ESP OPEL COMBO 2010 User Guide

108 Driving and operationSaving Fuel, Protecting the
Environment Trend-setting technology
Environmentally friendly and mainly
recyclable materials were used when your
vehicle was being developed and
manufactured. The production methods
used to make your vehicle are also
environmentally-compatible.
Recycling of production wastes keeps the
circulation of material closed. Reduction of
energy and water requirements also helps
to conserve natural resources.
A highly advanced design means that your
vehicle can be easily disassembled at the
end of its working life, and the individual
materials separated for subsequent re-use.
Materials such as asbestos and cadmium
are not used. The refrigerant in the air
conditioning system 3 is CFC-free.
New painting techniques employ water as
a solvent. End-of-life vehicle recovery
Information on end-of-life vehicle recovery
centres and the recycling of end-of-life
vehicles is available at www.opel.com.
Energy and environment-conscious
driving
zHigh noise levels and exhaust emissions
are often a result of driving without due
attention to saving energy and
protecting the environment.
zYou should therefore drive with energy in
mind: "more kilometres – less fuel".
Reduce the noise level and exhaust
emissions by adopting an environment-
conscious driving style. This is extremely
worthwhile and improves the quality of
life.
Fuel consumption depends to a great
extent on your own personal driving
style. The following hints are intended to
help you consume fuel at a rate that is as
close as possible to the specified levels
3186.
Check your vehicle’s fuel consumption
every time you refuel. This facilitates
early detection of any irregularities
causing increased fuel consumption. Warming up
zFull throttle and warming up at idle
speed increase wear, fuel consumption,
exhaust emission, the amount of
pollutant in the exhaust and the amount
of noise.
zDrive off immediately after starting.
Warm up the engine by running it at
moderate engine speeds.
Uniform speed
zHectic driving significantly increases fuel
consumption, the exhaust emissions, the
proportion of pollutant in the exhaust
gas and the noise level.
zDo not accelerate and brake
unnecessarily. Drive at uniform speed,
watching the road.
Avoid frequent starting off and stopping
e.g. at traffic lights, in short distance
traffic and in queues of traffic by means
of clever planning. Select roads with
good traffic flow.
Idling
zThe engine also consumes fuel when
idling.
zIf you have to wait for more than one
minute, it is worthwhile switching off the
engine. Five minutes of idling
corresponds to approximately one
kilometre of driving.

109
Driving and operation
Overrun
zThe fuel supply is automatically shut off
during overrun, e.g. when the vehicle is
being driven down long gradients or
when braking 3107.
zTo enable the overrun cut-off to come
into action and save fuel, do not
accelerate or declutch during overrun.
Correct gear selection
zHigh revs increase engine wear and fuel
consumption.
zDo not race your engine. Avoid driving at
high engine speeds.
Making use of the tachometer helps to
save fuel. Drive in a low engine speed
range for each gear as much as possible
with uniform engine speeds. Drive as
often as possible in top gear, select the
next higher gear as soon as possible,
and only change down when the engine
is no longer running perfectly smoothly.
High speed
zThe higher the speed, the higher the
consumption and the noise level. At top
speed, you consume a great deal of fuel
and produce excessive noise and
exhaust emissions. zSlightly releasing the accelerator pedal
results in distinct fuel savings with no
major loss of speed.
Drive at no more than around three
quarters of maximum speed and you will
use up to 50 % less fuel, without losing a
great deal of time.
Tyre pressure
zInadequate tyre pressure, leading to
higher road resistance, costs money in
two ways: for more fuel and increased
tyre wear.
zRegular checks (every 14 days) pay off.
Electrical loads
zThe power consumption of electrical
equipment increases fuel consumption.
zSwitch off all auxiliary electrical loads
(e.g. air conditioning3, heated rear
window) when not needed.
Roof racks
zDue to air resistance, a roof load can
increase fuel consumption by approx.
1 l/100 km.
zRemove them if they are not being used. Repair and maintenance
zImproper repairs or adjustment and
maintenance work can increase fuel
consumption. Do not carry out work on
the engine yourself.
You may out of ignorance infringe
environmental laws by not disposing of
materials properly.
Appropriate parts might not be recycled.
Contact with some of the materials
involved may pose a health hazard.
zWe recommend that repair and
maintenance be entrusted to your Opel
Partner.
Extreme driving conditions
zGoing up steep slopes, cornering, driving
on poor roads and winter driving all
increase fuel consumption.
Fuel consumption increases dramatically
in urban traffic and at winter
temperatures, especially on short trips
when the engine operating temperature
is not reached.
zFollowing the instructions given above
will minimise consumption under these
conditions.

