ignition Peugeot 207 CC 2014 Owner's Guide

2
!
COMFORT
57
207CC_EN_CHAP02_CONFORT_ED01-2014
SUN VISOR
Component which protects against sunlight
from the front or the side, also equipped
with an illuminated courtesy mirror.
 With the ignition on, raise the conceal-ing fl ap; the mirror is lit automatically.
This sun visor is also equipped with a
ticket holder. To avoid any risk of jamming of the
pedals:
- only use mats which are suited
to the fi xings already present in
the vehicle; these fi xings must
be used,
- never fi t one mat on top of an- other.
The use of mats not approved by
PEUGEOT may interfere with ac-
cess to the pedals and hinder the
operation of the cruise control /
speed limiter.
The mats approved by PEUGEOT
have two fi xings located below the
seat.
MATS
Removable carpet protection.
Refitting
To refi t the mat on the driver's side:
 position the mat correctly,
 refi t the fi xings by pressing,
 check that the mat is secured cor- rectly.
Fitting
When fi tting the mat for the fi rst time,
on the driver's side use only the fi xings
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:
 move the seat as far back as possible,
 unclip the fi xings,
 remove the mat.

3
i
ACCESS
66
207CC_EN_CHAP03_OUVERTURES_ED01-2014
The vehicle will lock itself again
automatically after thirty seconds
unless a door is opened. This
system prevents unintentional un-
locking.
Please note that in this case, the
alarm will not be set.
The folding and unfolding of the
door mirrors can be deactivated by
a PEUGEOT dealer.
Folding the key
 First press button
A to fold the key.
Locating your vehicle
 Press the closed padlock to locate
your locked vehicle in a car park.
This is indicated by lighting of the cour-
tesy lamp and fl ashing of the direction
indicators for a few seconds. Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.
Anti-theft protection
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal
and a message in the screen.
In this case, your vehicle will not start;
contact a PEUGEOT dealer as soon as
possible.
 Press the boot unlocking
button on the remote control
for more than 2 seconds.
The boot opens slightly.
Unlocking and partially opening
the boot
Keep safely, away from your vehicle,
the label attached to the keys given to
you on acquisition of the vehicle.

3
i!
ACCESS
67
207CC_EN_CHAP03_OUVERTURES_ED01-2014
Starting the vehicle
 Insert the key in the ignition switch.
The system recognises the starting code.
 Turn the key fully towards the dash- board to position 3 (Starting) .
 When the engine starts, release the key.
Switching the vehicle off
 Immobilise the vehicle.
 Turn the key fully towards you to po-sition 1 (Stop) .
 Remove the key from the ignition switch.
Remote control problem
Following disconnection of the vehicle
battery, replacement of the remote con-
trol battery or in the event of a remote
control malfunction, you can no longer
unlock, lock or locate your vehicle.
 First of all, use the key in the lock to unlock or lock your vehicle.
 Then, reinitialise the remote control.
If the problem persists, contact a
PEUGEOT dealer as soon as possible. Changing the battery
Battery ref.: CR1620/3 volts.
Reinitialisation
 Switch off the ignition.

Turn the key to position 2 (Ignition on) .
 Press the closed padlock immedi-
ately for a few seconds.
 Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational
again. If the battery is fl at, you are in-
formed by illumination of this
warning lamp, an audible signal
and a message in the multi-
function screen.
 Unclip the casing using a coin at the notch.
 Slide the fl at battery out of its location.
 Slide the new battery into its loca- tion observing the original direction.
 Clip the casing.
 Reinitialise the remote control.
Key in ignition
If the key has been left in the igni-
tion, an audible signal is heard on
opening the driver's door. Switching off the engine leads to a
loss of braking assistance.

3
!
ACCESS
68
207CC_EN_CHAP03_OUVERTURES_ED01-2014
Lost keys
Go to a PEUGEOT dealer with the vehicle's registration document, your per-
sonal identifi cation documents and if possible the key code label.
The PEUGEOT dealer will be able to look up the key code and the transpon-
der code required to order a new key. Do not throw the remote control bat-
teries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
Remote control
The high frequency remote control is a sensitive system; do not operate \
it while it is in your
pocket as there is a possibility that it may unlock the vehicle, without\
you being aware of it.
Do not repeatedly press the buttons of your remote control out of range \
and out of sight
of your vehicle. You run the risk of stopping it from working and the remote control would\

have to be reinitialised.
No remote control can operate when the key is in the ignition switch, even when the igni-
tion is switched off, except for reinitialisation.
Locking the vehicle
Driving with the doors locked may make access to the passenger compart-
ment by the emergency services more diffi cult in an emergency.
As a safety precaution, never leave children alone in the vehicle, except for a
very short period.
In all cases, it is essential to remove the key from the ignition switch\
when
leaving the vehicle.
Anti-theft protection
Do not make any modifi cations to the electronic engine immobiliser system;
this could cause malfunctions.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a PEUGEOT
dealer, to ensure that only your keys can be used to open and start the vehicl\
e.

