ignition Peugeot 308 2016 Owner's Guide

56
308_en_Chap02_ouvertures_ed02-2015
Complete unlocking
"Keyless entry and Starting" on your person
System for unlocking, locking and starting the
vehicle while keeping the electronic key on your
person.
F
Wi

th the electronic key on your person and
in the recognition zone A , pass your hand
behind one of the front door handles to
unlock the vehicle, then pull on the handle
to open the door.
the c

entral locking does not take place:
-
if t

he ignition is on,
-
if o

ne of the doors or the boot is still
open,
-
if t

he key for the Keyless
ent
ry and
Starting system has been left inside
the vehicle.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock itself
again automatically after about thirty
seconds unless a door is opened.
And if your vehicle has an alarm, this is
not reactivated.
the f

olding and unfolding of the door
mirrors by the remote control can be
deactivated by a P
eu

ge
Ot d
ealer or a
qualified workshop.Selective unlocking
When selective unlocking of the driver's door is
activated.
F
Wi

th the electronic key in the driver's door
zone, pass your hand behind the driver's
door handle to unlock just the driver's door,
then pull on the door handle to open the
d o o r.
F
Wi

th the electronic key in the passenger's
door zone, pass your hand behind the
passenger's door handle to unlock the
whole vehicle, then pull on the door handle
to open the door.
By default, complete unlocking is activated.
thi

s setting is done in the "Driving
assistance" menu, then "Vehicle settings"
and "Vehicle access" .
use t

his button for access to
additional information.
unl

ocking is confirmed by rapid
flashing of the direction indicators for a
few
se

conds.
Depending on version, the door mirrors
unfold, the alarm is deactivated.
Access

61
308_en_Chap02_ouvertures_ed02-2015
Back-up key
Unlocking/locking using the
integral key with Keyless
Entry and Starting
the integral key is used to lock and unlock the
v ehicle when the electronic key cannot operate:
-
ce

ll battery flat, vehicle battery discharged
or disconnected, ...
-
ve

hicle located in an area with strong
electromagnetic signals.
F
Ma

intain a pull on button 1 , to extract the
integral key 2 .
Locking the driver's door
F Insert the integral key in the door lock, then
t
urn it to the rear.
Unlocking the driver's door
F Insert the integral key in the door lock, then
turn it to the front.
Locking the passenger doors
F Open the doors.
F Fo r the rear doors, check that the child lock
is not on.
F
In

sert the integral key in the latch located
on the edge of the door and turn it an
eighth of a turn to the right for the right
hand door, and to the the left for the left
hand door.
F
Cl

ose the doors and check that the vehicle
has locked correctly from the outside.
If the alarm is activated, the audible
signal on opening a door with the key
(integral with the remote control) will
stop when the ignition is switched on.
Unlocking the passenger doors
F Pull the interior door opening control.
F
or more information on the child lock,
refer to the corresponding section.
2
Access

62
308_en_Chap02_ouvertures_ed02-2015
Changing the cell battery
Battery ref.: CR2032 / 3 volts.this replacement battery is available from a
P
eu

ge
Ot d
ealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is
needed.
F


u
nc
lip the cover using a small screwdriver
at the cutout.
F
Li

ft off the cover.
F
Re

move the flat battery from its location.
F
Fi

t the new battery into its location
observing the original direction of fitment.
F
Cl

ip the cover onto the casing.Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
tak

e them to an approved collection
point. Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F
Pl

ace the mechanical key (integral with the
remote control) in the lock to unlock your
vehicle.
F
Re

move the mat under 12 V socket.
F
Pl

ace the electronic key in the housing
provided.
F
Sw

itch on the ignition by pressing S
tARt/
StO P.the

electronic key is fully operational again.
Remote control problem -
reinitialisation
If the problem persists, contact a PeugeOt d ealer
or a qualified workshop as soon as possible.
Access

