battery OPEL FRONTERA 1998 Workshop Manual

7A–44
AUTOMATIC TRANSMISSION (4L30–E)
Speed Sensor (Extension Housing)
Removal
1. Disconnect battery ground cable.
2. Remove front console.
3. Remove selector lever assembly.
4. Disconnect speed sensor harness connector from
speed sensor.
5. Remove one 10 mm screw and speed sensor with
O–ring.
241RW007
Installation
1. Inspect the speed sensor O–ring, and replace it if
necessary.
2. Install speed sensor assembly and 10 mm screw.
To r q u e : 9 N
m (0.9 kgꞏm/78 lb in)
3. Connect speed sensor harness connector to speed
sensor.
4. Install selector lever assembly.
Adjust shift lock cable. Refer to Selector Lever in
this section.
5. Install front console.
6. Connect battery ground cable.
Transmission Oil Temperature Sensor (Adapter Case)
Removal
1. Raise the vehicle and support it on jack stands.
2. Disconnect battery ground cable.
3. Drain fluid.
4. Remove transfer and exhaust protectors.
5. Remove exhaust pipe and disconnect oxygen sensor
connector.
6. Remove twelve 10 mm adapter case oil pan fixing
screws, adapter case oil pan, and gasket.
NOTE: Oil pan still contains transmission fluid. Place a
large drain container under the oil pan, and drain the fluid
carefully.
7. Disconnect wiring harness from force motor solenoid,
converter clutch solenoid, and 5 pin connector of
adapter case. Pull only on connectors, not on wiring
harness.
8. Disconnect ground wire from converter clutch
solenoid wiring harness connector.9. Remove wiring harness assembly (transmission oil
temperature sensor).
243RW002

7A–45 AUTOMATIC TRANSMISSION (4L30–E)
Installation
1. Connect ground wire to converter clutch solenoid
wiring harness connector of the wiring harness
assembly.
2. Install wiring harness assembly to converter clutch
solenoid, force motor, and 5 pin connector of adapter
case.
3. Install oil pan gasket, oil pan, and twelve 10 mm fixing
screws. Tighten the screws to the specified torque.
Torque: 11 N
m (1.1 kgꞏm/96 lb in)4. Install exhaust pipe and connect oxygen sensor
connector. Tighten the bolts to the specified torque.
Exhaust pipe flange bolt torque:
43 N
m(4.4kgꞏm/32lbft)
5. Install transfer and exhaust protectors. Tighten the
bolts to the specified torque.
To r q u e : 3 7 N
m (3.8 kgꞏm/27 lb ft)
6. Fill transmission through the overfill screw hole of oil
pan, using ATF DEXRON
–III.
Refer to Changing Transmission Fluid in this section.
7. Connect battery ground cable.
Front Oil Seal (Converter Housing)
Removal
1. Remove transmission assembly with transfer case
from the vehicle. Refer to Transmission (with Transfer
Case) in this section.
2. Remove torque converter from converter housing.
3. Remove three screws and oil seal ring from converter
housing.
241RW008
Installation
1. Apply clean ATF to the new oil seal ring lip.
Install oil seal ring to converter housing. Tighten the
screws to the specified torque.
To r q u e : 3 N
m (0.3 kgꞏm/26 lb in)
2. Install torque converter to converter housing.
3. Install transmission assembly with transfer case to
the vehicle. Refer to Transmission (with Transfer
Case) in this section.

