headlamp Peugeot 308 SW BL 2008 Owner's Manual

!
INSTRUMENTS and CONTROLS
The warning lights may come on
continuously or fl ash.
Certain warning lights may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situ-
ation is normal or whether a fault
has occurred.
Indicator and warning lights
Visual indicators informing the driver
that a system is in operation (operation
or deactivation indicator lights) or of the
occurrence of a fault (warning light).
Associated warnings
The switching on of certain warning
lights may be accompanied by an audi-
ble signal and a message on the multi-
function display.
Operation indicator lights
If one of the following indicator lights comes
on, this confi rms that the corresponding
system has come into operation.
Left-hand direction indicator.
Handbrake applied.
Right-hand direction
indicator.
Main beam headlamps.
Dipped headlamps.
Diesel engine pre-heating.
Wait until this is switched off
before operating the starter.
Front fog lamps.
Rear fog lamp.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle’s ignition is
switched on.
When the engine is started, these warning
lights should switch off.
If they remain on, before moving off,
consult the warning light concerned.
Common operation indicator lights

25
INSTRUMENTS and CONTROLS
Foot on brake.
Press the brake pedal to start
the engine with the 6-speed pi-
loted manual gearbox or auto-
matic gearbox.
Specifi c operation indicator lights
The other indicator lights appear on the
large display, located in the centre of
the instrument panel.
Automatic locking.
If this is displayed, it indicates
that you have activated the au-
tomatic locking of the doors and
boot while driving. Speed limiter.
If this is displayed, it indicates
that you have activated the
speed limiter mode.
If this is displayed, it indi-
cates that you can set the
speed limiter speed value to
be stored.
Cruise control.
If this is displayed, it indicates
that you have activated the
cruise control mode.
If this is displayed it indi-
cates that you can set the
cruise control speed value
to be stored.
Automatic gearbox. This display indicates the po-
sition that you have selected
on the gear selection gate
(R, N, A or M).
Automatic wiping.
If this is displayed, it indicates
that you have activated the auto-
matic windscreen wiping.
Automatic lighting.
If this is displayed, it indicates
that you have activated the
automatic switching on of the
headlamps.
This display indicates the gear
engaged in automatic or man-
ual operating mode (1 to 6).
This display indicates the op-
erating mode selected (auto-
matic or sport).
This display indicates the gear
engaged in the automatic or
manual operation programme.
This display indicates the op-
erating programme selected
(automatic, sport, snow or
manual).
6-speed piloted manual gearbox.
This display indicates the posi-
tion that you have selected on
the gear selection gate (P, R, N
or D).

26
INSTRUMENTS and CONTROLS
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the corre-
sponding system has been switched off
intentionally.

Passenger’s air bag system
deactivation.
The passenger’s air bag system
is put into service automatically
when the vehicle is started.
A specifi c control, located on the pas-
senger’s side of the fascia, permits
deactivation of the system. This is
confi rmed by continuous lighting of this
warning light on the instrument panel or
on the seat belt and passenger’s front
air bag warning lights display. Dynamic stability control
(ESP/ASR) deactivation.
The ESP/ASR system is put
into service automatically when
the vehicle is started.
A specifi c button, located in the centre
of the fascia, permits deactivation of the
system. This is confi rmed by continu-
ous lighting of this warning light and of
the indicator light on the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically.
Common deactivation warning
lights Specifi c deactivation warning lights
Automatic locking.
If this is displayed, it indicates
that you have deactivated the
automatic locking of the doors
and boot while driving. Automatic wiping.
If this is displayed, it indicates
that you have deactivated the
automatic windscreen wiping.
The other warning lights appear on the
large display, located in the centre of
the instrument panel. Speed limiter.
If this is displayed, it indicates
that you have deactivated the
speed limiter.
Cruise control.
If this is displayed, it indicates
that you have deactivated the
cruise control.
Automatic lighting.
If this is displayed, it indicates
that you have deactivated the
automatic switching on of the
headlamps.

