battery OPEL MOVANO_B 2020 Manual user

274Vehicle careCaution
Only washer fluid with a sufficient
antifreeze concentration provides
protection at low temperatures or
a sudden drop in temperature.
Use of washer fluid containing
isopropanol can damage exterior
lamps.
Brakes
In the event of minimum thickness ofthe brake lining, a squealing noise
sounds during braking.
Continued driving is possible but
have the brake linings replaced as
soon as possible.
Once new brake linings are installed,
do not brake unnecessarily hard for
the first few journeys.
Brake fluid9 Warning
Brake fluid is poisonous and
corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces.
The brake fluid level must be between
the MIN and MAX marks.
When topping up, ensure maximum cleanliness as contamination of the
brake fluid can lead to brake system
malfunctions. Have the cause of the
loss of brake fluid remedied by a
workshop.
Only use brake fluid approved for
your vehicle.
Brake and clutch fluid 3 313.
Vehicle battery
The jump start terminal is located in
the engine compartment.
Jump starting 3 304.
The vehicle battery is maintenance-
free provided that the driving profile
allows sufficient charging of the
battery. Short-distance-driving and
frequent engine starts can discharge
the battery. Avoid the use of
unnecessary electrical consumers.
Control indicator p illuminates if
there is a fault with the charging
system. Stop, switch off engine and
seek the assistance of a workshop.
Charging system 3 99.

Vehicle care275Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Laying up the vehicle for more than
four weeks can lead to battery
discharge. Disconnect the clamp from
the negative terminal of the vehicle
battery.9 Danger
Ensure the ignition is switched off
completely (the vehicle must not
be in an Autostop) before
connecting or disconnecting the
vehicle battery.
Stop-start system 3 228.
Battery discharge protection 3 117.
Battery access
The battery is located behind a panel
in the front left-hand door step.
Remove the panel to access the
battery.
Replacing the vehicle battery Ensure that the battery is always
replaced by the same type of battery.
Seek the assistance of a workshop to
have the vehicle battery replaced.
Stop-start system 3 228.
Charging the vehicle battery9 Warning
On vehicles with stop-start
system, ensure that the charging potential does not exceed 14.6 V
when using a battery charger.
Otherwise the vehicle battery may be damaged.
9 Danger
Ensure adequate ventilation when
charging the battery. There is a
risk of explosion if gases
generated during charging are
allowed to accumulate!
Jump starting 3 304.

276Vehicle careWarning label
Meaning of symbols:● No sparks, naked flames or smoking.
● Always shield eyes. Explosive gases can cause blindness or
injury.
● Keep the vehicle battery out of reach of children.
● The vehicle battery contains sulfuric acid which could cause
blindness or serious burn
injuries.
● See the Owner's Manual for further information.
● Explosive gas may be present in the vicinity of the battery.
Additional battery
Depending on the vehicle's auxiliary
equipment, certain models may have
an additional battery mounted under
the right-hand front seat.
Note
The additional battery is
automatically connected to the main vehicle battery only when the engine
is running. It does not need to be
manually disconnected before
disconnecting the main vehicle
battery or before jump starting the vehicle.
The terminals are designed for
additional electrical consumers up to
a maximum of 50 A.
Jump starting 3 304.
Diesel fuel system bleeding If the fuel tank has been run dry, it will
be necessary to air vent or bleed the
diesel fuel system.
Fill the tank with fuel and proceed as
follows:Caution
Do not turn ignition key to position 3 before beginning the bleeding
procedure.
Ignition switch positions 3 226.
1. Turn ignition key to position 2 and
wait for a few minutes.
2. Turn key back to position 1 and
wait for 3 seconds.
3. Turn key to position 3.

Vehicle care297
7.Screw the sealant filler hose to the
tyre valve.
8. The rocker switch on the compressor must be set to
position O.
9.
Connect the red < power supply
lead on the compressor to the
jump start terminal 3 304.
Note
Depending on model, the jump start
terminal may be located at the left-
hand or right-hand side of the engine
compartment.
10. Connect the black ] power
supply lead to a vehicle grounding
point, e.g. the engine block or an
engine mounting bolt.
Note
Depending on tyre repair kit type, it
may be necessary to connect the
single power supply lead to the
power outlet or cigarette lighter
socket.
For this type, the red < and
black ] power supply leads will not
be present.
To avoid discharging the battery,
we recommend running the
engine.
11. Set the rocker switch on the compressor to position I. The tyre
is filled with sealant.
12. The compressor pressure gauge briefly indicates up to 6 bar. Then
the pressure starts to drop.
13. All of the sealant is pumped into the tyre. Then the tyre is inflated.

