display Peugeot 207 CC 2011.5 Owner's Manual - RHD (UK. Australia)

15
FAMILIARISATION
MONITORING

Instrument panel
Switch panel



A.
With the ignition on, the fuel gauge
needle should rise.

B.
With the engine running, the associ-
ated low level warning lamp should
switch off.

C.
With the ignition on, the oil level in-
dicator should display "OIL OK"
for
a few seconds.
If the levels are not correct, top up the
level which is low.



20
Lighting of the indicator lamp indicates
the status of the corresponding function.


A.
Deactivation of the ESP/ASR system.



97

B.
Central locking.

74

C.
Deactivation of the interior volumetric
protection alarm.



69



1.
With the ignition on, the orange and
red warning lamps come on.

2.
With the engine running, these
warning lamps should switch off.
If a warning lamp remains on, refer to
the page concerned.



21



Warning lamps

17
FAMILIARISATION
DRIVING SAFELY

Speed limiter "LIMIT"
Display in the instrument panel



1.
Selecting/Switching off speed limiter
mode.

2.
Decrease the programmed value.

3.
Increase the programmed value.

4.
Speed limiter on/off.
The values must be set with the engine
running.



110
The cruise control or speed limiter mode
appears in the instrument panel when it
is selected.

1.
Selecting/Switching off cruise con-
trol mode.

2.
Decrease the programmed value.

3.
Increase the programmed value.

4.
Cruise control off/resume.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth gear
engaged on the manual gearbox (second
gear on the automatic gearbox).



112



Cruise control "CRUISE"
Cruise control

Speed limiter

18
ECO-DRIVING
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emissions.


Optimise the use of your
gearbox

With a manual gearbox, move off gen-
tly, change up without waiting and
drive by changing up quite soon. If
your vehicle has the system, the gear
shift indicator invites you to change up;
it is displayed in the instrument panel,
follow its instructions.

With an automatic or electronic gear-
box, stay in Drive "D"
or Auto "A"
, ac-
cording to the type of gearbox, without
pressing the accelerator pedal heavily
or suddenly.



Drive smoothly


Maintain a safe distance between vehi-
cles, use engine braking rather than the
brake pedal, and press the accelerator
progressively. These practices contrib-
ute towards a reduction in fuel consump-
tion and CO
2 emissions and also helps
reduce the background traffi c noise.

If your vehicle has cruise control, make
use of the system at speeds above
25 mph (40 km/h) when the traffi c is
fl owing well.



Control the use of your
electrical equipment

Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents be-
fore using the air conditioning.
Above 30 mph (50 km/h), close the win-
dows and leave the air vents open.
Remember to make use of equipment
that can help keep the temperature in
the passenger compartment down (sun-
roof and window blinds...).
Switch off the air conditioning, unless
it has automatic digital regulation, as
soon as the desired temperature is at-
tained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as
possible.

Switch off the headlamps and front
foglamps when the level of light does
not require their use.
Avoid running the engine before mov-
ing off, particularly in winter; your ve-
hicle will warm up much faster while
driving.

As a passenger, if you avoid connect-
ing your multimedia devices (fi lm, mu-
sic, video game...), you will contribute
towards limiting the consumption of
electrical energy, and so of fuel.
Disconnect your portable devices be-
fore leaving the vehicle.

1INSTRUMENTS and CONTROLS
20
PETROL - DIESEL, MANUAL OR AUTOMATIC GEARBOX,
INSTRUMENT PANELS
Panel which groups together the vehicle operation dials and indicator lamps.

5.
Screen.


6.
Display zero reset button.


Resets the selected function to
zero (trip distance recorder or
service indicator).

7.
Instrument panel lighting button.


Adjusts the brightness of the
lighting of the instruments and
controls.

8.
Automatic gearbox.


Indicates the programme selected
and the gear engaged.


Dials



1.
Rev counter.


Indicates the speed of rotation of
the engine (x 1 000 rpm).

2.
Fuel gauge.


Indicates the quantity of fuel
remaining in the tank.

3.
Coolant temperature.


Indicates the temperature of the
engine coolant (°Celsius).

4.
Speedometer.


Indicates the current speed of the
moving vehicle (mph or km/h).

A.
Speed limiter


or
Cruise control.


(mph or km/h)

B.
Trip distance recorder.


(miles or km/h)

C.
Service indicator.


(miles or km/h) then,
Engine oil level indicator.



then
Distance recorder.


(km or miles)
These three functions are displayed
in succession when the ignition is
switched on.
For more information, refer to the section
which corresponds to the function and to
the display associated with it.

