instrument panel OPEL FRONTERA 1998 Owner's Guide
[x] Cancel search | Manufacturer: OPEL, Model Year: 1998, Model line: FRONTERA, Model: OPEL FRONTERA 1998Pages: 6000, PDF Size: 97 MB
Page 2578 of 6000
WIPER/WASHER SYSTEM8B–9
Alarm & Relay Control Unit
Removal
1. Disconnect the battery ground cable.
2. Remove the glove box.
3. Remove the instrument panel passenger lower cover
assembly.
4. Remove the passenger Knee bolster reinforcement
assembly.
5. Remove the fixing bolts, disconnect the connectors
and then remove the alarm & relay control unit (1).
826RW020
Installation
To install, follow the removal steps in the reverse order.
Rear Washer Motor
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim pad(2).
3. Remove two screws, disconnect the connector,
remove the washer hose and then remove the rear
washer tank(3).
4. Pull out the rear washer motor(1) from the washer
tank.
885RS009
Installation
To install, follow the removal steps in the reverse order.
Page 2581 of 6000
8B–12WIPER/WASHER SYSTEM
Headlight Wiper and Washer Switch
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly(1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly(2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover(3).
Refer to the Instrument Panel Assembly in Body
Structure section.
821RW024
5. Remove the instrument panel cluster assembly(4).
Refer to the Instrument Panel Assembly in Body
Structure section.
6. Disconnect the connector and push the lock from the
back side of the instrument panel cluster assembly to
remove the headlight wiper switch(5).
825RW245
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. Push the switch with your fingers until it locks
securely.
Page 2585 of 6000
8C–2ENTERTAINMENT
Cigarette Lighter
General Description
When the cigarette lighter is pushed in with the starter
s w i t c h a t e i t h e r “ A C C ” o r “ O N ” p o s i t i o n , a c i r c u i t i s f o r m e d
in the cigarette lighter case to heat the lighter coil.
The cigarette lighter is sprung back to its original position
after the lighter coil is heated.
Removal
1. Disconnect the battery ground cable.
2. Remove the lower cluster assembly(1).
Refer to the Instrument Panel Assembly removal
steps in Body Structure section.
3. Disconnect the connectors, remove the socket of the
illumination light, the retaining ring(7), the outer
case(6), the cigarette lighter(3) and socket(4), the
bezel(5) and then remove the cigarette lighter
assembly(2).
826RS007
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. When installing the bezel, align the projected portion
of the socket with the notch of the bezel.
Page 2586 of 6000
ENTERTAINMENT8C–3
Digital Clock
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly(1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly(2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover
assembly(3).
Refer to the Instrument Panel Assembly in Body
Structure section.
821RW024
5. Remove the instrument panel cluster assembly(4).
Refer to the Instrument Panel Assembly in Body
Structure section.
6. Disconnect the connector and push the lock from the
back side of the instrument panel cluster assembly to
remove the digital clock(5).
821RW034
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Push in the switch with your fingers until it locks
securely.
Page 2590 of 6000
ENTERTAINMENT8C–7
Radio
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly (1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly (2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover
assembly (3).
Refer to the Instrument Panel Assembly in Body
Structure section.
821RW024
5. Remove the instrument panel cluster assembly(4).
Refer to the Instrument Panel Assembly in Body
Structure section.
6. Remove two screws and disconnect the radio
connector(5) and antenna feeder plug(6) to remove
the radio(7).
825RW039
Installation
To install, follow the removal steps in the reverse order.
Page 3119 of 6000
D08RW844
4I-12 8
5H-9
3.0
B/Y
0.5
L/W
0.5
L/W
0.85 L/W 0.5
R/W 0.3
R/G
0.85
L/W 0.5
L/W
0.85 G/R
0.5
R/W
C-4 10A
ELEC.IGN.
4WD SW
(INSTRUMENT
PANEL)
4WD CONTROL UNIT
STARTER SW (IG1)
20
H-25 14H-16
7
H-12
6I-12
17
C-94
TAIL RELAY (4)
ILLUMINATION
CONTROLLER(3)
3I-12 2
I-12
C-94
E-30
1.0
B/L 0.5
B/L
1.25 B/L
COMMON
CHAMBER
16C-94
INDICATOR/
WARNING LIGHT
(METER)
3.0
B/Y
C-10 10A
METER,GAUGE
STARTER SW
(IG1)
19C-94 19
H-27
0.5
L/Y 0.5
L/Y
0.5 LG
0.5 LG 18
H-7
0.5 LG 0.85
W/G
AC GENERATOR (L)
18
I-9 15
I-9
6I-9
4WD
CHARGE
H-26 6
0.85
W/G
CHARGE RELAY (1) 6I-9
CHARGE
14H-5
7
C-16
0.5
B
FENDER-LH
16 (4JG2) (4JG2)C-94
Page 3122 of 6000
D08RW844
4I-12 8
5H-9
3.0
B/Y
0.5
L/W
0.5
L/W
0.85 L/W 0.5
R/W 0.3
R/G
0.85
L/W 0.5
L/W
0.85 G/R
0.5
R/W
C-4 10A
ELEC.IGN.