118 Driving and operationMaintenance
Have all maintenance work carried out at
the specified intervals. We recommend
that you entrust this work to your Opel
Partner, who has proper equipment and
trained personnel available. Electronic
testing systems permit rapid diagnosis and
remedy of faults. This way you can be
certain that all components of the vehicle’s
electrical, injection and ignition systems
operate correctly, that your vehicle has a
low level of pollutant emission and that the
catalytic converter system will have a long
service life.
You are thereby making an important
contribution towards keeping the air clean
and compliance with emissions legislation.
Checking and adjustment of the fuel-
injection and ignition systems is part of the
scope of inspection. For this reason you
should have all maintenance work carried
out at the intervals specified in your Service
and Warranty Booklet.
Picture no: 11629s.tif
Hydraulic brake system The foot brake comprises two independent
brake circuits.
If a brake circuit fails, the vehicle can still be
braked using the other brake circuit.
However, the brake pedal must be
depressed a considerable way before any
braking effect occurs, and much more
force is required. The braking distance is
longer. Contact a workshop for assistance
before continuing to drive. To ensure the full pedal travel can be
utilised, especially in case of a fault in one
of the brake circuits, there must be no mats
in the vicinity of the pedals 3107.
When the engine is not running, the
support of the brake servo unit disappears
once the brake pedal has been depressed
once or twice. Braking effect is not
reduced, but braking requires significantly
greater force. This is especially important
to bear in mind when towing.
The brake fluid level should be checked
regularly. If the brake fluid level is too low
and the hand brake is not applied, control
indicator R on the instrument panel lights
up 369.

119
Driving and operation
Picture no: 12482s.tif
Brake system control indicator R
The control indicator illuminates when the
ignition is switched on if the hand brake is
applied or if the brake or clutch fluid level is
too low. Brake fluid 3179. For vehicles with manual transmission
automated 3, the control indicator flashes
for a few seconds when the ignition is
turned off if the hand brake is not applied.
Anti-lock Braking System
(ABS
u)3
ABS prevents the wheels from locking.
ABS starts to regulate brake pressure as
soon as a wheel shows a tendency to lock.
The vehicle remains steerable, even during
hard braking.
ABS control is made apparent though a
pulse in the brake pedal and the noise of
the regulation process.
For optimum braking, keep the brake
pedal fully depressed throughout the
braking process, despite the fact that the
pedal is pulsating. Do not reduce the
pressure on the pedal.
Picture no: 12147s.tif
Control indicator u for ABS
It illuminates for a few seconds when
ignition is switched on. Once the control
indicator goes out, the system is ready for
operation.
If the control indicator does not go out
after a few seconds, or if it illuminates while
driving, there is a fault in the ABS. The
brake system remains operational without
ABS regulation.
9 Warning
If the control indicator illuminates when
the handbrake is released, stop driving
immediately. Contact a workshop for
assistance.

124 Driving and operationTyre designations
Meanings:
e.g. 175/70 R 14 79 T
Speed code letters: Winter tyres 3
Instructions on fitting new tyres 3121.
Limitations 3191.
Winter tyres improve driving safety at
temperatures below 7 C.
The design of summer tyres means they
have limited qualities for winter driving.
In accordance with country-specific
regulations, affix the speed sticker 3 in the
driver’s field of view.
Use of a spare wheel fitted with a summer
tyre may affect the vehicle’s driveability,
especially on slippery road surfaces.
Obtain a replacement for the faulty tyre as
soon as possible, and have the wheel
balanced and fitted to the vehicle.
Wheel trims 3
The use of wheel trims and tyres that Opel
has approved for the vehicle and therefore
fulfill all requirements for the relevant
combination of wheels and tyres.
If the wheel trims and tyres used are not
Opel-approved, the tyres must not have a
beaded edge. Wheel trims must not impair brake cooling.
Remove the wheel trims if fitting tyre
chains3.
175= Tyre width in mm
70= Cross-section ratio (tyre height to
tyre width in %)
R= Belt type Radial
14= Rim diameter in inches
79= Load index e. g.: 79 corresponds
to 437 kg
T= Speed code letter
Q= up to 160 km/h
S= up to 180 km/h
T= up to 190 km/h
H= up to 210 km/h
V= up to 240 km/h
W= up to 270 km/h
9 Warning
Use of unsuitable tyres or wheel trims
could lead to sudden loss of air and
thereby accidents.

