wheel OPEL MERIVA 2009 Owner's Manual

92 Instruments, Controls
Picture no: 17914s.tif
Triple information display Set date and time
The infotainment system 3 must be off.
Activate setting mode by holding the Ö
button depressed for about 2 seconds. The
flashing value is adjusted using the ;
button. The Ö button is used to switch to
the next unit and to exit setting mode. Automatic time synchronisation
3
The RDS signal of most VHF transmitters
automatically sets the time. This can be
identified by } in the display.
Some transmitters do not send a correct
time signal. In such cases, we recommend
that you switch off automatic time
synchronisation.
Activate setting mode and set it to year
setting. Hold the Ö button depressed
about 3 seconds until } flashes in the
display and “RDS TIME" appears. The
function is activated (RDS TIME 1) or
deactivated (RDS TIME 0) with the ;
button. Exit setting mode using the Ö
button.
Picture no: 16711t.tif
Graphical information display
3
or colour information display
3,
selecting functions
Functions and their menus are depicted in
the graphical information display and
colour information display.
These functions are marked or executed in
the menu display via the cross switch, the
multifunction knob 3 on the Infotainment
System or buttons 3 on the steering wheel.
8:56
5
,5
°C
07.04.2004
FM AS [TP] REG CDinMP3

90.6
MHz
19,5° 19:36

93
Instruments, Controls
Picture no: 15593t.tif
To select with four-way button
Select menu items via menus and with the
buttons/four-way button of the
Infotainment system.
Picture no: 15559t.tif
Selection with the multifunction knob 3
Turn the multifunction button to highlight
menu items or commands and to select
function areas.
Press the multifunction button to select the
highlighted item or confirm a command.
To exit a menu, turn the multifunction
button left or right to Return or Main and
select.
Picture no: 14034s.tif
Selection using buttons 3 on steering
wheel
Select menu options via menus and with
the buttons.

97
Instruments, Controls
Picture no: 16719t.tif
Graphical information display
3
or Colour information display 3,
Trip computer
3
The trip computers provide information on
driving data, which is continually recorded
and evaluated electronically.
The trip computer main page provides
information on range, average
consumption and momentary
consumption 3.
To display the other trip computer driving
information, press BC button on
Infotainment system 3 or select trip
computer menu on display.
For vehicles with Infotainment System
CD 30 3 and steering wheel remove
control 3, the left steering wheel buttons
only operate the trip computer.
Picture no: 16710t.tif
Range
Range is calculated fr om current fuel tank
content and instantaneous consumption.
The display shows average values.
After refuelling, the vehicle updates the
range automatically after a brief delay.
Picture no: 16718t.tif
If the fuel in the tank will allow less than
50 km of travel, the message Range
appears in the display.
If the fuel in the tank will allow less than
30 km of travel, the message
Please refuel! 3 appears in the display.
Acknowledge warning message 392.
Instantaneous consumption
Display of current consumption. At low
speeds, consumption per hour is displayed.
Ü
Board Computer 19,5° 19:36
BC 1 All values
BC 2
257.0
km
Timer
Ø40
km/h
31.0
Ltr.
Ø
7.0
Ltr./100km
1
8
Range
257
km
Aver. Consump.
7.0
Ltr./100km
Inst. Consumpt.
7.6
Ltr./100km
19,5° 19:36
Range33km
OK

101
Instruments, Controls
Picture no: 14056h.tif
Windscreen washer and headlamp
washer system 3
Pull stalk towards steer ing wheel. Screen
wash is squirted onto the screen and the
wipers move back and forth a few times.
When the lights are switched on,
windscreen wash is al so squirted onto the
headlamps.
Picture no: 14057h.tif
Rear window washer and wiper system
Push stalk forwards. The rear window wiper
wipes in timed interval mode. Switch off by
pulling stalk towards the steering wheel.
If the stalk is held forwards, washer fluid is
sprayed on the rear window.

103
Lighting
Picture no: 18475s.tif
Main beam, headlamp flash Push stalk forward to switch from dipped
beam to main beam.
To switch to dipped beam, press stalk
forwards again.
To operate the headlamp flash, pull stalk
towards steering wheel. The main beam is
switched on for as long as the stalk is held
in this position.
Picture no: 14054h.tif
Turn signal lamps If the stalk is moved past the resistance
point, the turn signal lamp remains on.
When the steering wheel moves back
toward the straight-ahead position, the
turn signal lamp is automatically
deactivated.
Brief flash: press stalk to perceptible
resistance and release.
Manual disconnection of turn signal lamps
by returning to centre position.
Picture no: 14758s.tif
Fog lamps
> 3

The fog lamps can only be switched on
when both the ignition and lights are on.
Operated with the > button.
Lever upwards = Right turn signal
Lever downwards = Left turn signal