4WD SW
(INSTRUMENT
PANEL)
4WD CONTROL UNIT
STARTER SW (IG1)
20
H-25 14H-16
7
H-12
6I-12
17
C-94
TAIL RELAY (4)
ILLUMINATION
CONTROLLER(3)
3I-12 2
I-12
C-94
E-30
1.0
B/L 0.5
B/L
1.25 B/L
COMMON
CHAMBER
16C-94
INDICATOR/
WARNING LIGHT
(METER)
3.0
B/Y
C-10 10A
METER,GAUGE
STARTER SW
(IG1)
19C-94 19
H-27
0.5
L/Y 0.5
L/Y
0.5 LG
0.5 LG 18
H-7
0.5 LG 0.85
W/G
AC GENERATOR (L)
18
I-9 15
I-9
6I-9
4WD
CHARGE
H-26 6
0.85
W/G
CHARGE RELAY (1) 6I-9
CHARGE
14H-5
7
C-16
0.5
B
FENDER-LH
16 (4JG2) (4JG2)C-94
Page 3125 of 6000
D08RW845
0.85
W/G
CHARGE RELAY (1) 6I-9
CHARGE
(4JG2)
4I-12
8
4H-24
3.0
B/Y
0.5
L/W
0.5
L/W
0.85 L/W 0.5
R/W 0.3
R/G
0.85
L/W 0.5
L/W
0.85 G/R
0.5
R/W
C-4 10A
ELEC.IGN.
4WD SW
(INSTRUMENT
PANEL)
4WD CONTROL UNIT
STARTER SW (IG1)
5
H-25 6H-16
10
H-8
6I-12
17
C-94
TAIL RELAY (4)
ILLUMINATION
CONTROLLER(3)
3I-12 2
I-12
C-94
E-30
1.0
B/L 0.5
B/L
1.25 B/L
COMMON
CHAMBER
16C-94
INDICATOR/
WARNING LIGHT
(METER)
3.0
B/Y
C-10 10A
METER,GAUGE
STARTER SW
(IG1)
19C-94 21
H-25
0.5
L/Y 0.5
L/Y
0.5 LG
0.5 LG 18
H-7
0.5 LG 0.85
W/G
AC GENERATOR (L)
18
I-9 15
I-9
6I-9
4WD
CHARGE
H-25 10
14H-5
8
C-16
0.5
B
FENDER-LH
16 (4JG2)C-94
Page 3128 of 6000
D08RW845
0.85
W/G
CHARGE RELAY (1) 6I-9
CHARGE
(4JG2)
4I-12
8
4H-24
3.0
B/Y
0.5
L/W
0.5
L/W
0.85 L/W 0.5
R/W 0.3
R/G
0.85
L/W 0.5
L/W
0.85 G/R
0.5
R/W
C-4 10A
ELEC.IGN.
4WD SW
(INSTRUMENT
PANEL)
4WD CONTROL UNIT
STARTER SW (IG1)
5
H-25 6H-16
10
H-8
6I-12
17
C-94
TAIL RELAY (4)
ILLUMINATION
CONTROLLER(3)
3I-12 2
I-12
C-94
E-30
1.0
B/L 0.5
B/L
1.25 B/L
COMMON
CHAMBER
16C-94
INDICATOR/
WARNING LIGHT
(METER)
3.0
B/Y
C-10 10A
METER,GAUGE
STARTER SW
(IG1)
19C-94 21
H-25
0.5
L/Y 0.5
L/Y
0.5 LG
0.5 LG 18
H-7
0.5 LG 0.85
W/G
AC GENERATOR (L)
18
I-9 15
I-9
6I-9
4WD
CHARGE
H-25 10
14H-5
8
C-16
0.5
B
FENDER-LH
16 (4JG2)C-94
Page 3191 of 6000
8E–14METER AND GAUGE
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly(1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly(2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover(3).
Refer to the Instrument Panel Assembly in Body
Structure section.
740RS004
5. Remove four fixing screws and disconnect the meter
connectors to remove the meter assembly(5).
825RW031
CAUTION: The removed meter assembly should be
placed upright or with its face side up.
Installation
To install, follow the removal steps in the reverse order.
Warning Light Bulb, Indicator Light Bulb, Illumination Light Bulb,
A/T Indicator Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the meter assembly(1).
Refer to the Meter Assembly removal steps in this
section.
3. Hold the bulb socket by hand and rotate it
counterclockwise to remove the socket & bulb(2)
from the meter body.
825RW032
Installation
To install, follow the removal steps in the reverse order.