3
!
i
ACCESS
69
207CC_EN_CHAP03_OUVERTURES_ED01-2014
ALARM
System which protects and dissuades
against the theft of your vehicle. It pro-
vides two types of protection, exterior
and interior, as well as an anti-tamper
function.
Locking the vehicle with
full alarm
Do not make any modifi cations to
the alarm system, this could cause
malfunctions. In order to be taken into account,
this deactivation must be car-
ried out each time the ignition is
switched off.
In the "cabriolet" confi guration, the
interior protection is deactivated
automatically.
Locking the vehicle with
perimiter protection only
Activation
 Switch off the ignition and get out of
the vehicle.
 Lock or deadlock the vehicle using the locking button on the remote
control.
The alarm is activate; the indicator lamp
on button A fl ashes once per second.
The perimiter protection is activated
5 seconds after pressing the locking
button on the remote control.
The volumetric protection is activated
45 seconds after pressing the locking
button on the remote control.
If a door or the boot is open or not
properly closed, the vehicle is not
locked, but the perimiter protection will
be activated after 45 seconds at the
same time as the volumetric protection.
Exterior perimeter protection
The system detects opening of the vehicle.
The alarm is triggered if anyone tries to
enter the vehicle by forcing a door, the
boot or the bonnet.
Interior volumetric protection
The system detects any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks
a window or moves inside the vehicle.
If you wish to leave a pet in the vehicle
or a window partially open, deactivate
the interior protection.
Anti-tamper function
The system detects the putting out of
service of its components.
The alarm is triggered if anyone tries
to put the wires of the siren, the central
control or the battery out of service. Deactivation
 Unlock the vehicle using the unlock-
ing button on the remote control.
The alarm is deactivated; the indicator
lamp on button A switches off.
Deactivation of the interior
volumetric protection
 Switch off the ignition.
 Within ten seconds, press button A un-
til the indicator lamp is lit continuously.
 Get out of the vehicle.
 Quickly lock or deadlock the vehicle using the locking button on the re-
mote control.
The exterior perimeter protection alone
remains activated; the indicator lamp on
button A fl ashes once per second.

3
!
ACCESS
70
207CC_EN_CHAP03_OUVERTURES_ED01-2014
Triggering of the alarm
This is indicated by sounding of the si-
ren and fl ashing of the direction indica-
tors for approximately thirty seconds.
After it has been triggered, protection is
again operational. If the alarm is triggered ten times in
succession, the eleventh time will
result in it becoming inactive.
If the indicator lamp on button A
fl ashes rapidly, this indicates that
the alarm was triggered during
your absence. When the ignition is
switched on, this fl ashing stops im-
mediately.
To avoid triggering the alarm when
washing your vehicle, lock it using
the key in the driver's door lock.
Failure of the remote control
 Unlock the vehicle using the key in the driver's door lock.
 Open the door; the alarm is triggered.
 Switch on the ignition; the alarm stops.
* According to country.
Malfunction
When the ignition is switched on, light-
ing of the indicator lamp on button A for
ten seconds indicates a siren fault.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.
Locking the vehicle without
activating the alarm
 Lock or deadlock the vehicle using the key in the driver's door lock.
Automatic operation *
Depending on the legislation in force in
your country, one of these cases may
occur:
- 45 seconds after the vehicle is locked using the remote control, the alarm is
activated, regardless of the status of
the doors and boot.
- 2 minutes after the last door or the boot is closed, the alarm is activated.
 To avoid triggering the alarm on entering the vehicle, fi rst press the
unlocking button on the remote
control.
Reactivation of the interior
protection
 Unlock the vehicle using the unlock-
ing button on the remote control.
 Lock the vehicle again using the re- mote control.
The alarm is activate again with both
types of protection; the indicator lamp
on button A fl ashes once per second.