304Vehicle careThe following applies to tyres fitted
opposing the rolling direction:
● Driveability may be affected. Have the defective tyre renewed
or repaired as soon as possible
and fit it instead of the spare
wheel.
● Do not drive faster than 80 km/h.
● Drive particularly carefully on wet
and snow-covered road
surfaces.Jump starting
The jump start terminal is located in
the engine compartment.
A vehicle with a discharged vehicle
battery can be started using jump
leads and the vehicle battery of
another vehicle.
Do not start with a quick charger.9 Warning
Be extremely careful when starting
with jump leads. Any deviation
from the following instructions can
lead to injuries or damage caused
by battery explosion or damage to the electrical systems of both
vehicles.
9 Warning
Avoid contact of the battery with
eyes, skin, fabrics and painted
surfaces. The fluid contains
sulphuric acid which can cause
injuries and damage in the event
of direct contact.
Caution
The air suspension system must
be switched off prior to jump
starting.
Air suspension 3 231.
● Never expose the vehicle battery
to naked flames or sparks.
● A discharged vehicle battery can already freeze at a temperature
of 0 °C. Defrost the frozen vehicle
battery before connecting jump leads.
● Wear eye protection and protective clothing when
handling a vehicle battery.
● Use a booster battery with the same voltage (12 V). Its capacity(Ah) must not be much less than
that of the discharged vehicle
battery.
● Use jump leads with insulated terminals and a cross section of
at least 25 mm 2
.
● Do not disconnect the discharged
battery from the vehicle.

Vehicle care305● Switch off all unnecessaryelectrical consumers.
● Switch off the air suspension system 3 231.
● Do not lean over the vehicle battery during jump starting.
● Do not allow the terminals of one
lead to touch those of the other
lead.
● The vehicles must not come into contact with each other during
the jump starting process.
● Apply the parking brake and engage neutral (manual
transmission) or N (manual
transmission automated).Jump start terminal
In the event of a discharged vehicle
battery, the jump start terminal
enables the vehicle to be started
without the need to access the battery inside the vehicle.
The jump start terminal is located in
the engine compartment and
identified by a " <" sign on the red
insulating cover. Lift the red insulating
cover to access the terminal
connector.
Ensure the red insulating cover is
latched back into position when not in
use.
Jump starting procedure
Depending on model, the jump start
terminal may be located at the left-
hand or right-hand side of the engine
compartment.

306Vehicle care
Lead connection order:1. Connect the red lead to the positive terminal (1) of the booster
battery.
2. Connect the other end of the red lead to the jump start terminal (2)
of the vehicle with the discharged
vehicle battery.
3. Connect the black lead to the negative terminal (3) of the
booster battery.
4. Connect the other end of the black
lead to a vehicle grounding point
(4), such as the engine block or an
engine mounting bolt. Connect as
far away from the discharged
vehicle battery as possible,
however at least 60 cm.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine: 1. Start the engine of the vehicle providing the jump start.
2. After 5 minutes, start the other engine. Start attempts should be
made for no longer than
15 seconds at an interval of
1 minute.
3. Allow both engines to idle for approx. 3 minutes with the leads
connected.
4. Switch on electrical consumers (e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly when removing leads.Towing
Towing the vehicle The towing eye and wheel wrench are
stowed with the vehicle tools 3 290.
Disengage the cover using a suitable
tool and remove.
Screw the towing eye clockwise into
the front towing point and tighten fully using the wheel wrench.
Attach a tow rope – or better still a tow
rod – to the towing eye, never to the
bumper or front suspension units.

324Customer informationOperating data in the vehicleControl units process data for
operation of the vehicle.
This data includes, e.g.: ● vehicle status information (e.g. speed, movement delay, lateral
acceleration, wheel rotation rate, "seat belts fastened" display)
● ambient conditions (e.g. temperature, rain sensor,
distance sensor)
As a rule such data is transient, not
stored for longer than an operational
cycle, and only processed on board the vehicle itself. Control units often
include data storage (including the
vehicle key). This is used to allow
information to be documented
temporarily or permanently on vehicle
condition, component stress,
maintenance requirements and
technical events and errors.Depending on technical equipment
level, the data stored is as follows:
● system component operating states (e.g. fill level, tyre
pressure, battery status)
● faults and defects in important system components (e.g. lights,
brakes)
● system reactions in special driving situations (e.g. triggering
of an airbag, actuation of the
stability control systems)
● information on events damaging the vehicle
● for electric vehicles the amount of
charge in the high-voltage
battery, estimated range
In special cases (e.g. if the vehicle
has detected a malfunction), it may be
necessary to save data that would
otherwise just be volatile.
When you use services (e.g. repairs,
maintenance), the operating data
saved can be read together with the
vehicle identification number and
used when necessary. Staff working
for the service network ( e.g. garages,
manufacturers) or third parties (e.g.breakdown services) can read the
data from the vehicle. The same
applies to warranty work and quality
assurance measures.
Data is generally read via the OBD
(On-Board Diagnostics) port
prescribed by law in the vehicle. The operating data which is read out,
documents the technical condition of
the vehicle or individual components
and assists with fault diagnosis,
compliance with warranty obligations
and quality improvement. This data,
in particular information on
component stress, technical events,
operator errors and other faults, is
transmitted to the manufacturer
where appropriate, together with the
vehicle identification number. The
manufacturer is also subject to
product liability. The manufacturer
potentially also uses operating data
from vehicles for product recalls. This
data can also be used to check
customer warranty and guarantee
claims.
Fault memories in the vehicle can be
reset by a service company when
carrying out servicing or repairs or at
your request.