7A–72 AUTOMATIC TRANSMISSION (AW30-40LE)
TCM STANDARD VOLTAGE
Check circuitTe r m i n a l
Measuring condition Voltage (V)
+-
Throttle position sensorC79-6 C79-28Throttle fully opened (WOT) 3.47
4.56
Throttle fully closed (idling) 0.25
0.45
C79-19 C79-18 Key switch ON 4.75
5.25
Output revolution sensor C79-4 C79-16 Engine idling in gear 0
3
Input revolution sensor C79-5 C79-17 Engine idling 0
3
Speed meter sensor C79-7C78-15
or -19Vehicle speed 10
20 km/h Less than 1.4
about 5
Brake switch C78-18C78-15
or -19Depress brake 7
16
Release brake Less than 1
O/D OFF switch C79-3C78-15
or -19O/D OFF switch ON (O/D OFF) 7
16
O/D OFF switch OFF (O/D ON) Less than 1
Neutral start switch
C79-2C78-15
or -19Selector “P” range 7
16
(P) Selector all ranges except “P” Less than 1
Neutral start switch
C79-1C78-15
or -19Selector “R” range 7
16
(R) Selector all ranges except “R” Less than 1
Neutral start switch
C79-9C78-15
or -19Selector “N” range 7
16
(N) Selector all ranges except “N” Less than 1
Neutral start switch
C79-8C78-15
or -19Selector “D” range 7
16
(D) Selector all ranges except “D” Less than 1
Neutral start switch
C79-21C78-15
or -19Selector “2” range 7
16
(2) Selector all ranges except “2” Less than 1
Neutral start switch
C79-20C78-15
or -19Selector “L” range 7
16
(L) Selector all ranges except “L” Less than 1
Engine revolution signal C79-15C78-15
or -19Engine idling Less than 1.4
9 16
Diagnosis terminal C79-24C78-15
or -19Self-diagnosis ON
0
1.5
Power pattern switch C79-23C78-15
or -19Power pattern switch OFF (NORMAL) 8
16
Power pattern switch ON (POWER) Less than 1.4
Winter select switch C79-13C78-15
or -19Switch OFF 8
16
Switch ON Less than 1.4
Electrical source (Battery) C78-13C78-15
or -19—
9
16
Electrical source (Ignition) C78-20C78-15
or -19Key switch ON
9
16
Oil temperature warning lamp C79-11C78-15
or -19Oil temperature warning lamp ON Less than 1
Oil temperature warning lamp OFF 8
16
“CHECK TRANS lamp” C79-10C78-15
or -19“CHECK TRANS” lamp ON Less than 1
“CHECK TRANS” lamp OFF 8
16
Power lamp C79-22C78-15
or -19Power lamp ON Less than 1
Powe r l a m p O F F 8
16

7A–76 AUTOMATIC TRANSMISSION (AW30-40LE)
249RY00010
249RY00008
NEUTRAL START SWITCH INSPECTION
Inspection
With a circuit tester, make a continuity test on the neutral star t
switch with the moving piece set in each position.
Continuity
Removal
Preparation:
Disconnect negative (–) battery cable.
1. Remove rear sound cover.
2. Remove the rear side ATF cooler pipe from the
transmission elbow.
3. Disconnect neutral star t switch connector.
4. Unstake the lock washer, and then remove the shaft nut.
5. Remove the neutral start switch.
Installation
To install, follow the removal steps in the reverse order, noting
the following points;
Adjustment
1) Loosen the neutral star t switch bolt and set the shift
selector to the "N" range.
2) Align the groove and neutral basic line.
3) Hold in position and tighten the bolt.Te r m i n a l
Po s i ti on143526879
P
R
N
D
2
L
Torque Nꞏm (kgꞏcm/lbꞏin)
Nut 7 (70/61)
Bolt 13 (130/113)

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–77
310RW020
F07RY00017
F07RY00018
BRAKE SIGNAL INSPECTION
Check that the brake light comes on when the brake pedal is
depressed.
VEHICLE SPEED SENSOR INSPECTION
1. Connect the Vehicle speed sensor connector terminal (1) to
the battery ( +) terminal and terminal (2) to the battery (-)
terminal.
2. Connect a resistance of 1.3k ohm to 5k ohm (1.4W or
more) between terminals (1) and (3).
NOTE:
Be extremely careful not to connect the battery (+) terminal
to the terminal (3)
This may damage the vehicle speed sensor.
3. Rotate the shaft of the vehicle speed sensor slowly and
measure the voltage at both ends with a digital tester.
Replace the sensor when the result of inspection is found
abnormal.
INPUT AND OUTPUT REVOLUTION
SENSOR INSPECTION
Use an ohmmeter to measure the resistance between
terminals 1 and 2.The voltage, with one rotation of shaft, fluctuates four
times in the following range: 10 to 14V
2V or less.
Standard resistance 560 – 680
(20C)
610 – 740
(40C)

7A–78 AUTOMATIC TRANSMISSION (AW30-40LE)
F07RY00019
225RY00001
220RY00001
244RX00001
PATTERN SELECT SWITCH INSPECTION
Inspect that there is continuity between each terminals.
OVERDRIVE OFF SWITCH INSPECTION
Inspect that there is continuity between terminals 2 and 4.
SOLENOID INSPECTION
1. Resistance check
• Using an ohmmeter, check the resistance between each
terminals (S1/S2/SL) and body.
• Using an ohmmeter, check the resistance between
terminals (STH) and (STHG).

