lock Peugeot 208 2017 Owner's Guide

82
Warning lamp
Not fastened / unfastened.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel.
It remains on for a certain time if the front
passenger has not fastened their seat belt.
Once this period has elapsed, the warning lamp
goes off if the driver's seat belt is fastened.
From approximately 12
mph (20 km/h)
this warning lamp flashes for 2


minutes
accompanied by an audible signal of increasing
volume. Once these 2
minutes have elapsed,
this warning lamp remains on until the driver
and/or the front passenger fastens their seat
belt.
Release
F Press the red button on the buckle.
F G uide the seat belt as it reels in.
F

O
n the outer seat belts, raise the bar to the
top of the backrest to prevent the tongue
from knocking against the side trim.
Warning lamp
Unfastened.
From approximately 12 mph
(20
km/h) and for 2 minutes, this
warning lamp flashes, accompanied
by an audible signal of increasing
volume, when one or more rear
passengers unfasten their seat belt.
Once these two minutes have elapsed, this
warning lamp remains on until the one or more
rear passengers fasten their seat belt.
At the rear
The rear seats are each fitted with a three-point
seat belt equipped, for the outer seats, with a
force limiter.
Locking
F Pull the strap then insert the tongue in the buckle.
F

C
heck that the seat belt is fastened
correctly by pulling the strap.
Safety

83
Advice
The driver must ensure that passengers use
the seat belts correctly and that they are all
fastened before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not fulfil their role fully.
The seat belts are fitted with an inertia reel
permitting automatic adjustment of the length
of the strap to your size. The seat belt is
stowed automatically when not in use.
Before and after use, ensure that the seat belt
is reeled in correctly.
The lower part of the strap must be positioned
as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels have an automatic locking
device at the time of a collision, during
sudden braking or if the vehicle turns over.
You can release the device by pulling the
strap firmly and then releasing it so that it reels in slightly.
In order to be effective, a seat belt must:
-

b
e tightened as close to the body as
possible,
-

b
e pulled in front of you with a smooth
movement, checking that it does not twist,
-

b
e used to restrain only one person,
-

n
ot show any signs of cuts or fraying,
-

n
ot be converted or modified to avoid
affecting its performance.
In accordance with current safety regulations,
for all repairs on your vehicle's seat belts, go
to a qualified workshop with the skills and
equipment needed, which a PEUGEOT dealer
is able to provide.
Have your seat belts checked regularly by a
PEUGEOT dealer or a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy water or
a textile cleaning product, sold by PEUGEOT
dealers.
After folding or moving a seat or rear bench
seat, ensure that the seat belt is positioned and reeled in correctly.
Recommendations for children
Use a suitable child seat if the passenger is
less than 12
years old or shorter than one and
a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap.
For more information on Child seats , refer to
the corresponding section.
In the event of an impact
Depending on the nature and seriousness
of the impact , the pyrotechnic device may
be deployed before and independently of the
airbags. Deployment of the pretensioners
is accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp comes
on.
Following an impact, have the seat belts
system checked, and, if necessary, replaced,
by a PEUGEOT dealer or a qualified
workshop.
5
Safety

102
Advice
The incorrect installation of a child seat in a
vehicle compromises the child's protection in
the event of an accident.
Check that there is no seat belt or seat belt
buckle under the child seat as this could
make it unstable.
Remember to fasten the seat belts or the
child seat harnesses keeping the slack
relative to the child's body to a minimum,
even for short journeys.
When installing a child seat using the seat
belt, ensure that the seat belt is tightened
correctly on the child seat and that it secures
the child seat firmly on the seat of your
vehicle. If your passenger seat is adjustable,
move it for wards if necessary.
At rear seating positions, always leave
sufficient space between the front seat and:
-
a "
rear ward facing" child seat,
-

t
he feet of a child seated in a "for ward
facing" child seat.
For this, move the seat for ward and if
necessary straighten its backrest too. For optimal installation of the "forward facing"
child seat, verify that its backrest is as close
as possible to the backrest of the vehicle
seat, if possible in contact with it.
The head restraint must be removed before
installing a child seat with a backrest on a
passenger seat.
Ensure that the head restraint is stored or
attached securely to prevent it from being
thrown around the vehicle in the event of
sharp braking. Refit the head restraint once
the child seat has been removed.
Children in front
The legislation on carrying children on the
front passenger seat is specific to each
country. Refer to the legislation in force in
your country.
Deactivate the passenger's front airbag when
a rear ward facing child seat is installed on the
front passenger seat.
Otherwise, the child risks being seriously
injured or killed if the airbag is deployed. Installing a booster seat
The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs.
PEUGEOT recommends using a booster seat
with a backrest, equipped with a belt guide at
shoulder level.
As a safety precaution, do not leave:
-