Screen

1INSTRUMENTS and CONTROLS
28









Service indicator

System which informs the driver when
the next service is due, in accord-
ance with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero re-
set. It is determined by two parameters:


- the distance travelled,

- the time elapsed since the last service.
More than 1 000 km remain before
the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example:
4 800 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner
goes
off
; the distance
recorder resumes its normal operation.
The display then indicates the total and
trip distances.
Less than 1 000 km remain before
the next service is due

Example

:
900 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains on
to indicate that a service
must be carried out soon.

1
i
i
INSTRUMENTS and CONTROLS
29
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.













Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:


)
switch off the ignition,

)
press and hold the trip distance re-
corder zero reset button,

)
switch on the ignition; the distance re-
corder display begins a countdown,

)
when the display indicates "=0"
, re-
lease the button; the spanner disap-
pears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes
to
indicate that the service must be carried
out as soon as possible.

Example:
the service is overdue by
300 km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains
on
.

1INSTRUMENTS and CONTROLS
33
MONOCHROME SCREEN A (WITHOUT
PEUGEOT CONNECT SOUND)

Controls
Main menu

There are three display control buttons:


- "ESC"
to abandon the operation in
progress,

- "MENU"
to scroll through the men-
us or sub-menus,

- "OK"
to select the menu or sub-
menu required.


)
Press the "MENU"
button to scroll
through the various menus of the
main menu
:


- vehicle confi guration,

- options,

- display settings,

- language,

- units.

)
Press the "OK"
button to select the
menu required.

*
With air conditioning only.

Displays on the screen

This displays the following information:


- time,

- date,

- ambient temperature * (this fl ashes if
there is a risk of ice),

-
status of the openings (doors, boot ...),


- trip computer (refer to the end of the
section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Boot open") may ap-
pear temporarily. These can be cleared
by pressing the "ESC"
button.

1
!
INSTRUMENTS and CONTROLS
34

Vehicle confi guration

Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not ac-
tive, faulty).
Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or
km/l).


)
Once you have selected a setting,
press the "OK"
button to change its
value.

)
Wait for approximately ten sec-
onds without any action to allow
the changed data to be recorded or
press the "ESC"
button to cancel.
The screen then returns to the normal
display. Once the "Vehicle confi guration" menu
has been selected, you can activate or
deactivate the following equipment:


- directional headlamps (refer to the
"Visibility" section),

- "guide-me-home" lighting (refer to
the "Visibility" section).

For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when sta-
tionary.

1INSTRUMENTS and CONTROLS
35
MONOCHROME SCREEN A
Controls

Displays on the screen

This displays the following information:


- time,

- date,

- ambient temperature * (this fl ashes if
there is a risk of ice),

- status of the openings (doors,
boot...),

- audio sources (radio, CD...),

- trip computer (refer to the end of the
section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Boot open") may ap-
pear temporarily. These can be cleared
by pressing the "ESC"
button.


Main menu



)
Press the "MENU"
button to gain
access to the main menu
, then
press the " 
" or " 
" buttons to
scroll through the various menus:


- radio-CD,

- vehicle confi guration,

- options,

- display settings,

- language,

- units.

)
Press the "OK"
button to select the
menu required. From your Peugeot Connect Sound
control panel, you can:


)
press the "MENU"
button to gain
access to the main menu,


)
press the " 
" or " 
" buttons to scroll
through the items on the screen,

)
press the "MODE"
button to change
the permanent application (trip com-
puter, audio source...),

)
press the " 
" or " 
" buttons to
change a setting value,

)
press the "OK"
button to confi rm,
or


)
press the "ESC"
button to abandon
the operation in progress.

Radio-CD
With the Peugeot Connect Sound
switched on, once the "Radio-CD"
menu has been selected you can acti-
vate or deactivate the functions linked
with use of the radio (RDS, REG) or the
CD (introscan, shuffl e, CD repeat).
For more information on the "Radio-
CD" application, refer to the Peugeot
Connect Sound part of the "Audio and
Telematics" section.

*
With air conditioning only.

1
!
INSTRUMENTS and CONTROLS
36
For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when sta-
tionary.

Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.
Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).

Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or
km/l).


)
Once you have selected a setting,
press the " 
" or " 
" buttons to
change its value.

)
Press the " 
" or " 
" buttons to
switch respectively to the previous
or next setting.

)
Press the "OK"
button to record
the change and return to the normal
display or press the "ESC"
button to
cancel.

Vehicle confi guration

Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active, not
active, faulty). Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:


- directional headlamps (refer to the
"Visibility" section),

- "guide-me-home" lighting (refer to
the "Visibility" section).