ESP Peugeot 208 2019 Service Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2019, Model line: 208, Model: Peugeot 208 2019Pages: 263, PDF Size: 9.61 MB
Page 134 of 263
132
F Insert a flat screwdriver between the door
mirror glass and its base.
F
T
ilt the screwdriver and use it as a lever to
extract the glass.
F
U
nclip the shell of the door mirror by
pressing on the two fixing clips.
F Press the central tab and remove the side repeater.
F
P
ull out the bulb holder and replace the faulty bulb.
To refit, carry out these operations in
reverse order.
To replace this type of bulb, you can also
contact a
PEUGEOT dealer or a qualified
workshop.
Rear lamps
1. Brake lamps (LED).
2. Reversing lamps (P21W).
3. Direction indicators (PY21W amber).
4. Sidelamps (LED).
5. Foglamp (P21W).
LEDs: light-emitting diodes.
Reversing lamps and direction
indicators
These two bulbs are changed from inside the
boot:
F
O
pen the boot. F
R
emove the access grille from the
corresponding side trim panel.
F
U
nscrew and remove the nut.
F
D
isconnect the lamp unit connector.
F
U
nclip the lamp unit and carefully extract it
pulling straight towards you.
Integrated direction indicator
side repeaters
F Press the four tabs and remove the bulb h o l d e r.
F
T
urn the bulb a quarter turn, pull it out and
fit a
new bulb.
To refit, carry out these operations in reverse
o r d e r.
In the event of a breakdown
Page 135 of 263
133
Third brake lamp
F Unscrew the fixing pins on each side of the lamp unit, without removing them
completely.
F
P
ush on the screws to unclip the lamp unit.
F
D
isconnect the lamp unit connector.
F
R
emove the lamp unit from the outside.
F
T
urn the bulb holder corresponding to the
faulty bulb a
quarter turn and pull it out.
F
P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
Number plate lamps
To facilitate removal, per form this procedure
with the tailgate half open.
F
I
nsert a thin screwdriver into the cut-out
outside the lens.
F
P
ush it outwards.
F
R
emove the lens.
F
R
eplace the faulty bulb.
To refit, press the lens to clip it in.
Foglamp
Make sure to engage the lamp unit in its guides
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
For access, pass your hand under the bumper.
F
T
urn the bulb holder a quarter turn and pull
it out. F
D isconnect the bulb connector.
F
P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
For the replacement of these bulbs, you can
also contact a
PEUGEOT dealer or a qualified
workshop.
Changing a fuse
Access to the tools
The extraction tweezers are fitted to the back
of the dashboard fusebox cover or glove box
fusebox cover.
Dashboard
8
In the event of a breakdown
Page 136 of 263
134
F Unclip the cover by pulling at the top left, then right.
F
D
isengage the cover fully and turn it over.
F
R
emove the carrier on the back of which the
tweezers are fitted.
Glove box
F Open the glove box lid.
F U nclip the fusebox cover by pulling at top
right.
F
D
isengage the cover completely and turn it
ove r.
F
R
emove the carrier on the back of which the
tweezers are fitted. F
a
ll electrical consumers must be switched
of f,
F
i
dentify the failed fuse using the allocation
tables and the diagrams given in the
following pages.
To remove or fit a fuse, it is essential to:
F
u
se the special tweezers to extract the fuse
from its housing and check the condition of
its filament.
F
a
lways replace the failed fuse with a fuse
of the same rating (same colour); use of
a
different rating may cause malfunctions
(risk of fire).
If the fuse fails again soon after replacement,
have the vehicle's electrical system checked by
a PEUGEOT dealer or a qualified workshop.
Professional repairers: for full information
on the fuses and relays, consult the
"Methods" wiring information and diagrams
available from a
PEUGEOT dealer.
The fuse allocation tables and the
corresponding diagrams are available
from a PEUGEOT dealer or from
a
qualified workshop.
The replacement of a
fuse not shown in
the allocation tables below may cause
a
serious malfunction of your vehicle.
Contact a
PEUGEOT dealer or a qualified
workshop.
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your vehicle,
contact a
PEUGEOT dealer or a qualified
workshop.
Good
Failed
Tw e e z e r s
Before changing a
fuse:
F
i
mmobilise the vehicle and switch off the
ignition,
In the event of a breakdown
Page 137 of 263
135
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with specifications, in particular when the
combined power consumption of all of the
additional equipment connected exceeds
10
milliamperes.
Left-hand side
Fuse N° Rating Functions
F2 5
ADoor mirrors,
headlamps,
diagnostic socket.
F9 5
AAlarm.
F10 5
AIndependent
telematic unit, trailer
interface unit.
F11 5
AElectrochrome
interior rear view
mirror, additional
heating.
F13 5
AHi-Fi amplifier,
parking sensors.
F16 15
AFront 12
V socket.
F17 15
AAudio system, audio
system (accessory).
F18 20
ATouch screen. Fuse N°
Rating Functions
F23 5
AVanity mirrors, map
reading lamps.
F26 15
AHorn.
F27 15
AScreenwash pump.
F28 5
AAnti-theft.
F29 15
AAir conditioning
compressor.
F30 15
ARear wiper.
8
In the event of a breakdown
Page 142 of 263
140
Quick-release terminal clamp
Disconnecting the (+) terminalReconnecting the (+) terminal
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Before disconnecting
Wait 2 minutes after switching off the ignition
b efore disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection
After each time that the battery has been
reconnected, switch on the ignition and wait
1
minute before starting the engine, to allow
the electronic systems to initialise. However,
if minor problems persist after this procedure,
contact a
PEUGEOT dealer or a qualified
workshop.