a c
hild or children alone and unattended in
a vehicle,
-

a c
hild or an animal in a vehicle exposed
to the sun, with the windows closed,
-

t
he keys within the reach of children inside
the vehicle.
To prevent accidental opening of the doors
and rear windows, use the child lock.
Take care not to open the rear windows by
more than one third.
To protect young children from the rays of the
sun, fit side blinds on the rear windows.
Safety

103
Deactivation
F With the ignition on, press this button again.
The indicator lamp in the button goes off,
accompanied by a message to confirm
deactivation.
This indicator lamp remains off while the child
lock is switched off.Any other state of the indicator lamp
indicates a fault with the electric child
locks.
Have it checked by a PEUGEOT dealer or
a qualified workshop.
This system is independent and in no
circumstances does it take the place of
the central locking control.
Check the status of the child lock each
time you switch on the ignition.
Always remove the key from the ignition
when leaving the vehicle, even for a short
time.
Child lock
Manual system
Mechanical system to prevent opening of a rear
door using its interior control.
The control is located on the edge of each rear
d o o r.
Locking
F Using the ignition key, turn the red control as far as it will go:
-

t
o the left on the left-hand rear door,
-

t
o the right on the right-hand rear door.
Release
F Using the ignition key, turn the red control as far as it will go:
-

t
o the right on the left-hand rear door,
-

t
o the left on the right-hand rear door.
Electrical system
Electric system, with the control located at the
front, for locking the rear doors so that they
cannot be opened using their interior controls.
Activation
F With the ignition on, press this button.
The indicator lamp in the button comes on,
accompanied by a message confirming
activation.
This indicator lamp remains on all the time that
the child lock is activated
It is still possible to open the doors from the
outside and operate the rear electric windows
from the driver's control panel.
5
Safety

108
Starting – Switching off
the engine
Ignition switch
1.Stop position.
2. Ignition on position.
3. Starting position.
Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a malfunction.
Starting
F Insert the key into the ignition switch.
The system recognises the starting code.
With a manual gearbox
, place the gear
selector in neutral then fully depress the clutch
pedal.
With an electronic gearbox , place the gear
selector at N then press the brake pedal firmly. With an automatic gearbox
, place the gear
selector at P or N then press the brake pedal
f i r m l y.
F
U
nlock the steering column by
simultaneously turning the steering and the
key.
Driving

109
In some cases, you may have to apply
some force to turn the steering (if the
wheels are on lock against a kerb, for
example).
F

T
urn the key towards the dashboard to
position 3 (Starting) .
F

W
hen the engine starts, release the key.
Electronic immobiliser
The original key contains a coded electronic
chip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This protection against theft locks the engine
management system a few moments after the
ignition is switched off and prevents starting of
the engine following a break-in. In the event of a fault, you are
informed by lighting of this warning
lamp in the instrument panel, an
audible signal and a message in the
screen.
In this case, your vehicle will not start; contact
a PEUGEOT dealer as soon as possible.
Switching off
F Stop the vehicle.
F T urn the key towards you to position 1
(Stop) .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
Coasting
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active.
To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine. Switching off the engine leads to a loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2 (Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1 (Stop) , then back to position
2 (Ignition on) .
6
Driving

116
If the lever is not in position P, a message
appears in the screen on opening the
driver's door or approximately 45
seconds
after switching off the ignition.
F

P
lace the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, associated with
an audible signal and a message
on the screen, indicates a gearbox
fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R. This will not cause any
damage to the gearbox.
Do not exceed 60
mph (100 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible. There is a risk of damage to the gearbox:
F
i f you press the accelerator and brake
pedals at the same time,
F

i
f you force the movement of the lever
from position P to another position with
a flat battery.
To reduce fuel consumption during
prolonged stops with the engine running
(traffic jams, etc.), position the gear lever
at N and apply the parking brake.Gear shift indicator
(Depending on engine.)
This system reduces fuel consumption by
recommending the most appropriate gear.
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one (or more) gear(s). You can
follow this instruction without engaging the
intermediate gears.
Gearshift recommendations should not be
considered obligatory. The configuration of the
road, the amount of traffic and safety remain
determining factors when choosing the best
gear. The driver thus remains responsible
for deciding whether to follow or ignore the
system's instructions.
This function cannot be deactivated.
With an electronic or automatic gearbox,
the system is only active in manual mode.
Driving

