door lock PEUGEOT 207 2011 User Guide

3ACCESS
74
DOORS


)
After unlocking the vehicle using the
remote control or the key, pull the
door handle.

From inside


)
Pull the front door control to open
the door; this unlocks the vehicle
completely.

)
Pull the rear door control to open
the door; this unlocks the door con-
cerned only.




Closing

If a door is not closed correctly:


- when the engine is running,
this warning lamp comes
on, accompanied by a mes-
sage in the multifunction
screen for a few seconds,

- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
in the multifunction screen for a few
seconds.


Opening


From outside

3
!i
i
ACCESS
75
If one of the doors or the boot is
open, the automatic central lock-
ing does not take place.











Centralised locking control

System which provides full manual
locking or unlocking of the doors from
the inside.

Locking


)
Press this button to lock the vehicle.
The red indicator lamp in the button
comes on.









Automatic central locking

This system automatically locks the
doors and boot while driving.
You can activate or deactivate this function.


Ignition on:
Activation


)
Press this button for more than
two seconds.
A confi rmation message appears in the
multifunction screen.

Unlocking


)
Above 6 mph (10 km/h), press this
button to unlock the doors, the boot
and the rear screen temporarily.
If one of the doors is open, the
central locking from the inside
does not take place.

Unlocking


)
Press this button again to unlock the
vehicle.
The red indicator lamp in the button
goes off.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors and boot lock au-
tomatically.
Deactivation


)
Press this button again for more
than two seconds.
A confi rmation message appears in the
multifunction screen.

When locking from the outside
When the vehicle is locked from
the outside, the red indicator lamp
fl ashes and the button is inactive.


)
Pull the interior door lever to
unlock the vehicle.

3ACCESS
76

Emergency control

System which locks or unlocks the
doors mechanically in the event of a
malfunction of the central locking.


)
Insert the key in the lock, located on
the edge of the door, then turn it one
eighth of a turn.

Locking the driver's door


)
Insert the key in the lock, then turn it
to the right.


Unlocking the driver's door


)
Insert the key in the lock, then turn it
to the left.


Locking the front and rear
passenger doors

Unlocking the front and rear
passenger doors


)
Pull the interior door opening control.


- when the engine is run-
ning
, this warning lamp
comes on, accompanied
by a message on the mul-
tifunction screen for a few
seconds,

- when the vehicle is moving
(speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a
few seconds.











Tailgate release

System for mechanical unlocking of the
boot in the event of a central locking
malfunction.

Unlocking


)
Fold back the rear seats to gain
access to the lock from inside the
boot.

)
Insert a small screwdriver into hole A

of the lock to unlock the tailgate.




Opening



)
After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate.

BOOT (SALOON)

Closing

If the tailgate is not closed correctly:

4
!
84
VISIBILITY
In fog or snow, the sunshine sen-
sor may detect suffi cient light.
Therefore, the lighting will not
come on automatically.
Do not cover the sunshine sen-
sor, coupled with the rain sensor
and located in the centre of the
windscreen behind the rear view
mirror; the associated functions
would no longer be controlled.

Coupling with the "Guide-me-home"
lighting
Association with the automatic illumination of
headlamps provides the "guide-me-home"
lighting with the following additional options:


- selection of the lighting duration to 15, 30
or 60 seconds in the vehicle parameters
in the multifunction screen confi guration
menu,

- automatic activation of "guide-me-home"
lighting when automatic illumination of
headlamps is in operation.











Automatic illumination
of headlamps
The sidelamps and dipped beam head-
lamps are switched on automatically,
without any action on the part of the
driver, when a low level of external light
is detected (sensor behind the rear view
mirror) or when the windscreen wipers
are switched on.
As soon as the brightness returns to a
suffi cient level or after the windscreen
wipers are switched off, the lighting is
switched off automatically.

"Guide-me-home" lighting

The dipped headlamps remain on tem-
porarily, after switching off the vehicle's
ignition, to make the driver's exit easier
in poor light.

Activation


)
With the ignition off, activate a
"headlamp fl ash" using stalk B
.

)
A second "headlamp fl ash" switches
the function off again.


Switching off
The "guide-me-home" lighting is switched
off automatically following the door lock-
ing command, after a given time.

Activation


)
Turn ring A
to the " AUTO
" position. The
automatic illumination of headlamps
is accompanied by a message in the
multifunction screen.