63
308_en_Chap02_ouvertures_ed02-2015
Lost keys, remote control, electronic key
Visit a PeugeOt dealer with the vehicle's registration certificate, your personal identification documents and if possible, the label bearing the
key code.
the Peu

ge
Ot d
ealer will be able to retrieve the key code and the transponder code required to order a new key
Remote control
the high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the
v ehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it from
working and the remote control would have to be reinitialised.
the r

emote control does not operate when the key is in the ignition, even when the ignition is switched off.
Locking the vehicle
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
As a safety precaution (with children on board), remove the key from the ignition or take the electronic key when you leave the vehicle, even for
a short time.
Electrical interference
the Keyless ent ry and Starting electronic key may not operate if close to certain electronic devices: telephone, laptop computer, strong
magnetic fields, ...
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
Don't forget to turn the steering to engage the steering lock.
When purchasing a second-hand vehicle
Have the key codes memorised by a Peu geOt d ealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
2
Access

66
308_en_Chap02_ouvertures_ed02-2015
Deactivation
F Lock the vehicle using the "Keyless entry
and starting" system. F
Pr

ess this unlocking button on
the remote control.
or
F unl ock the vehicle using the "Keyless ent ry
and Starting" system.
If the vehicle self-locks automatically
(occurs after 30 seconds if a door or
the boot is not opened), the monitoring
system is not reactivated automatically.
to re

activate the system, it is necessary
to unlock and then lock the vehicle
again, using the remote control or the
"Keyless
ent

ry and starting" system.
the m
onitoring system is deactivated: the
indicator lamp in the button is off and the
direction indicators flash for about 2 seconds.
Total protection
Activation
F Lock the vehicle using the
r emote control.
or
the m

onitoring system is active: the indicator
lamp in the button flashes once per second and
the the direction indicators come on for about
2 seconds.
After an instruction to lock the vehicle using
the remote control or the Keyless
ent

ry
and Starting system, the exterior perimeter
monitoring is activated after a delay of
5
s

econds, the interior volumetric monitoring
after 45 seconds.
If an opening (door, boot, bonnet...) is not
closed fully, the vehicle is not locked but
monitoring will be activated after a delay of
45
se

conds.
F
Switch off the ignition and get out of the vehicle.
Protection - exterior
perimeter monitoring only
Deactivate the interior volumetric monitoring
(and tilt monitoring if your vehicle has it) to
avoid unwanted triggering of the alarm in
certain cases such as:
-
oc

cupant(s) present in the vehicle,
-
le

aving a window partially open,
-
was

hing your vehicle,
-
chan

ging a wheel,
-
to

wing your vehicle,
-
tr

ansport on a ferry.
Access

67
308_en_Chap02_ouvertures_ed02-2015
Volumetric monitoring
Deactivationthe tilt alarm is deactivated as well, if your
vehicle has it.
F
Sw

itch of the ignition and within
ten seconds press this button
until its indicator lamp is on fixed.
F


g
et o
ut of the vehicle. Reactivationthe t
ilt alarm is reactivated as well, if your
vehicle has it.
the i

ndicator lamp in the button goes off.
F
Im

mediately lock the vehicle
using the remote control or the
"Keyless
ent

ry and Starting"
system.
Only the exterior perimeter protection system is
active: the indicator lamp in the button flashes
once per second.
to be e

ffective, this deactivation must be done
every time the ignition is switched off. F
Dea

ctivate the exterior perimeter
monitoring by unlocking the
vehicle using the remote control
or the Keyless
ent

ry and starting
system.
F
Re

activate the full alarm system
by locking the vehicle using the
remote control or the "Keyless
ent

ry and starting" system.
the i

ndicator lamp in the button flashes once
per second again.
Triggering of the alarm
this is indicated by sounding of the siren
a nd flashing of the direction indicators for
thirty
s

econds.
the m

onitoring functions remain active until
the alarm has been triggered eleven times in
succession.
When the vehicle is unlocked using
the remote control or the Keyless
ent

ry and starting system, rapid
flashing of the indicator lamp in the
button informs you that the alarm was
triggered during your absence.
When the ignition is switched on, this
flashing stops immediately.
2
Access

