light Peugeot 307 2007.5 Repair Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 307, Model: Peugeot 307 2007.5Pages: 212, PDF Size: 7.59 MB
Page 111 of 212
DRIVING
98
HANDBRAKE
Applying
Pull the handbrake to immobilise
your vehicle. When the vehicle is being
driven, illumination of
this warning light and
of the STOP warning
light, accompanied by an
audible signal and a message on the
multifunction etdisplay, indicates that
the handbrake is still on or has not
been properly released.
When parking on a slope,
direct your wheels towards
the pavement and pull the
handbrake.
Releasing
Pull on the handle and press the
button to release the handbrake.
The four or six speed automatic
gearbox offers a choice between
the comfort of integral automatic
operation , enhanced by a sport and
a snow programme, or manual gear
changing .
P ark: to immobilise the vehicle or
start the engine , with the handbrake
on or off.
R everse: to reverse (select this
position with the vehicle stationary,
engine at idle).
N eutral: to start the engine and to
park , with the handbrake on.
Note: if position N is engaged
inadvertently while driving, allow
the engine to return to idle before
engaging position D to accelerate.
D rive: for driving in automatic
mode.
M anual: to select the gears.
S : sport programme.
: snow programme.
Gear selection gate
Move the lever in the gate to
select a position.
The indicator light for the selection is displayed on the instrument
panel display.
Starting the engine
with the handbrake applied,
select position P or N in the gate,
turn the ignition key to the
Starting position.
Otherwise, you are warned by an
audible signal and a message on the
multifunction display.
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX
Page 113 of 212
DRIVING
100
Manual operation
Manual changing of the four or six
gears:
select position M in the gate,
push the lever to the + sign to
change to a higher gear,
pull the lever to the - sign to
change to a lower gear.
You can change from position D
(driving in automatic mode) to
position M (driving in manual mode)
at any time.
Invalid value during manual
operation Notes
It is only possible to change from
one gear to another if the vehicle
speed and engine speed permit. If
they do not, the vehicle will operate
temporarily in automatic mode.
In the event of under-revving or over-
r e v v i n g , t h e g e a r s e l e c t e d l a s h e s f o r
a few seconds, then the actual gear
engaged is displayed.
When the vehicle is stationary or
moving very slowly, the gearbox
automatically selects gear
M1 .
Programme S (sport) and (snow)
do not operate in manual mode.
Operating abnormality
Any operating abnormality
is indicated by the
displaying of this warning
light, an audible signal and
a message on the multi-
function display.
In this situation the gearbox operates in
downgrade mode (locked in 3rd gear).
You may feel a substantial knock when
changing from P to R and from N to R
(this will not cause any damage to the
gearbox).
Do not exceed 60 mph (100 km/h),
keeping within the limit of local speed
restrictions.
Contact a PEUGEOT dealer as soon
as possible.
I f t h e b a t t e r y i s l a t a n d t h e
lever is in position P , it will
be impossible to change to
another position.
Above all, do not force the lever
as there is a risk of damage to the
automatic gearbox.
This is displayed if a gear
is not engaged correctly
(selector between two
positions).
Page 120 of 212
DRIVING
107
VISUAL AND AUDIBLE REAR
PARKING ASSISTANCE
This system consists of four proximity
sensors, located in the rear bumper.
This detects any obstacle (person,
vehicle, tree, gate, etc.) behind the
vehicle. Nevertheless, it cannot
detect obstacles located just below
the bumper.
An object, such as a stake, a
roadworks cone or any other similar
object may be detected at the
beginning of the manoeuvre, but
may no longer be detected when the
vehicle comes close to it.
Note: this function will be disarmed
automatically when the vehicle is
towing a trailer or when a bicycle
c a r r i e r i s i t t e d ( v e h i c l e i t t e d w i t h
towing attachment or bicycle carrier
recommended by PEUGEOT).
In bad or wintry weather, ensure that
the sensors are not covered with
mud, frost or snow. When reverse
gear is engaged, an audible signal
(long bleep) indicates that the
sensors may be dirty. The proximity information is given
by:
- an audible signal, which becomes
more rapid as the vehicle
approaches the obstacle,
- a graphic on the multifunction display, with blocks which become
progressively closer to the vehicle.
Depending on the multifunction
display, the audible signal is
transmitted by a buzzer or by the rear
speakers which transmit:
- on the right if an obstacle is detected on the right,
- on the left if an obstacle is detected on the left,
- on the right and on the left if an obstacle is detected in the centre.