131
Park Assist
The system detects a parking space and then
provides assistance with the parallel parking
manoeuvres.
It controls the steering and provides visual and
audible information to the driver.
The driver manages the accelerator, brakes,
gears and the clutch in the case of a manual
gearbox.
The driver can take control at any time by
gripping the steering wheel.The Park Assist system cannot in any
circumstances replace the need for
vigilance on the part of the driver.
The driver must remain in control of their
vehicle ensuring that the space remains
clear during the manoeuvre.
In some circumstances, the sensors may
not detect small obstacles located in their
blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury! For entry into a parallel parking space the
system does not detect spaces which are
clearly much smaller or larger than the
size of the vehicle.
The "Parking sensors" function activates
automatically during the manoeuvres, it is
possible that a warning lamp illuminates
on the screen, accompanied by an audible
signal, without affecting the parking.
Changing tyre sizes (out-size tyres, winter
tyres, etc.) can inter fere with the correct
operation of the parking assistance
system.
When the Park Assist is active, it prevents
the Stop & Start going into STOP mode.
In STOP mode, activating Park Assist
restarts the engine.
Entering a parallel parking
space
F Once you have detected an available space,
limit the speed of the vehicle to 12 mph
(20


km/h).
F

P
osition your vehicle before this space.
The system provides assistance in entering and
exiting a parking space when parallel parking.
6
Driving

138
Fuel tank
Capacity of the tank:
- approximately 50
litres (petrol engines).
-


approximately 50
litres (Diesel engines).
-


approximately 45


litres (Diesel BlueHDi
engines).
Low fuel level
When the low fuel level is reached
this warning lamp comes on in the
instrument panel. There remains
approximately 5


litres of fuel in
the tank. When the warning lamp
flashes, there is ver y little fuel left .
Refuel as soon as possible to avoid running
out.
For more information on Running out of fuel
(Diesel) , refer to the associated section.
With Stop & Start, never refuel with the
system in STOP mode; you must switch
off the ignition with the key.
Refuelling
A label on the inside of the fuel filler flap
reminds you of the type of fuel to use,
depending on your engine type. To refuel in complete safety:
F

Y
ou must switch off the engine.
F
O
pen the fuel filler flap 1.
F
I
nsert the key in the cap 2
, then turn it to the
left, F
F
ill up the tank but do not continue after
the 3
rd cut-off of the nozzle ; this could
cause malfunctions.
When you have finished filling the tank:
F

R

efit the filler cap.
F

T

urn the key to the right, then remove it from
the cap.
F

C

lose the fuel filler flap.
The key cannot be removed from the lock
until the cap is refitted.
Opening the filler cap may result in an
inrush of air. This is entirely normal and
results from the sealing of the fuel system.
If you have added the wrong fuel for
your vehicle, the fuel tank must be
drained and filled with the correct fuel
before star ting the engine.
Additions of fuel must be of at least 5

litres, in
order to be registered by the fuel gauge.
F

R

emove the cap and hook it onto the clip
located on the inside of the flap 3 .
Practical information

154
Topping up with AdBlue®
If you wish to top up yourself, please read
the following warnings carefully.
In cold weather, before per forming the top-up
ensure that the temperature is above -11°C.
Otherwise the AdBlue
® may be frozen and so
cannot be poured into the tank.
Park your vehicle in a warmer area for a few
hours to allow the top-up to be carried out.
F

B

efore topping up, ensure that the vehicle is
parked on a flat and level sur face.
F

S

witch off the ignition to stop the engine
and remove the key from the switch.
Access through the boot (1.6 litre
B lueHDi Euro 6.1)
F Raise the boot carpet then, depending on
equipment, lift out the spare wheel and/or
the storage box.
F

W
ithout pressing, turn the black cap a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

L

ift off the cap.
Access through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F With the vehicle unlocked, open the fuel
filler flap; the blue filler cap for the AdBlue®
tank is located to the right of the black fuel
filler cap.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

R

emove the blue cap.
Practical information