68
308_en_Chap02_ouvertures_ed02-2015
Failure of the remote control
to deactivate the monitoring functions:
F unl ock the vehicle using the key (integral
with the remote control) in the driver's door
lock.
F
Op

en the door; the alarm is triggered.
F
Sw

itch on the ignition; the alarm stops.
the
i

ndicator lamp in the button goes off.
Locking the vehicle without
activating the alarm
F Lock or deadlock the vehicle using the key
( integral with the remote control) in the
driver's door lock.
Operating fault
When the ignition is switched on,
fixed illumination of the indicator
lamp in the button indicates a fault in
the system.
Have it checked by a P
eu

ge
Ot
d

ealer or a qualified workshop.
Automatic activation
this function is either not available, an option
o r is standard.
2 minutes after the last door or the boot is
closed, the system is activated automatically.
F


t
o av
oid triggering the alarm on entering
the vehicle, first press the unlocking button
on the remote control or unlock the vehicle
using the Keyless
ent

ry and starting
system.
Access

69
308_en_Chap02_ouvertures_ed02-2015
electric windows
1. Front left.
2. Fr ont right
3.
Re

ar right.
4.
Re

ar left.
5.
Dea

ctivating the rear electric window
switches.
Manual operation
to open or close the window, press or pull
t he switch fully: the window opens or closes
completely when the switch is released.
Pressing the switch again stops the movement
of the window.
Safety anti-pinch
(depending on version)
Automatic one-touch operation
(depending on version)
to open or close the window, press or pull the
s witch gently. the w indow stops as soon as the
switch is released. When the window rises and meets an obstacle,
it stops and immediately partially lowers again.
Maintaining the locking action (on the
key or the remote control) closes the
windows automatically.
the e
lectric window switches remain
operational for approximately one minute after
the key has been removed.
Once this time has elapsed, the electric
windows will not operate.
to re

activate them,
switch the ignition on again. In the event of unwanted opening of the window
when closing automatically, press the switch
until the window opens completely, then pull
the switch immediately until the window closes.
Continue to hold the switch for approximately
one second after the window has closed.
the s

afety anti-pinch function is not active
during this operation.
2
Access

74
308_en_Chap03_ergonomie-et-confort_ed02-2015
System which registers the electrical settings
of the driver's seat and the door mirrors.
You can store and recall two positions using
the buttons on the side of the driver's seat.
Storing driving positions
Storing a position
Using buttons M / 1 / 2
F Switch on the ignition.
F Ad just your seat and the door mirrors.
F
Pr

ess button M , then press button 1 or 2
within four seconds.
An audible signal indicates that the position has
been stored.
Storing a new position cancels the previous
position.
Recalling a stored position
Ignition on or engine running
F Press button 1 or 2 to recall the
c orresponding position.
An audible signal confirms that adjustment is
complete.
You can interrupt the current movement by
pressing button M , 1 or 2 or by using one of the
seat controls.
A stored position cannot be recalled while
driving.
Recalling stored positions is deactivated
45
s

econds after switching off the ignition.
ease of use and comfort

96
308_en_Chap03_ergonomie-et-confort_ed02-2015
Dual-zone digital air conditioning (touch screen)
this air conditioning system operates with the engine running, but the ventilation and its controls
a re available with the ignition on.
Operation of the air conditioning and regulation of temperature, air flow and air distribution in the
passenger compartment are automatic according to the temperature in the passenger compartment
and the temperature setting.Temperature adjustment
the driver and front passenger can each set
t he temperature.
F
Pr

ess one of these buttons to
increase the value.
the v

alue indicated corresponds to a level of
comfort and not to a temperature in degrees
Centigrade or Fahrenheit (depending on the
units chosen).
A setting around 21 provides an optimum level
of comfort. Depending on your requirements, a
setting between 18 and 24 is normal.
In addition, it is recommended that you avoid a
difference between the left and right setting of
more than 3.
Press the button for the "
Air conditioning" menu to display the controls for the air
conditioning system. F
Pr

ess one of these buttons to
decrease the value.
ease of use and comfort