steering Peugeot 208 2017 User Guide

87
Advice
For the airbags to be fully effective,
observe the safety recommendations
below.
Adopt a normal and upright sitting position.
Wear a correctly adjusted seat belt.
Do not leave anything between the occupants
and the airbags (a child, pet, object, etc.), nor
fix or attach anything close to or in the way of
the airbag release trajectory; this could cause
injuries during their deployment.
Never modify the original definition of your
vehicle, particularly in the area directly
around the airbags.
After an accident or if the vehicle has been
stolen, have the airbag systems checked.
All work on the airbag system must be carried
out by a PEUGEOT dealer or a qualified
workshop.
Even if all of the precautions mentioned
are obser ved, a risk of injury or of minor
burns to the head, chest or arms when an
airbag is deployed cannot be ruled out. The
bag inflates almost instantly (within a few
milliseconds) then deflates within the same
time discharging the hot gas via openings
provided for this purpose.Front airbags
Do not drive holding the steering wheel by its
spokes or resting your hands on the centre
part of the wheel.
Passengers must not place their feet on the
dashboard.
Do not smoke as deployment of the airbags
can cause burns or the risk of injury from a
cigarette or pipe.
Never remove or pierce the steering wheel or
hit it violently.
Do not fit or attach anything to the steering
wheel or dashboard, this could cause injuries
in case of airbag deployment.
Curtain airbags
Do not attach anything or hang anything to
the roof, as this could cause head injuries
when the curtain airbag is deployed.
If fitted to your vehicle, do not remove the
grab handles installed on the roof, they play a
part in securing the curtain airbags.
Lateral airbags
Use only approved covers on the seats,
compatible with the deployment of the lateral
airbags. For information on the range of seat
covers suitable for your vehicle, you can
contact a PEUGEOT dealer.
Do not attach or hang anything to the seat
backrests (clothes, etc.) as this could cause
injuries to the thorax or arm when the lateral
airbag is deployed.
Do not sit with the upper part of the body any
nearer to the door than necessary.
The vehicle's front door panels include side
impact sensors.
A damaged door or any unauthorised or
incorrectly executed work (modification or
repair) on the front doors or their interior trim
could compromise the operation of these
sensors – Risk of malfunction of the lateral
airbags!
Such work must only be done by a PEUGEOT
dealer or a qualified workshop.
5
Safety

108
Starting – Switching off
the engine
Ignition switch
1.Stop position.
2. Ignition on position.
3. Starting position.
Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a malfunction.
Starting
F Insert the key into the ignition switch.
The system recognises the starting code.
With a manual gearbox
, place the gear
selector in neutral then fully depress the clutch
pedal.
With an electronic gearbox , place the gear
selector at N then press the brake pedal firmly. With an automatic gearbox
, place the gear
selector at P or N then press the brake pedal
f i r m l y.
F
U
nlock the steering column by
simultaneously turning the steering and the
key.
Driving

109
In some cases, you may have to apply
some force to turn the steering (if the
wheels are on lock against a kerb, for
example).
F

T
urn the key towards the dashboard to
position 3 (Starting) .
F

W
hen the engine starts, release the key.
Electronic immobiliser
The original key contains a coded electronic
chip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This protection against theft locks the engine
management system a few moments after the
ignition is switched off and prevents starting of
the engine following a break-in. In the event of a fault, you are
informed by lighting of this warning
lamp in the instrument panel, an
audible signal and a message in the
screen.
In this case, your vehicle will not start; contact
a PEUGEOT dealer as soon as possible.
Switching off
F Stop the vehicle.
F T urn the key towards you to position 1
(Stop) .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
Coasting
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active.
To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine. Switching off the engine leads to a loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2 (Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1 (Stop) , then back to position
2 (Ignition on) .
6
Driving

112
Electronic gearbox
5-speed
R.Reverse.
N. Neutral.
A. Automatic mode.
M. Manual mode.
6-speed
R.Reverse.
N. Neutral.
A. Automatic mode.
M. Manual mode. You can change from position A to M and
from M to A at any time.
Automatic mode
This mode allows gear changing
without action by the driver.
Moving off
Lever at position N
.
F
P
ress the brake pedal firmly.
F

S
tart the engine.
F

P
lace the lever at A or R .
F

R
elease the brake pedal and press the
accelerator pedal progressively.
If the engine does not start:
-
If N is flashing in the instrument panel, move
the gear lever to position A then to position
N .
-

I
f the Foot on the brake message is
displayed, press the brake pedal firmly.
The A , R or N position of the lever is indicated
in the display.
Stopping – Moving off on a slope
Do not use the accelerator to hold the vehicle,
but apply the parking brake.
Stopping – Parking
Place the lever at N and apply the parking
brake.
Manual gear change
This one-off gear change makes it possible
to overtake, for example, while remaining in
automated mode.
F

O
perate the steering mounted control
paddles + or - .
The gearbox engages the gear selected
if engine speed allows it. AUTO remains
displayed on the instrument panel.
After a few moments with no action on the
control paddles, the gearbox returns to
automatic operation.
Driving

