Car play Peugeot 208 2017 Owner's Manual

26
Resetting the service indicatorRetrieving the service
information
After each service, the service indicator must
be reset to zero.
If you have carried out the ser vice on your
vehicle yourself:
F

s
witch off the ignition,
If you have to disconnect the battery
following this operation, lock the vehicle
and wait at least 5
minutes for the reset to
be registered.
F

p
ress and hold the trip distance recorder
reset button,
F

s
witch on the ignition; the distance recorder
display begins a countdown,
F

w
hen the display indicates " =0", release
the button; the spanner disappears. You can access the ser vice information at any
time.
F

P
ress the trip distance recorder reset
button.
The ser vice information is displayed for a few seconds, then disappears.
Engine oil level indicator
(depending on version)
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a few
seconds, after the servicing information. The level read will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30
minutes.
Oil level incorrect
This is indicated by the display of the message
"Oil level incorrect" in the instrument panel
screen, accompanied by the ser vice warning
lamp and an audible signal.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
avoid damage to the engine.
For more information on Checking levels
,
refer to the corresponding section.
Oil level indicator fault
This is signalled by the display of the message
"Oil level measurement invalid" in the
instrument panel.
Contact a PEUGEOT dealer or a qualified
workshop.
Dashboard instruments

32
A few definitions
Range
(miles or km)The distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).
This value may fluctuate if a change
of driving style or terrain results in a
significant change in the current fuel
consumption.
Dashes are displayed when the range falls
below 20
miles (30 km).
After filling with at least 5
litres of fuel, the
range is recalculated and is displayed if it
exceeds 60
miles (100 km).
If dashes instead of figures continue to
be displayed when driving, contact a
PEUGEOT dealer or a qualified workshop.
The trip "
1" tab with:
-

A

verage speed for the first trip.
-
A

verage fuel consumption.
- D
istance travelled.
The trip " 2" tab with:
-

A

verage speed for the second trip.
-
A

verage fuel consumption.
-
D

istance travelled.
Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
Tr i p " 1" allows daily calculations to be carried
out, for example, and trip " 2" allows monthly
calculations.
Dashboard instruments

80
Reactivation
Deactivation can be configured in
the Driving / Vehicle menu.
It is confirmed by the display of a message.
These systems are reactivated automatically
each time the ignition is switched back on or
above 30

mph (50 km/h).
Below 30

mph (50 km/h), you can reactivate
them manually.
For the 1.6 THP 165 and THP 208 petrol
engines, the reactivation must always be
carried out manually.
Reactivating using the button F

P
ress this button again to
reactivate manually.
The indicator lamp in the button goes off. Reactivating using the touch screen
Reactivation can be configured in
the Driving / Vehicle menu.
It is confirmed by the display of a message.
Operating fault
Illumination of this warning lamp,
accompanied by the display of a
message and an audible signal,
indicates a fault with the system.
Contact a PEUGEOT dealer or a qualified
workshop to have the systems checked. ASR / DSC
These systems offer increased safety
in normal driving, but they should not
encourage the driver to take extra risks or
drive at high speed.
It is in conditions of reduced grip (rain,
snow, black ice) that the risk of loss of grip
increases. It is therefore important for your
safety to keep these systems activated in
all conditions, and particularly in difficult
conditions.
The correct operation of these
systems depends on obser vation of
the manufacturer's recommendations
regarding as much the wheels (tyres and
rims), braking and electronic components
as the assembly and repair procedures
used by PEUGEOT dealers.
The use of snow tyres is recommended,
in order to be able to benefit from the
efficiency of these systems in winter
conditions.
In this case, it is essential to equip the
four wheels with tyres approved for your
vehicle.
Deactivating using the touch screen
The systems no longer have an effect on
engine operation.
Safety