NOTE:
If the pressure contorl solenoid resistance is not within
specification, replace the valve body assembly.
2. Operation Check
Check the solenoid operation by blowing into an oil hole as
shown in the figure.
Solenoid S1 and S2 (Normal close type)
Solenoid S1, S2 and Lock-up
solenoid resistance11 - 15(20C)
12 - 16
(40C)
Pressure control solenoid
resistance5 - 5.6
(20C)
5.4 - 6.1
(40C)
When battery terminal is
disconnectedNo air leaks
When battery terminal is
connectedAir passes through

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–79
244RY00005
101RY00004
249RW003
242RW013
Look-up solenoid (Normal open type)
THROTTLE POSITION SENSOR
INSPECTION
1. Turn the starter switch to the "ON" position.
2. Measure the voltage between throttle position sensor
connector terminals 2 (output) and 3 (ground).
NOTE:
• Do not remove the sensor connector.
• Make sure that power source (4.75-5.25V) is measured
between terminals 1 and 3 before measurement at step
2).
ATF TEMPERATURE SENSOR
INSPECTION
1. Disconnect the front side ATF cooler pipe from the elbow
and remove the elbow.
2. Remove the ATF temperature sensor from the transmission
case.
3. Place the ATF temperature sensor in a container of ATF.
4. Measure the resistance between each terminals.
5. If either of the measured values exceeds the specified,
replace the ATF temperature sensor.
Nꞏm (kgꞏm/ lbꞏft)
When battery terminal is
disconnectedAir passes through
When battery terminal is
connectedNo air leaks
Throttle position Voltage (V)
Idle 0.25-0.45
WOT 3.74-4.56
Resistance 0.5 - 30 k
(0C - 120C)
Torque 15 (1.5/11)

7A–80 AUTOMATIC TRANSMISSION (AW30-40LE)
256RY00001
256RW012
256RW013
SELECTOR LEVER
INSPECTION
1. Make sure that when the selector lever is shifted from "P" to
"L", a "clicking" can be felt at each shift position. Make sure
that the gear corresponds to that of the position plate
indicator.
2. Check to see if the shifter lever can be shifted as shown.
REMOVAL
Preparation:
Diconnect negative (–) battery cable.
1. Transfer Control Lever Knob
2. Front Console
Disconnect wiring harness connectors.
3. Selector Lever Assembly
1) Disconnect shift lock cable from the selector lever
assembly side.
2) Disconnect wiring harness connectors.
3) Disconnect shift control rod from the selector lever
assembly side.

AUTOMATIC TRANSMISSION (AW30-40LE) 7A–83
826RY00005
826RY00006
249RY00011
249RY00012
TRANSMISSION CONTROL MODULE
(TCM)
REMOVAL
Preparation:
Disconnect negative (–) battery cable.
1. Disconnect the TCM harness connectors.
2. Remove fixing nuts (3 pieces) and TCM from the bracket.
INSTALLATION
To install, follow the removal steps in reverse order.
SHIFT SOLENOID AND LOCK-UP
SOLENOID
REMOVAL
Preparation:
• Disconnect negative (–) battery cable.
• Remove the rear sound cover.
• Drain the fluid.
Refer to
"ATF REPLACEMENT" in this section.
1. Remove the nineteen bolts and oil pan.
2. Remove the oil strainer assembly.
3. Disconnect the solenoid wiring connectors from the shift
solenoid S1(1), S2(2) and lock-up solenoid (3).
4. Remove each retaining bolts and solenoids.
INSTALLATION
To install, follow the removal steps in reverse order noting the
following point;
Tprque Nꞏm (kgꞏcm/lbꞏin)
Solenoid S1, S2 bolt 7 (70/61)
Lock-up solenoid bolt 10 (100/87)

7A–84 AUTOMATIC TRANSMISSION (AW30-40LE)
VALVE BODY ASSEMBLY AND PRESSERE CONTOROL SOLENOID
244RY00009
244RY00003
REMOVAL
Preparation:
• Disconnect negative (–) battery cable.
• Remove the rear sound cover.
• Drain the fluid.
Refer to
"ATF REPLACEMENT" in this section.
1. Remove the nineteen bolts and oil pan.
2. Remove the oil strainer assembly.
3. Disconnect the soleniod wiring connectors from the
solenoids.
4. Remove the twenty botls from the valve body.
5. Remove the valve body assembly and pressure
control solenoid.
• When removing valve body assembly from the
transmission case, loosen the solenoid clamp bolt
and remove the pressure control solenoid from
the upper valve body assembly.
Also disconnect the harness connector from the
pressure control solenoid.