3
!
i
ACCESS
71
207CC_EN_CHAP03_OUVERTURES_ED01-2014
WINDOW CONTROLS
System which opens or closes a window
manually or automatically. It is fi tted with
a system which controls all four windows
on all models.
1. Driver's electric windows switch.
2. Passenger's electric windows switch.
Each window switch controls, on its
own side, the front window and the rear
quarter light.
One-touch electric windows
You have two options:
The windows (except the driver's
window) do not have an automatic
mode or safety anti-pinch function
for closing.
For your safety, the windows rise
in several stages; however, always
be vigilant.
The window control switches remain
operational for approximately 45 sec-
onds after the ignition is switched off
or until a door is opened.
 Press or pull switch
1 . The
window stops as soon as
the switch is released.
Electric windows
- manual mode
 Press or pull switch 1 gently. The
window stops as soon as the switch
is released.
The rear quarter light only opens once
the front window has opened completely.
- automatic mode
 Press switch 1 fully. The window
opens or closes completely when
the switch is released.
 Pressing the switch again stops the movement of the window.
 If you continue to press the switch, the rear quarter light will open or
close.
The rear quarter light only opens once
the front window has opened completely.

3
!
i
i
ACCESS
72
207CC_EN_CHAP03_OUVERTURES_ED01-2014
Switch for all four windows
This switch opens or closes all of the
windows.
Reinitialisation
Following reconnection of the battery or
in the event of a malfunction you must
reinitialise the operation of the electric
windows:
 release the switch and pull it again until it closes completely,
 hold the switch for approximately one second after closing,
 press the switch to lower the win- dow automatically,
 when the window has reached the low position, press the switch again
for approximately one second. Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
In the event of contact during op-
eration of the windows, you must
reverse the movement of the win-
dow. To do this, press the switch
concerned.
When the driver operates the pas-
senger electric window switches,
they must ensure that no one is
preventing correct closing of the
windows.
The driver must ensure that the
passengers use the electric win-
dows correctly.
Be particularly aware of children
when operating the windows.
 Press switch 3 and release it. The
windows open completely.
 Pressing the switch again stops the movement of the windows.
or
 Pull switch 3 and hold it in this posi-
tion. The windows close completely.
 If you release the switch before the windows have closed completely,
the windows stop.
This switch is operated under the
full responsibility of the driver. This procedure reinitialises the opera-
tion of the electric windows and the
automatic partial opening of the door
windows

3
i
i
ACCESS
74
207CC_EN_CHAP03_OUVERTURES_ED01-2014
If the vehicle is locked or dead-
locked from the outside, the red
indicator lamp fl ashes and button A
is inactive.
 In this case, use the remote control or the key to unlock the
vehicle.
Manual central locking control
System which provides full manual
locking or unlocking of the doors and
boot from the inside.
Locking
 Press button A to lock the vehicle.
The red indicator lamp in the button
comes on.
If one of the doors is open, the cen-
tral locking from the inside does not
take place. Unlocking
 With the key in the ignition, press
button A again to unlock the vehicle.
The red indicator lamp nn the button
goes off.

3
i
i
ACCESS
76
207CC_EN_CHAP03_OUVERTURES_ED01-2014
BOOT
Opening
 After unlocking the boot or the vehi-cle using the remote control or the
key, pull the handle and raise the
boot lid.
Unlocking and partially opening
the boot
 Press the boot unlocking button on the remote control
for more than two seconds.
The boot opens slightly.
If a battery failure occurs, the boot
is locked. Contact a PEUGEOT
dealer or a qualifi ed workshop.
Boot anti-theft protection
The boot is designed to remain secure,
even in the "cabriolet" confi guration.
So, when the vehicle is locked and the
roof is open, the boot cannot be un-
locked:
- by means of the interior door opening control, when the key is not in the
ignition switch,
- by pressing the manual centralised control A , when the key is not in the
ignition switch.
- when the engine is running , this warning lamp comes on,
accompanied by a message
on the multifunction screen
for a few seconds,
- when the vehicle is moving (speed above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a
few seconds.
Closing
 Lower the boot lid using the interior grab handle.
If the boot lid is not closed correctly: Automatic locking of the boot
In the "cabriolet" confi guration, with
the vehicle locked, if you unlock the
boot by pressing the boot unlock-
ing button on the remote control,
it will lock automatically when you
close it again.
In this case, if you inadvertently
leave the key in the boot, press the
manual centralised control
A im-
mediately to unlock the boot and
retrieve the key.