87
Advice
For the airbags to be fully effective,
observe the safety recommendations
below.
Adopt a normal and upright sitting position.
Wear a correctly adjusted seat belt.
Do not leave anything between the occupants
and the airbags (a child, pet, object, etc.), nor
fix or attach anything close to or in the way of
the airbag release trajectory; this could cause
injuries during their deployment.
Never modify the original definition of your
vehicle, particularly in the area directly
around the airbags.
After an accident or if the vehicle has been
stolen, have the airbag systems checked.
All work on the airbag system must be carried
out by a PEUGEOT dealer or a qualified
workshop.
Even if all of the precautions mentioned
are obser ved, a risk of injury or of minor
burns to the head, chest or arms when an
airbag is deployed cannot be ruled out. The
bag inflates almost instantly (within a few
milliseconds) then deflates within the same
time discharging the hot gas via openings
provided for this purpose.Front airbags
Do not drive holding the steering wheel by its
spokes or resting your hands on the centre
part of the wheel.
Passengers must not place their feet on the
dashboard.
Do not smoke as deployment of the airbags
can cause burns or the risk of injury from a
cigarette or pipe.
Never remove or pierce the steering wheel or
hit it violently.
Do not fit or attach anything to the steering
wheel or dashboard, this could cause injuries
in case of airbag deployment.
Curtain airbags
Do not attach anything or hang anything to
the roof, as this could cause head injuries
when the curtain airbag is deployed.
If fitted to your vehicle, do not remove the
grab handles installed on the roof, they play a
part in securing the curtain airbags.
Lateral airbags
Use only approved covers on the seats,
compatible with the deployment of the lateral
airbags. For information on the range of seat
covers suitable for your vehicle, you can
contact a PEUGEOT dealer.
Do not attach or hang anything to the seat
backrests (clothes, etc.) as this could cause
injuries to the thorax or arm when the lateral
airbag is deployed.
Do not sit with the upper part of the body any
nearer to the door than necessary.
The vehicle's front door panels include side
impact sensors.
A damaged door or any unauthorised or
incorrectly executed work (modification or
repair) on the front doors or their interior trim
could compromise the operation of these
sensors – Risk of malfunction of the lateral
airbags!
Such work must only be done by a PEUGEOT
dealer or a qualified workshop.
5
Safety

104
Eco-driving
Eco-driving is a range of everyday practices
that allow the motorist to optimise their fuel
consumption and CO
2 emissions.
Optimise the use of your gearbox
With a manual gearbox, move off gently and
change up without waiting. During acceleration
change up early.
With an automatic or electronic gearbox,
give preference to automatic mode and avoid
pressing the accelerator pedal heavily or
suddenly.
The gear shift indicator invites you to engage
the most suitable gear: as soon as the
indication is displayed in the instrument panel,
follow it straight away.
For vehicles fitted with an electronic or
automatic gearbox, this indicator appears only
in manual mode.
Drive smoothly
Maintain a safe distance between vehicles, use
engine braking rather than the brake pedal,
and press the accelerator progressively. These
practices contribute towards a reduction in fuel
consumption and CO
2 emissions and also help
reduce the background traffic noise.
If your vehicle has cruise control, make use of
the system at speeds above 25
mph (40 km/h)
when the traffic is flowing well.
Control the use of your electrical
equipment
Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before using
the air conditioning.
Above 30
mph (50 km/h), close the windows
and leave the air vents open.
Consider using equipment that can help keep
the temperature in the passenger compartment
down (sunroof and window blinds, etc.).
Unless it has automatic regulation, switch off
the air conditioning as soon as the desired
temperature has been reached.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as possible. Switch off the headlamps and front foglamps
when the ambient light level does not require
their use.
Avoid running the engine before moving off,
particularly in winter; your vehicle will warm up
much faster while driving.
As a passenger, if you avoid connecting your
multimedia devices (film, music, video game
etc.), you will contribute towards limiting the
consumption of electrical energy, and so of
fuel.
Disconnect your portable devices before
leaving the vehicle.
Limit the causes of excess
consumption
Spread loads throughout the vehicle; place the
heaviest items in the bottom of the boot, as
close as possible to the rear seats.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof rack,
bicycle carrier, trailer, etc.). Use a roof box in
preference.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and
refit your summer tyres.
Driving

115
F Push the lever for ward to change up.
F

P
ull the lever back to change
down.
Invalid value
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).
You can change from position D to M and
M to D at any time.
If position R , D or M is selected when the
engine is running at idle, with the brakes
released, the vehicle moves even without
the accelerator being pressed.
Never leave children unattended in the
vehicle when the engine is running.
When carrying out maintenance with the
engine running, apply the parking brake
and select position P . Never select position N while the vehicle
is moving.
Never select position P or R unless the
vehicle is completely stationary.
If position N is selected inadvertently while
driving, allow the engine to return to idle,
then select position D to accelerate.
If the temperature is below -23°C, the
engine should be left at idle for four
minutes, to ensure the correct operation
and life of the engine and gearbox.
Sport programme
This special programme completes the
automatic operation of the gearbox in certain
circumstances.
F

W
ith the engine running, press
button S.
The gearbox automatically favours a dynamic
style of driving.
S appears on the instrument panel.
Snow program
This special program completes the automatic
operation and makes it easier to move off and
make progress in conditions of poor grip.
F

W
ith the engine running, press
the T button.
The gearbox adapts to driving on slippery
roads.
T appears on the instrument panel.
Return to automatic
operation
F Press the button again at any time to quit the program and
return to auto-adaptive mode.
Stopping – Parking
Before switching off the engine.
F M ove the lever to position P or N .
F

A
pply the parking brake.
F

Imm
obilise the vehicle.
6
Driving

126
When changing the programmed
reference speed by means of a maintained
press, pay attention as the speed can
increase or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.Memorising speeds
This function allows speeds to be saved, which
can then be offered to set the two systems: the
speed limiter (to limit the speed of the vehicle)
or the cruise control (for a vehicle cruising
speed).
You can memorise up to five settings in the
system for each of the two systems.
By default, some speed settings are already
memorised.
With touch screen
This memorisation can be
configured from the menu Driving /
Vehicle .
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting Speeds " function.
F