When the distance between the
rear of the vehicle and the obstacle
is less than approximately thirty
centimetres, the audible signal
becomes continuous and the
"Danger" symbol appears depending
on the multifunction display.
Change to neutral, the system is
again inactive.
If there is an operating
fault, when reverse gear is
engaged, the service warning
light comes on, accompanied
by an audible signal (short bleep)
and a message on the multifunction
display.
Contact a PEUGEOT dealer.
Activation/Deactivation
Activation
The system is activated as soon as
reverse gear is engaged.
This is accompanied by an audible
signal and displaying of the vehicle,
depending on the multifunction
display. The system can be activated
or deactivated from the
multifunction display
c o n i g u r a t i o n m e n u .
The activation and deacti-
vation of the system are memorised
when the engine is switched off.
Switching the system off
Page 127 of 212
CHECKS
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r i l l p a s t t h i s m a r k .
B = minimum
Oil change
According to the information given in
the servicing booklet.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Note: the coolant does not need to
be changed.
Dipstick
Cooling system
U s e t h e l u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. This fan can oper-
ate with the ignition off.
I n t h e c a s e o f v e h i c l e s i t t e d w i t h
a p a r t i c l e e m i s s i o n i l t e r , t h e f a n
can operate after the vehicle has
s t o p p e d , e v e n w h e n t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level.
Windscreen and headlamp
w a s h l e v e l
Diesel additive level (Diesel
w i t h p a r t i c l e e m i s s i o n f i l t e r )
If the service warning light comes on,
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
Brake fluid level
* According to engine.
Oil level
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited.
The level should always be
above the MIN mark and
close to the MAX mark.
P o w e r s t e e r i n g r e s e r v o i r
Remove the style trim * (see §
"Changing a bulb - Front lights").
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT.
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick. Replacement must be car-
ried out according to the
manufacturer’s servicing
schedule.
U s e l u i d s r e c o m m e n d e d b y
t h e m a n u f a c t u r e r , w h i c h f u l i l D O T 4
standards.
Page 138 of 212
10PRACTICAL INFORMATION
124
Front lights
In the engine compartment, on the
right-hand side, remove the style
trim * :
- press the centre of each plastic stud A ,
- remove each plastic stud,
- remove the style trim.
W h e n y o u h a v e i n i s h e d , d o n o t
forget to put everything back in place
correctly:
- position the style trim * ,
- r e i t e a c h p l a s t i c s t u d A by
pressing on it. Handle the bulbs with a dry
cloth.
T h e h e a d l a m p s a r e i t t e d
with polycarbonate glass with
a protective coating. D o n o t c l e a n
t h e m w i t h a d r y o r a b r a s i v e c l o t h ,
n o r w i t h a d e t e r g e n t o r s o l v e n t
p r o d u c t .
Use a sponge and soapy water.
1 . D i p p e d b e a m h e a d l a m p s
( H 1 - 5 5 W o r x e n o n b u l b ) .
W A R N I N G : R I S K O F E L E C T R O -
C U T I O N
Xenon bulbs must be changed by a
PEUGEOT dealer.
2. M a i n b e a m h e a d l a m p s ( H 7 - 5 5 W ) .
Remove the protective cover
corresponding to the faulty bulb.
Disconnect the connector.
Press the end of each securing
clip. Change the bulb.
W h e n i t t i n g t h e n e w b u l b , e n s u r e that the direction notches are
positioned correctly and the
s e c u r i n g c l i p s a r e i x e d p r o p e r l y .
Reconnect the connector.
R e i t t h e p r o t e c t i v e c o v e r .
C H A N G I N G A B U L B
* According to engine.
Page 139 of 212
10PRACTICAL INFORMATION
125
I n t e g r a t e d d i r e c t i o n i n d i c a t o r s i d e
repeaters.
Push the repeater forwards and
release it.
Remove the repeater and change
it.
These can be obtained from a
PEUGEOT dealer.
Amber coloured bulbs, such
as the direction indicators,
must be replaced with bulbs
o f i d e n t i c a l s p e c i i c a t i o n a n d
colour.
3 . S i d e l i g h t s ( W 5 W ) .
Remove the protective cover
corresponding to the faulty bulb.
Disconnect the connector.
Remove the bulb and change it.
4 . D i r e c t i o n i n d i c a t o r s (PY 21 W amber).
Turn the bulb holder a quarter of
a turn and remove it.
Change the bulb.
Note
: in certain climatic conditions
(low temperature, humidity), c o n d e n -
s a t i o n i n s i d e t h e h e a d l a m p g l a s s i s
normal ; it disappears a few minutes
after the lights are switched on.