126 Driving and operationTowing equipment
3
Only use towing equipment that has been
approved for your vehicle. Entrust
retrofitting of towing equipment to a
workshop. It may be necessary to make
changes that affect the cooling system,
heat shields or other equipment.
Installation dimensions of towing
equipment 3197.
Towing equipment with fixed coupling
ball bar3
In the case of trailers/caravans with brake,
attach break-away stopping cable to eye
to right of coupling ball bar. Caravan/trailer towingCaravan and trailer loads
1)
The permissible caravan/trailer loads are
vehicle and engine-dependent maximum
values which must not be exceeded. The
actual caravan/trailer load is the difference
between the actual gross weight of the
caravan/trailer and the actual coupling
socket load with the caravan/trailer
coupled.
The permissible caravan/trailer loads are
specified in the vehicle documents. In
general, they are valid for gradients up to
max. 12 %. The permitted caravan/trailer load applies
up to the specified incline and up to an
altitude of 1000 metres above sea level.
Since engine power decreases as altitude
increases because of the air becoming
thinner, therefore reducing climbing ability,
the permitted towing weight also
decreases by 10 % for every 1000 metres
of additional altitude. The towing weight
does not have to be reduced when driving
on roads with slight inclines (less than 8 %,
e. g. motorways).
The permissible gross train weight must not
be exceeded. This weight is specified on
the identification plate 3182. Coupling socket load
The coupling socket load is the load
exerted by the trailer/caravan on the
coupling ball. It can be varied by changing
the weight distribution when loading the
trailer/caravan.
The maximum permissible coupling socket
load (50 kg) is specified on the towing
equipment identification plate and in the
vehicle documents. Always aim for the
maximum load, especially in the case of
heavy caravans/trailers. The coupling
socket load should never fall below 25 kg.
When measuring the coupling socket load,
make sure that the drawbar of the loaded
trailer/caravan is at the same height as it
will be when the trailer/caravan is coupled
with the towing vehicle loaded. Particularly
important for trailers/caravans with
tandem axle.
Rear axle load during towing
The permissible axle loads must not be
exceeded. 1)Observe national regulations.

136 Self-help, vehicle careInformation on directional tyres 3
Fit directional tyres such that they roll in the
direction of travel. The rolling direction is
indicated by a symbol (e.g. an arrow) on
the sidewall.
The following applies to tyres fitted
opposing the rolling direction:
zDriving conditions may be altered. Have
the defective tyre replaced as soon as
possible.
zDo not drive faster than 80 km/h.
zDrive especially carefully in wet and
snowy weather.
Further information on directional tyres
3121.
Picture no: 2457s.tif
Jack
£
3 and vehicle tools
3
The jack and the vehicle tools have been
specially developed for your vehicle and
must only be used on that vehicle. Only use
jack for changing wheels.
Combo
The jack and the vehicle tools are located
in a stowage compartment in the side
panel trim on the right-hand side.
Release the flap by pressing the retaining
lugs. See Figure.
Picture no: 12458s.tif
The jack is secured in place by a wing
screw. The vehicle tools are secured to the
jack 3 with rubber bands.

146 Self-help, vehicle care
Picture no: 11651s.tif
Before replacing a fuse, turn off the
respective switch and the ignition.
Slot fuse-gripping tool onto fuse and
withdraw it.
Picture no: 12892j.tif
A defective fuse can be recognized by its
melted wire. A new fuse should only be
installed after the cause of the trouble has
been rectified. Always use fuses with the correct current
value. This is shown on each fuse, and is
also indicated by the fuse colour and the
plug-in location in the fuse box.
Different versions of fuses are used.

174 Opel Service, maintenanceGenuine Opel Parts and
Accessories We recommend that you use "Genuine
Opel Parts and Accessories" and
conversion parts approved expressly for
your vehicle type. These parts have
undergone special tests to establish their
reliability, safety and specific suitability for
Opel vehicles. Despite continuous market
monitoring, we cannot assess or guarantee
these attributes for other products, even if
they have been granted approval by the
relevant authorities or in some other form.
"Genuine Opel Parts and Accessories" and
conversion parts approved by Opel can be
obtained from your Opel Partner, who can
provide comprehensive advice on
permitted technical changes and ensure
correct installation.
Picture no: 17922s.tif
Performing work To avoid injury from moving parts and
cables conducting ignition voltage, only
carry out engine compartment checks
(e. g. checking brake fluid or engine oil
level) when the ignition is switched off.
Picture no: 11671s.tif
To aid identification, the caps used when
topping up engine oil, coolant and washer
fluid as well as the oil dipstick are coloured
yellow.
9 Warning
Only perform engine compartment
checks when the ignition is off.
The cooling fan may start operating
even if the ignition is off.
9 Warning
The ignition system 3 and Xenon
headlamps 3 use extremely high
voltage. Do not touch.

190 Technical dataWeights
(kg)
, Table 1, kerb weight
1)
1)According to EC Directive 70/156/EC, including assumed weights for driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Combo van EngineManual transmission Manual transmission automated
without/with air
conditioning
[kg]Z 14 XEP 1190/1350 –
Z 16 YNG 1322/1352 –
Z 13 DTJ 1285/1420 1285/1420
Z 17 DTH 1320/1455 –Weights
(kg)
, Table 1, kerb weight
Combo EngineManual transmission manual transmission automated
without/with air
conditioning
[kg]Z 14 XEP 1235/1265 –
Z 16 YNG 1367/1397 –
Z 13 DTJ 1325/1355 1325/1355
Z 17 DTH 1365/1395 –Weights
, Table 2, heavy accessories
Accessories Folding
sun roofTowing
equipmentAnti-lock braking
system (ABS)Sliding door (front
passenger’s side) Rear vent
windowsLoad
compartment grilleSplit load
compartment grille
Weight [kg] 18 18 7 23 9 8 10