P

ress " ON" to activate the function.
F

Sel

ect the speed setting 1 to 5 that you want
to change.
F

S

elect the speed setting value you want to
change.
F

E

nter the new value using the numerical
keypad and confirm and click on " OK" to
confirm. As a safety measure, the driver must carry
out these operations when stationary.
Selection
To select a memorised speed:
F
P ress and hold the " +" or " -" button; the
system stops at the nearest memorised
speed.
F

P
ress and hold again the " +" or " -" button to
select another memorised speed.
A reminder of the speed and the state of the
system (on / off) is displayed in the instrument
panel.
Driving

128
The collision can be automatically avoided
if the speed difference between your
vehicle and the one ahead is not more
than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
Activation / Deactivation
It is possible to activate or
deactivate the Active City Brake
from the Driving / Vehicle menu.
The system state remains in memory when the
ignition is switched off.
Each subsequent time the ignition is switched
on, if the automatic emergency braking function
is deactivated, a temporary message will
be displayed indicating the speed threshold
(6

mph (10 km/h)). Please deactivate the Active City
Brake:
-

F
ollowing impact damage to the
windscreen close to sensor,
-
W
hen towing a trailer,
-
W
hen the vehicle is being towed,
-
W
hen the vehicle is about to cross a
toll barrier.
-
W
hen the vehicle is passing through
an automatic car wash,
Operating limits
Not detected are:
- Pe destrians, animals, motorcyclists,
cyclists.
-

F
ixed and non-reflective materials and
objects (cardboard box, wall, etc.).
-

V
ehicles not travelling in the same direction.
This system will not trigger or inter vene if the
driver:
-

p
resses the accelerator pedal firmly,
-

t
urns the wheel sharply (avoiding
manoeuvre).
-

m

ay stop the vehicle, holding the brakes on
for around 1.5

seconds when stationary to
allow the driver time to take back control of
the vehicle,
-

m

ay cause the engine to stall,
-

m

ay give rise to a pumping noise, due to the
pressurisation of the braking system.
Operating faults
Clean or clear any dirt, mist or objects (stickers,
leaves, etc.) from the top of the windscreen that
could obstruct the laser's field of vision. In the following cases, you should have the
system checked by a PEUGEOT dealer or a
qualified workshop:
-

T
he message "
Automatic braking system "
fault detected accompanied by an audible
signal indicates that a fault has been
detected.
-
F
ollowing an impact, the system is
automatically put out of ser vice, it no longer
works. The system detects the deployment
of airbags.
Do not attempt to remove, adjust or test
the sensor.
Only a PEUGEOT dealer or a qualified
workshop is able to work on the system.
Misting of the windscreen or accumulations
of snow on the bonnet could inter fere with the
operation of the laser. A message appears if
the laser is obstructed.
Use windscreen demisting and regularly clean
the area of the windscreen in front of the
sensor.
Be particularly vigilant when driving in poor
weather (very heavy rain, hail, fog, snow, etc.).
This is because braking distances increase
while the laser's calculation parameters remain
the same.
Driving

130
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow.
The system will be deactivated
automatically if a trailer is being towed or if
a bicycle carrier is fitted (vehicle fitted with
a towbar or bicycle carrier recommended
by PEUGEOT).
The parking sensor system cannot in
any circumstances replace the need for
vigilance on the part of the driver.Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, etc.).
Some deformation of the image is normal.
The blue lines represent the general direction
of the vehicle (the gap represents the width of
your vehicle except for the door mirrors).
The red lines represent a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The superimposed representation of guide
lines helps with the manoeuvre. The reversing camera cannot, in any
circumstances, replace the need for
vigilance on the part of the driver.
High pressure jet wash
When washing your vehicle, do not direct
the lance within 30
cm of the camera lens.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a soft, dry cloth.
Driving

135
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change.
The system triggers an alert as soon as it
detects a drop in the pressure of one or more
tyres.
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check the
tyre inflation pressure (including the spare
wheel) every month as well as before a
long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on Identification
markings , including in particular the tyre
pressure label, refer to the corresponding
section.
Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
In the contrary case(hot), add 0.3
bar to
the values indicated on the label.
Under-inflation alert
This is indicated by fixed illumination
of this warning lamp, an audible
signal and, depending on the
equipment installed, a message
displayed on the screen.
F

R

educe speed immediately, avoid excessive
steering movements and sudden braking. The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not be satisfied with just a visual
check.
F
I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F
i
f you have a compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
or
F
i
f it is not possible to make this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
F

S
top the vehicle as soon as it is safe to do
so.
6
Driving