5 . F o g l a m p s ( H 1 1 - 5 5 W ) .
Contact a PEUGEOT dealer to have
these bulbs changed.
Page 140 of 212
10PRACTICAL INFORMATION
126
1. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
2. R e v e r s i n g l i g h t s ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
3. Brake lights (P 21 W).
4. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
Using a 10 mm box spanner,
u n s c r e w t h e 2 i x i n g n u t s 1 .
Release the lamp unit by pushing
it outwards.
Squeeze the two tabs 2 to release
the bulb holder.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
lamp unit seal has been put back
in place correctly.
These 6 bulbs are changed from
inside the boot:
Move aside the boot trim to
access the bulb holder,
Press the two tabs and remove
the bulb holder,
Change the faulty bulb.
W h e n r e i t t i n g , t a k e c a r e t o p a s s t h e
trim under the seal.
Rear lights (saloon) T h i r d b r a k e l i g h t ( s a l o o n )
(4 W 5 W bulbs)
Page 141 of 212
10PRACTICAL INFORMATION
127
Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direction
of engagement.
Insert a screwdriver into the two
outer holes B to press on the two
tabs C .
Push the light unit outwards while
maintaining the pressure on the
tabs.
Pull the light unit outwards while
tilting it.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
light unit tabs are engaged
correctly and that the tailgate
upper trim has been put back in
place correctly.
1. Brake lights (P 21 W).
2. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
3. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
4. R e v e r s i n g l i g h t ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
These 6 bulbs are changed by
removing the light:
Remove the corresponding boot
side trim to access the light,
R e m o v e t h e l i g h t i x i n g n u t i n s i d e
the boot,
R e m o v e t h e l i g h t i x i n g n u t o u t -
side the boot,
Remove the light,
Unclip the harness,
Remove the bulb holder pressing
on the tabs A ,
Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e i t t i n g , t a k e c a r e t o p o s i t i o n
the bulb holder and the light
correctly.
Number plate lights
(W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.
Rear lights (estate) T h i r d b r a k e l i g h t ( e s t a t e )
(4 W 5 W bulbs)
Page 144 of 212
10PRACTICAL INFORMATION
129
Fuse N° Rating
Functions
F6 30 A Rear electric windows.
F7 5 A Front and rear courtesy lights, map reading lights, glove bo x lighting.
F8 20 A Audio equipment, audio/telephone, multifunction display
, alarm siren, alarm unit, trailer fuse
box, driving school module, steering wheel controls supply.
F9 30 A 12 V front socket, 12 V rear socket.
F10 15 A A u t o m a t i c g e a r b o x c o n t r o l u n i t , t y r e u n d e r - i n l a t i o n c o n t r o l u n i t , S T O P s w i t c h .
F11 15 A D i a g n o s t i c s o c k e t , p a r t i c l e e m i s s i o n i l t e r u n i t , l o w c u r r e n t i g n i t i o n s w i t c h .
F12 15 A Driving school module, rear parking assistance.
F13 5 A Engine fuse box, rain and brightness sensor.
F14 15 A Trailer fuse box, instrument panel, air bags and pre-tensioners
unit, automatic air conditioning,
hands-free kit.
F15 30 A Locking and deadlocking.
F16 - PARC shunt.
F17 40 A Heated rear screen.
Page 149 of 212
10PRACTICAL INFORMATION
134
E C O N O M Y M O D E F U N C T I O N
After the engine has stopped, certain
functions (windscreen wiper, electric
windows, sunroof, courtesy lights,
audio equipment, telephone, dipped
headlamps, etc.) can only be used for
a combined duration of approximately
thirty minutes, to prevent discharging
the battery.
Once the thirty minutes are over, a
switching to economy mode message
appears on the multi-function display
and the active functions are put on
standby.
These functions are reactivated
automatically next time the vehicle is
driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then
be double the duration for which the
engine is left running. However, this
p e r i o d w i l l a l w a y s b e b e t w e e n i v e
and thirty minutes. A l a t b a t t e r y p r e v e n t s t h e
engine from starting.
L O A D R E D U C T I O N
F U N C T I O N
When driving, certain functions (air
conditioning, heated rear screen,
heating system for passenger
compartment of diesel vehicles, etc.)
may be switched off temporarily,
depending on the level of battery
charge.
Reactivation of these functions is
automatic, once the battery charge is
s u f i c i e n t .
Note: at the risk of discharging the
battery, the functions that have been
switched off may be reactivated
manually.
Note: if the telephone is
being used when economy
mode starts, it will still be
p o s s i b l e t o i n i s h t h e c a l l .