Operating fault
In the event of a malfunction of
the brightness sensor, the light-
ing comes on accompanied by
the service warning lamp, an
audible signal and a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.


Daytime running lamps *

On vehicles fi tted with daytime running
lamps, the dipped headlamps come on
when the vehicle is started.
This indicator lamp comes on
in the instrument panel.
The instruments and controls (multi-
function screen, air conditioning control
panel, ...) are not lit, unless the auto-
matic lighting mode is activated or the
lighting is switched on manually.

Deactivation


)
Turn ring A
to a position other than
" AUTO
". Deactivation is accompa-
nied by a message in the multifunction
screen.


*
According to country.

4
i
89
VISIBILITY
COURTESY LAMPS

3.
Rear courtesy lamp




Front and rear courtesy lamps

In this position, the courtesy
lamp comes on gradually:

Map reading lamps



)
With the ignition on, press the cor-
responding switch.
In permanent lighting mode, differ-
ent lighting times are available:


- with the ignition off, approxi-
mately ten minutes,

- in energy economy mode, ap-
proximately thirty seconds,

-
with the engine running, unlimited.




- when the vehicle is unlocked,

- when the key is removed from the
ignition,

-
when the remote control locking button is
activated, in order to locate your vehicle.

Permanently off.
Permanent lighting. It switches off gradually:


- when the vehicle is locked,

- when the ignition is switched on,

- 30 seconds after the last door is
closed.

1.
Front courtesy lamp


2.
Map reading lamp

5
!
CHILD SAFETY
95
ADVICE ON CHILD SEATS


Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the
seat belt passes correctly over the
child's thighs.
PEUGEOT recommends the use of
a booster seat which has a back, fi t-
ted with a seat belt guide at shoulder
level. The incorrect installation of a child
seat in a vehicle compromises the
child's protection in the event of an
accident.
Remember to fasten the seat belts
or the child seat harnesses keep-
ing the slack relative to the child's
body to a minimum, even for short
journeys.
When installing a child seat using
the seat belt, ensure that the seat
belt is tightened correctly on the
child seat and that it secures the
child seat fi rmly on the seat of your
vehicle. Move the seat forwards if
necessary.
For optimum installation of the "for-
wards-facing" child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle's seat
and that the head restraint does not
cause any discomfort.
If the head restraint has to be re-
moved, ensure that it is stored or
attached securely to prevent it from
being thrown around the vehicle in
the event of sharp braking. As a safety precaution, do not leave:


- a child or children alone and un-
supervised in a vehicle,

- a child or an animal in a vehicle
which is exposed to the sun,
with the windows closed,

- the keys within reach of children
inside the vehicle.
To prevent accidental opening of
the doors and rear windows, use
the "Child lock".
Take care not to open the rear windows
by more than one third.
To protect young children from the
rays of the sun, fi t side blinds on
the rear windows.
Children under the age of 10 must
not travel in the "forwards-facing"
position on the front passenger seat,
unless the rear seats are already
occupied by other children, cannot
be used or are absent.
Deactivate the passenger airbag
when a "rearwards-facing" child
seat is installed on the front seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
were to infl ate.

5
!
CHILD SAFETY
100
This system is independent and in
no circumstances does it take the
place of the central locking control.
Check the status of the child lock
each time you switch on the ignition.
Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
In the event of a serious impact,
the electric child lock is deactivated
automatically to allow the rear pas-
sengers to exit the vehicle.

MANUAL CHILD LOCK

Mechanical system to prevent opening of
the rear door using its interior control.
The control is located on the edge of
each rear door.


)
With the ignition key, turn the red
control one quarter of a turn:


- to the right on the left-hand rear
door,

- to the left on the right-hand rear
door.


ELECTRIC CHILD LOCK

Remote control system to prevent opening
of the rear doors using their interior controls.
The control is located in the centre of
the dashboard.


)
Press button A
.
The indicator lamp on button A
comes
on, accompanied by a message on the
multifunction screen.
Locking

Unlocking


)
With the ignition key, turn the red
control one quarter of a turn:


- to the left on the left-hand rear
door,

- to the right on the right-hand rear
door.



Activation

Deactivation


)
Press button A
again.
The indicator lamp on button A
switches
off, accompanied by a message on the
multifunction screen.

7
i!
DRIVING
116

Stopping the vehicle

Before switching off the engine, you
can engage position P
or N
to place the
gearbox in neutral.
In both cases, apply the parking brake
to immobilise the vehicle.