342IndexAAbsorptive Glass Mat battery .....274
Accessories and vehicle modifications .......................... 269
ACC files..................................... 153
Activating Bluetooth function ......197
Activating the navigation system 166
Activating voice recognition ........192
Active emergency braking ..104, 253
Adaptation volume km/h .............138
AdBlue ........................ 101, 234, 313
AdBlue gauge ............................... 93
AdBlue tank ................................ 317
Add a favourite destination .........177
Adding contacts to the phonebook .............................. 201
Adjustable air vents ...................221
AF (Alternative Frequency)......... 148
Airbag and belt tensioners ...........98
Airbag deactivation ................63, 98
Airbag label................................... 59 Airbag system .............................. 59
Air conditioning regular operation ................................ 223
Air conditioning system .............. 209
Air intake .................................... 223
Air suspension ........................... 231
Air suspension system................ 306
Air vents...................................... 221
Antifreeze ................................... 272Antilock brake system ................ 244
Antilock brake system (ABS) .....100
Anti-theft alarm system ................36
Anti-theft bolts............................. 299
Anti-theft locking system .............. 35
Anti-theft security lock ..................23
Appearance care ........................308
Armrest ........................................ 51
Ashtrays ....................................... 91
AST (Autostore list) ....................147
Audio players .............................. 129
Audio settings ............................. 137
Automatic call waiting .................201
Automatic light control ...............110
Automatic locking ...................24, 29
Automatic phone connection ......195
Automatic station search ............145
Automatic station storing ............147
Automatic switch-off ...................129
Automatic zoom .......................... 166
Autostop ....................... 18, 227, 228
Autostore lists ............................. 147
Auxiliary heater ........................... 216
AUX input ................................... 151
AUX input usage ........................152
Avoid part of route ......................183
B Balance....................................... 137
Bass............................................ 137

343Battery.................... 21, 22, 216, 274
Battery discharge protection ......117
Battery, jump starting.................. 304
Battery replacement ...................166
Belts.............................................. 55 Bluetooth .................................... 193
Bluetooth connection ..........156, 197
Bluetooth device list ...................197
Bluetooth music .......................... 156
Bonnet ....................................... 270
Bottle holders................................ 74
Brake assist ............................... 246
Brake fluid .......................... 274, 313
Brakes ............................... 244, 274
Brake system ............................. 100
Breakdown.................................. 306
Browse map................................ 183
Bulb replacement ....................... 277
Bus Rear seats ................................. 52
C Cabin bulkhead grille ....................80
Call lists ...................................... 201
Call waiting ................................. 201
Capacities .................................. 317
Cargo management system ........78
Car Pass ...................................... 21
Catalytic converter .....................234
Central locking system ................24Centre high-mounted brake light 282
Change Home location ...............166
Change passkey for Bluetooth connection ............................... 197
Change system language ...129, 139
Changing tyre and wheel size ...295
Charging system .......................... 99
Child locks ................................... 29
Child restraint installation locations ................................... 67
Child restraints.............................. 65
Child restraint systems ........65, 339
Cigarette lighter ........................... 91
Cleaning ..................................... 334
Cleaning the vehicle ...................308
Climate control ............................. 16
Climate control systems .............208
Clock ................... 88, 129, 139, 166
Coat hooks ................................... 74
Compass .................................... 166
Connecting an audio device .......156
Connection ................................. 195
Control elements overview .........122
Control indicators.......................... 95
Control of the vehicle .................225
Controls ........................................ 85
Convex shape .............................. 38
Coolant ....................................... 272
Coolant and antifreeze ...............313
Coolant heater ............................ 216Co-ordinates....................... 166, 177
Country information ............183, 200
Cruise control ....................103, 249
Cupholders .................................. 74
D DAB ............................................ 151
Danger, Warnings and Cautions ...4
Dashboard .................................... 11
Data sharing settings ..................129
Daytime running lights ...............113
Daytime running lights setting ....129
Deactivating Bluetooth function ..197
Deactivating guidance ................183
Declaration of conformity ....319, 335
DEF ............................................ 234
Defining the priority phone .........195
Delete a favourite destination .....177
Delete device from Bluetooth device list ................................ 197
Demisting and defrosting ..............16
Destination.................................. 166
Destination input ........................177
Dialling a telephone number .......201
Diesel exhaust fluid ....................234
Diesel fuel ................................... 262
Diesel fuel system bleeding .......276
Diesel particle filter ....................233
Digital audio broadcasting ..........151
Disconnecting an audio device ...156