10501 73
I 1050 174
~--
SIZE DESCRIPTION I USAGE
23 in. x 25 in. Polishing Cloth - Wax Treated Exterior Polish
2.75
sq. ft. Chamois Shines vehicle without scratching
16 oz. (0.473 L) Tar and Road Oil Remover Also removes old waxes and polishes
16
oz. (0.473 L)
Exterior cleaner and polish
Magic
Mirror Cleaner Polish 1 gal. (3.785 L) Removes
soil and black marks White Sidewall Tire
Cleaner
16 oz. (0.473 L)
Removes rust and corrosion
Chrome Cleaner and Polish
32
oz. (0.946 L) I Vinyl Cleaner
Spot and stain removal
1050427
Exterior wash Wash and
Wax Concentrate
16 oz. (0.473 L) 1052870 Cleans grease,
grime and smoke film
Glass Cleaner 23 02. (0.680 L)
1052918""
Cleans
vinyl, cloth, tires and mats
Multi-Purpose
Powdered Cleaner 16 oz. (0.473 L) 1052925 Protects
vinyl, leather and rubber Armor All TM Protector
8 oz. (0.237 L)
I 1052929 I 16 OZ. (0.473 L) I Wheel Cleaner I Spray on wheel cleaner I
1052930
Cleans
vinyl, leather and rubber Armor All TM Cleaner 16 oz. (0.473 L) 12345002"" Attracts and
absorbs soils Capture
Dry Spot Remover
8
oz. (0.237 L)
I 12345725 I 12 02. (0.354
L) I Silicone Tire Shine I
~~
Shines tires I I I I
t 12377964 I 16 oz. (0.473 L) I Cleaning Wax I Protects finish and removes fine scratches I
I 12377966 I 16 oz. (0.473 L) I Finish Enhancer I SDot cleans paint and gives high luster I ~
See your General Motors Parts Department for these products. 'i':kNo\
t recommended for use on instrument panel vinyl.
See "Fluids and Lubricants" in the Index.
6-54
ProCarManuals.com

/ -.
FUSE USAGE CHART
BREAKERS
ELEC PRNDL RR DEFOG ELC
HEADlAMP
20
10 CRUISE 10 TlSlG 15 SIR 10 IGN 1 10 PSD
10 25
‘a 25
25 PWR OTR VENT RR HVAC FR$~~~~~~w’ SUNROOF HVAC/DRL
10
20 10
PIM WDQ/RR 2 10 M 20 FRT WPR WSHR SWC ACCY MALURADIO/DC RR WPR WSHR BCM PRGRM -- I PWGiAT, I HAZARD 15 STOP LAMP 15
L 20 PWR LOCK RR PWR SCKT ABS MOL BATT 20 10
FRT HVAC HI 20 2 K ABS SOL SWC BACK LIGHT
For More Information, See Owner’s Manual . Printed in 10250877 /
CIRCUIT BREAKERS
FRT HVAC
HI BLWR ......... Blower Motor Resistor
HEADLAMP
...... DRL Control Module,
Headlamp Dimmer Switch and
Headlamp Switch
PWR SEATFSD
... 6-way Power Seat(s) and Rear
Side Door Actuator Motor
PWR WDO/RR VENT
............ Front Power Windows
FUSES
ABS MDL BATT ... Electronic Brake Traction
ABS
SOL ......... LH and RH Front Brake
ABS/TCS
IGN ..... Electronic Brake Control Relay
BCM
PRGRM ..... Body Control Module (BCM)
CIGARDLC
...... Cigarette Lighter and Data
CRUISE
.......... Cruise Control Module, Switch
CTSY LAMP
...... BCM
DRL
............. DRL Control Module
ELC
............. Electronic Level Control (ELC)
Air Compressor and ELC Relay
ELEC PRNDL
..... Instrument Cluster to PRNDL
Indicators Control Module
(EBTCM)
Solenoid Valve
and EBTCM
Link Connector (DLC)
and Release Switch
FRT HVAC
LOW/MED BLWR
. Heater-A/C Control
FRT PWR SCKT
... Front Electric Accessory Plug
Housing
Motor and Switch
FRT
WPR/WSHR
. . Windshield Wiper/Washer
HAZARD
......... Turn Signal Switch
6-58
ProCarManuals.com