Operating fault

When the ignition is on, the
lighting of this warning lamp,
accompanied by an audible
signal and a message in the
multifunction screen, indicates a gear-
box fault.
In this case, the gearbox switches to
back-up mode and is locked in 3rd gear.
You may feel a substantial knock when
changing from P
to R
and from N
to R
.
This will not cause any damage to the
gearbox.
Do not exceed 60 mph (100 km/h), local
speed restrictions permitting.
Contact a PEUGEOT dealer or a quali-
fi ed workshop as soon as possible.
There is a risk of damage to the
gearbox:


- if you press the accelerator and
brake pedals at the same time,

- if you force the movement of
the gear lever from the P
po-
sition to another position when
the battery is fl at.
To reduce fuel consumption when
at a prolonged standstill with the
engine running (traffi c jam...), put
the gear lever in the N
position and
apply the parking brake.


Manual operation



)
Select position M
for sequential

changing of the four gears.

)
Push the lever towards the +
sign to
change up a gear.

)
Pull the lever towards the -
sign to
change down a gear.

D
disappears and the gears
engaged appear in succes-
sion on the instrument panel.
If the engine speed is too low
or too high, the gear selected
fl ashes for a few seconds, then the ac-
tual gear engaged is displayed.
It is possible to change from position D

(automatic) to position M
(manual) at
any time.
When the vehicle is stationary or mov-
ing very slowly, the gearbox selects
gear M1
automatically.
The sport and snow programmes do not
operate in manual mode. If the lever is not in position P
,
when the driver's door is opened
or approximately 45 seconds after
the ignition is switched off, a mes-
sage appears in the multifunction
screen.


)
Return the lever to position P
;
the message disappears.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit; otherwise, the
gearbox will operate temporarily in au-
tomatic mode.
Invalid value during manual
operation
This symbol is displayed if a
gear is not engaged correctly
(selector between two posi-
tions).

9PRACTICAL INFORMATION
150


Fuse N°



Rating



Functions




F8



20 A

Audio equipment, audio/telephone, multifunction
screen, clock, steering wheel controls, trailer
fusebox.


F9



30 A

Front 12 V socket, rear 12 V socket (SW).


F10



15 A

Not used.


F11



15 A

Diagnostic socket, low current ignition switch,
automatic gearbox control unit.


F12



15 A

Rain/sunshine sensor, amplifi er, trailer fusebox,
driving school module.


F13



5 A

Engine fusebox, ABS relay, dual-function brake
switch.


F14



15 A

Instrument panel, seat belt warning lamps panel,
headlamp adjustment, air conditioning, Bluetooth
system, rear parking sensors control unit, airbags.


F15



30 A

Locking.


F17



40 A

Heated rear screen and door mirrors.


SH



-

PARC shunt.

9
!
i
i
PRACTICAL INFORMATION
154
Do not charge the batteries with-
out disconnecting the terminals
fi rst.
Do not disconnect the terminals
while the engine is running.
The batteries contain harmful sub-
stances such as sulphuric acid
and lead. They must be disposed
of in accordance with regulations
and must not, in any circumstanc-
es, be discarded with household
waste.
Take used remote control batteries
and vehicle batteries to a special col-
lection point.
Charging the battery using a
battery charger


)
Disconnect the battery from the vehicle.


)
Follow the instructions for use pro-
vided by the manufacturer of the
charger.

)
Reconnect starting with the negative
terminal (-).

)
Check that the terminals and connec-
tors are clean. If they are covered with
sulphate (whitish or greenish deposit),
remove them and clean them.
It is advisable to disconnect the
battery if the vehicle is to be left
unused for more than one month.
Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.

Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
tems. However, if slight diffi cul-
ties are encountered following this
operation, contact a PEUGEOT
dealer or a qualifi ed workshop.
Referring to the corresponding
section, you must yourself reini-
tialise:


- the remote control key,

- the one-touch electric windows,

- the GPS satellite navigation
system.






Disconnecting the cables
Reconnecting the cables



)
Position the open clip 1
of the cable
on the positive terminal (+) of the
battery.

)
Press vertically on the clip 1
to position
it correctly against the battery.

)
Lock the clip by spreading the position-
ing lug and then lowering the tab 2
.


)
Raise the locking tab fully.
Do not force the tab as locking will
not be possible if the clip is not po-
sitioned correctly; start the proce-
dure again.