113
Manual mode
This mode allows manual sequential gear
changing.
F
M
ove the selector lever to M .
F

P
ush the lever for ward to change
up.
F

P
ull the lever back to change
down.
Steering mounted control paddles
F Pull the "+" paddle to change up.
F P ull the "-" paddle to change up.
The gear engaged is indicated in the display.
Creep function
Depending on the engine, the vehicle moves
without pressing the accelerator.
Assistance with low-speed
manoeuvres
With the engine running at idle, parking brake
released and the lever placed at A , M or R, the
vehicle moves off when your release the brake
pedal.
It stops on opening the driver's door. Closing
the door, and putting your foot on the brake
or accelerator pedal allows movement of the
vehicle again. Following disconnection of the battery, you
have to reinitialise the gearbox.
F

S
witch on the ignition.
AUTO and – appear in the
instrument panel.
F
Sel
ect position N
.
F
P
ress the brake pedal firmly.
F
W
ait around 30 seconds until N or a gear
appears in the instrument panel.
F
R
elease the brake pedal.
The gearbox is operational again.
With the ignition on, if this warning
lamp comes on and AUTO flashes,
accompanied by an audible signal
and a message in the screen, this
indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
6
Driving

119
With BlueHDi Diesel and a manual gearbox:
- A s soon as the vehicle stops or the speed is
less than 2
mph (3 km/h) (with 1.5 Blue HDi
engine).
-

G
ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox :
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on which version
you have).
-

G
ear lever in neutral and clutch pedal
released (manual gearbox).
-

B
rake pedal pressed or gear lever in
position N (electronic or automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is active, The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
A time counter sums up the time
periods spent in STOP mode
during a journey. It resets every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as for
example, braking, power steering, With a manual gearbox in STOP mode, if
a gear is engaged without fully depressing
the clutch pedal, a warning lamp comes
on or an alert message is displayed asking
you to depress the clutch pedal to restart
the engine.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
START mode
The ECO warning lamp goes off and
the engine starts:
With a manual gearbox :
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released.
or
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the engine
is needed to control the system.
6
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving

123
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.In any event, the speed limiter cannot
replace the need to obser ve speed limits,
nor can it replace the need for vigilance on
the part of the driver.
Always pay attention to the profile of the
road and sharp acceleration and stay in
complete control of your vehicle.
To avoid any jamming under the pedals:
-

e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.
Cruise control "CRUISE"
System which automatically maintains the
speed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
Steering mounted controls
1.Cruise control mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Pause / Resume cruise control. This driving assistance system, for use when
the traffic is flowing, allows a speed set by
the driver to be maintained, except on a steep
gradient.
With a manual gearbox
In order for it to be programmed or activated,
the vehicle speed must be greater than 25
mph
(40 km/h) with 4
th gear or higher engaged.
With an electronic gearbox
To be registered or activated, the speed of the
vehicle must be above 25
mph (40 km/h) with
2
nd gear or higher engaged in manual mode, or
position A selected.
With an automatic gearbox
To be registered or activated, the speed of the
vehicle must be above 25
mph (40 km/h) with
2
nd gear or higher engaged in manual mode, or
position D selected.
Selection
F Place the thumbwheel at the "CRUISE"
position: the cruise control mode is selected
but is not switched on (PAUSE).
6
Driving

131
Park Assist
The system detects a parking space and then
provides assistance with the parallel parking
manoeuvres.
It controls the steering and provides visual and
audible information to the driver.
The driver manages the accelerator, brakes,
gears and the clutch in the case of a manual
gearbox.
The driver can take control at any time by
gripping the steering wheel.The Park Assist system cannot in any
circumstances replace the need for
vigilance on the part of the driver.
The driver must remain in control of their
vehicle ensuring that the space remains
clear during the manoeuvre.
In some circumstances, the sensors may
not detect small obstacles located in their
blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury! For entry into a parallel parking space the
system does not detect spaces which are
clearly much smaller or larger than the
size of the vehicle.
The "Parking sensors" function activates
automatically during the manoeuvres, it is
possible that a warning lamp illuminates
on the screen, accompanied by an audible
signal, without affecting the parking.
Changing tyre sizes (out-size tyres, winter
tyres, etc.) can inter fere with the correct
operation of the parking assistance
system.
When the Park Assist is active, it prevents
the Stop & Start going into STOP mode.
In STOP mode, activating Park Assist
restarts the engine.
Entering a parallel parking
space
F Once you have detected an available space,
limit the speed of the vehicle to 12 mph
(20


km/h).
F

P
osition your vehicle before this space.
The system provides assistance in entering and
exiting a parking space when parallel parking.
6
Driving

132
To activate the Park Assist system:
F
P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen.
F

S
elect the enter parking space manoeuvre.
The indicator lamp in the control comes on.
F

O
perate the direction indicator on the
parking side. F

M
ove for wards alongside the parking
space at a speed below 12
mph (20 km/h)
to measure it, keeping at a distance of
between 0.5 and 1.5
metres from the row of
parked vehicles.
Once measurement is complete, if the space is
large enough a message indicates that parking
is possible.
F

M
ove your vehicle for ward until a new
message is displayed. F

S
elect reverse and release the steering
wheel.
The assisted parking manoeuvre is in progress.
Without exceeding 5
mph (8 km/h), continue
the manoeuvres following the information given
by the "parking assistance" system, until the
end of manoeuvre message is displayed.
The indicator lamp in the control goes off,
accompanied by an audible signal.
Driving