106 Lighting
Picture no: 15209j.tif
Adaptive Forward Lighting
3
(AFL) ensures better illumination of
zbends (curve lighting),
z crossings and narrow bends (cornering
light).
Curve lighting
The light beam pivots based on
steering wheel position and speed (from
approx. 10 km/h).
The headlamps shine at an angle of up
to 15 to the right or left of the direction of
travel.
Picture no:
Cornering light
An additional lamp comes on with
certain steering wheel positions (after
approx. 90), turn si gnal settings and
speeds (up to approx. 40 km/h).
The light is thrown approx. 90 to the
left or right of the car, to a distance of
approx. 30 metres.
Reversing function
If the lights are on, reverse gear is
engaged, and the turn signal is activated,
the cornering light on the appropriate side
is switched on. The cornering light stays on
for 15 seconds once the turn signal has
been switched off.
Picture no: 17887s.tif
Control indicator B for adaptive driving
lights
Illuminated: Fault in system. The system is
not ready for operation.
Contact a workshop for assistance.
After a power supply interruption the
steering angle sensor must be calibrated to
make the system operational. 3147
Control indicator
B flashes for
about 4 seconds after the ignition is
switched on as a reminder that the
headlamps have been converted, see
"Headlamps for driving abroad" 3110.

107
Lighting
Picture no: 14302s.tif
Lead-me lighting
3
Lead-me lighting when leaving the
vehicle 3
The dipped headlamps come on for
around 30 seconds after switching on and
closing the driver’s door.
To activate:
1. Switch off ignition.
2. Remove ignition key.
3. Open driver’s door.
4. Pull turn signal stalk toward steering
wheel.
5. Close driver’s door. If the driver’s door is left open, the lamps
will go out after two minutes.
The light is switched off immediately by
inserting the key into
the ignition or pulling
the turn signal stalk towards the steering
wheel again.
Picture no: 17920S.tif
Lead-me lighting when opening the
vehicle 3
The Lead-me-to-the-car lighting function
allows the dipped headlamps to be lit for
around 30 seconds using the remote
control.
This function must be activated (once):
Unlock the vehicle, put the key in the
ignition and press the light switch for
approx. 5 seconds - see next page,
Fig. 14136 S.
To deactivate the function permanently,
contact a workshop.

110 LightingBattery discharge protection
3
Some consumers such as the interior
lighting switch themselves off after
approx. 30 minutes if the ignition is off in
order to protect the battery charge. Misted light covers The inside of the light covers may mist up
briefly in poor, wet and cold weather
conditions, in heavy rain or after washing.
The mist disappears quickly by itself; to
help, switch on the lights. Headlamps when driving abroad The asymmetrical dipped beam increases
the field of vision on the passenger side of
the lane.
In countries where traffic drives on the
opposite side of the road, prevent glare as
follows.
Vehicles with halogen headlamp system
or Xenon headlamp system 3
Have headlights conver ted in a workshop.
Picture no: 14053h.tif
Vehicles with Adaptive headlight 3 (AFL)
1. Pull stalk towards steering wheel and hold.
2. Switch on ignition.
3. After approx. 3 seconds, an acoustic signal sounds and then AFL control
indicator
B flashes approx. 4 seconds.
After the switch, AFL control indicator
B
flashes for 4 seconds each time the ignition
is switched on. To return to asymmetrical dipped beam,
pull and hold the main beam stalk again,
switch on the ignition and wait for the
acoustic signal. AFL control indicator
B
will then discontinue flashing.
Control indicator
B
3 106.

111
Infotainment system
Infotainment system
Radio reception
3
Radio reception may be disrupted by
static, noise, distortion or loss of reception
due to
zchanges in dist ance from the
transmitter,
z multi-path reception due to reflection
and,
z shadowing. Infotainment system
3
The infotainment system is operated as
described in the operating instructions.
Picture no: 14034s.tif
Steering wheel remote control
3
The functions of the infotainment system 3
and the information display can be
operated with the buttons on the steering
wheel.
Further information 393 and the
infotainment system instructions.
Radio reception
3................................ 111
Infotainment system 3........................ 111
Steering wheel remote control 3........ 111
Rear seat audio system 3................... 112
AUX input 3......................................... 112
Electronic data acquisition in toll systems .............................................. 112
Mobile telephones and radio equipment 3...................................... 113

115
Climate control
Picture no: 16112s.tif
Air vents At least one air vent must be open while
cooling 3 (air conditioning compressor) is
on in order to prevent the evaporator from
icing up due to lack of air movement.
Pleasant ventilation to the head area
controlled by the position of the
temperature switch.
To increase the air supply, set the fan to a
higher speed and set the air distribution
switch to M or L.
Picture no: 14576s.tif
Centre and side (1) air vents
To open vent: rotate wheel upwards.
Adjust the direction of air flow by rotating
the horizontal and vertical wheels.
To close the vents rotate the wheel fully
downwards. Windscreen defros
ter nozzles (2)
Air distribution switch set to V or J : Air is
directed onto the windscreen and door
windows.
Additional vents
are beneath the windscreen and side
windows and in the front footwell.