Referring to the corresponding section, you
must yourself reinitialise:
-
t
he remote control key,
-
t
he date and time,
-
t
he radio preset stations.
F
Ra
ise the lever A fully to release the
clamp B .
F
R
emove the clamp B by lifting it off. F
Ra
ise the lever A fully.
F
R
efit the open clamp B on the (+) terminal.
F
P
ush the clamp B fully down.
F
L
ower the lever A to lock the clamp B .
To w i n g
Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
F
s
witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F
s
witch off the ignition and wait for 4
m
inutes.
At the battery, it is only necessary to
disconnect the (+) terminal.
In the event of a breakdown
Page 144 of 263
142
Engine technical data and
towed loads
Engines
The engine characteristics are given in the
vehicle's registration document, as well as in
sales brochures.The maximum power corresponds to the
value type-approved on a
test bed, under
conditions defined in European legislation
(Directive 1999/99/EC).
For more information, contact a
PEUGEOT
dealer or a
qualified workshop.
Weights and towed loads
The weights and towed loads relating to your
vehicle are given in the registration document,
as well as in sales brochures.
These values are also given on the
manufacturer's plate or label.
For more information, contact a PEUGEOT
dealer or a
qualified workshop. The GTW (Gross Train Weight) and towed load
values indicated are valid up to a
maximum
altitude of 1,000 metres. The towed load value
must be reduced by 10% for each additional
1,000 metres of altitude.
The maximum authorised nose weight
corresponds to the weight permitted on the
towball.
When exterior temperatures are high,
the vehicle per formance may be limited
in order to protect the engine. When the
exterior temperature is higher than 37°C,
limit the towed weight.
Towing using a lightly loaded vehicle can
adversely affect roadholding.
Braking distances are increased when
towing a trailer.
When using a vehicle to tow, never
exceed a
speed of approximately 60 mph
(100
km/h) (obser ve the local legislation
in force).
If the exterior temperature is high, it is
recommended that the engine is allowed
to idle for 1
to 2 minutes after the vehicle
comes to a
stop, to facilitate its cooling.
Technical data
Page 152 of 263
2
Steering mounted controls
Radio: select the previous/next
preset radio station.
Select the previous/next item in
a menu.
Radio: automatic search for a
higher
frequency.
CD/MP3: select the next track.
CD: press and hold: fast for ward.
Change the audio source.
Confirm a
selection.
Radio: automatic search for a
lower
frequency.
CD/MP3: select the previous track.
CD: press and hold: rewind.
Increase volume.
Decrease volume.
Mute on: cut the sound by
simultaneously pressing the volume
up and down buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press the SRC/BAND button
repeatedly to select the FM1, FM2 or
AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing the list
Press LIST to display the list of
stations received in alphabetical
o r d e r. Select the desired radio station by
pressing one of the buttons.
Confirm with OK.
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST
to build or
update the list of stations; audio
reception is cut momentarily.
Press MENU .
Select " Radio".
Confirm with OK.
Select " RDS".
RDS
RDS, if displayed, allows you to continue
listening to the same station by automatically
retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS
station may not be assured throughout the
entire country as radio stations do not cover
100% of the territory. This explains the loss
of reception of a
station during a journey.
Audio system
Page 156 of 263
6
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). To allow for optimal listening quality, the audio
settings (Volume, Bass, Treble, Ambience,
Loudness) can be tailored to different
sound sources, which can generate audible
differences when changing source (radio, CD,
e t c .) .Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-
Rear Fader, Left-Right Balance) to the middle
position, select the musical ambience "None"
and set the loudness correction to the "Active"
position in CD mode or to the "Inactive" position
in radio mode.
When changing the settings for treble and bass,
the ambiance setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is not possible.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are not
working (no sound, 87.5
MHz is displayed, etc.).The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area. Activate the RDS mode and start a
new search
for the station so that the system can check
whether a
stronger transmitter is available in the
geographic area.
The environment (hills, buildings, tunnels,
basement car parks, etc.) blocks reception,
including in RDS tracking mode. This phenomenon is normal and does not
indicate a
failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a
car wash or into
an underground car park). Have the aerial checked by a
PEUGEOT dealer.
Audio system
Page 159 of 263
1
Audio system/Bluetooth®
Contents
First steps
1
S
teering mounted controls
2
R
adio
2
M
edia
3
T
elephone
6
A
udio settings
8
C
onfiguration
9
F
requently asked questions
9
F
or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode.First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a
lower radio
frequency.
Select the previous CD, USB track.
Scroll in a
list.
Press and hold: rewind. Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a
higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
Select preset radio station.
Radio, press and hold: store
a
station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, AM, CD, USB,
AUX, Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a
call, access the calls log for the
connected telephone.
.
Bluetooth® audio system
Page 160 of 263
2
Steering mounted controls
Radio: select the previous/next
preset radio station.
CD/USB: select the genre/artist /
folder from the classification list.
Select the previous/next item in
a menu.
Radio: automatic search for higher
frequency.
CD/MP3/USB: select the next track.
CD/USB: press and hold: fast
forward.
Change the audio source.
Confirm a
selection.
Call/end call on the telephone.
Press and hold: access to the calls
list.
Radio: automatic search for lower
frequency.
CD/MP3/USB: select the previous
track.
CD/USB: press and hold: rewind.
Increase volume.
Decrease volume. Mute on: cut the sound by
simultaneously pressing the volume
increase and decrease buttons.
Mute off: press one of the two
volume buttons.
Radio
Presetting a station
Press SRC/TEL
repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a
button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset.
The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a
normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
c orresponding preset station.
Managing a list
Press LIST to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
Bluetooth® audio system