i
!
29
INSTRUMENTS and CONTROLS
The displaying of certain warning
lights may be accompanied by an
audible signal and a message on
the multifunction display.
Specifi c warning lights
The other warning lights appear on the
large display, located in the centre of
the instrument panel.
Depending on the seriousness of the
fault, they may be displayed in orange
or red.
Certain warning lights may be
linked with those of the instrument
panel.
If they are linked with the
STOP
warning light, stop the vehicle imme-
diately and as safely as possible.
Directional headlamps.
If this fl ashes, it indicates the
occurrence of a fault in the di-
rectional headlamps system. Engine oil pressure.
If this is displayed, it indicates
the occurrence of a fault in the
engine lubrication circuit. Stop
the vehicle immediately and as safely
as possible.
Service.
If this is displayed, it indicates
the occurrence of a fault in one
of the following: Engine autodiagnostics
system.
If this is displayed, it indicates
the occurrence of a fault in the
engine management system. Engine oil level.
If this is displayed, it indicates
an insuffi cient level of oil in the
engine. Stop the vehicle imme-
diately and as safely as possible.
Coolant temperature.
If this is displayed, it indicates
that the temperature in the
cooling system is too high. Stop
the vehicle immediately and as safely
as possible.
Coolant level.
If this is displayed, it indicates
an insuffi cient level of coolant
in the circuit. Stop the vehicle
immediately and as safely as
possible.
Battery charge.
If this is displayed, it indicates
the occurrence of a fault in the
battery charging circuit (dirty or
loose terminals, slack or cut alternator
belt, ...).
- the engine management system,
- the emission control system,
- the lane departure warning system.

INSTRUMENTS and CONTROLS Water in diesel.
If this is displayed, it indicates
the presence of water in the
diesel fi lter.
There is a risk of damage to the injection
system on Diesel engines.
Automatic headlamp
adjustment.
If this is displayed, it indicates the
occurrence of a fault in the auto-
matic headlamp adjustment.
Particle emission fi lter
(Diesel).
If this is displayed, linked with
the service warning light, it indi-
cates the start of saturation of the par-
ticle emission fi lter or a low diesel addi-
tive reservoir level.
As soon as traffi c conditions permit, re-
generate the fi lter by driving at a speed
of at least 40 mph (60 km/h) until the
service warning light is switched off.
If the service warning light is still displayed,
the additive level is low. Have it topped up
by a PEUGEOT dealer without delay.
Defl ated wheel.
If this is displayed, it indicates
an insuffi cient pressure in one
or more wheels.
Check the pressure of the tyres as soon
as possible. Punctured wheel.
If this is displayed, it indicates
that one or more wheels are
punctured. Stop the vehicle
immediately and as safely as
possible.
Change the damaged wheel and have it
repaired by a PEUGEOT dealer.
Tyre under-infl ation
detection.
If this is displayed, it indicates
the occurrence of a fault on one
of the sensors or in the tyre under-infl a-
tion detection system.
It may also indicate the absence of a
sensor when the spare wheel, which
does not have a sensor, is fi tted in place
of a punctured wheel.
Automatic switching on of
the lights.
If this comes on, it indicates
the occurrence of a fault in the
automatic switching on of the
lights.
Use the other positions of the lights
stalk.
Visual and/or audible
parking assistance.
If this comes on, in forward and/
or reverse gear, it indicates a
fault in the parking assistance
system.
6-speed piloted manual
gearbox or automatic
gearbox.
If this is displayed, it indicates
the occurrence of a fault in the 6-speed
piloted manual gearbox or automatic
gearbox. The gearbox will then operate in
down-grade mode, locked on 3rd gear.
Invalid value.
If this is displayed, it indicates
the occurrence of a fault in the
programme of the 6-speed pi-
loted manual gearbox or auto-
matic gearbox.
Position P or N.
If this is displayed, it indicates
that the gear lever must be
placed in position
P or N in or-
der to start the engine.

41
MULTIFUNCTION DISPLAYS
MONOCHROME SCREEN C AND COLOUR SCREEN C General menu
Displays on the screen
This displays the following information:
- the time,
- the date,
- the outside temperature * (this fl ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the audio sources (radio, CD, ...),
- the trip computer (refer to the end of the section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Automatic switching
on of the headlamps activated") may ap-
pear temporarily. These can be cleared
by pressing the "ESC" button. "Audio functions" menu Controls
From the RD4 audio equipment control
panel, you can:

 press the "MENU" button to gain
access to the general menu ,

 press the " " or " " buttons to
scroll through the items on the
screen,

 press the "MODE" button to change
the permanent application (trip
computer, audio source, ...),

 press the " " or " " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress.
 Press the "MENU" button to gain
access to the general menu :
- audio functions,
- vehicle diagnostics,
- personalisation-confi guration,
- telephone (hands-free kit).

 Press the " " or " " buttons to
select the menu required, then
confi rm by pressing the "OK"
button.
* With air conditioning only.
With the RD4 audio equipment switched
on, once this menu has been select-
ed you can activate or deactivate the
functions linked with use of the radio
(RDS, REG, RadioText), the CD or the
CD changer (introscan, shuffl e, CD
repeat).
For further details concerning the "Audio
functions" application, refer to the RD4
part of the "Audio and Telematics"
section.

46
MULTIFUNCTION DISPLAYS
Defi ne the vehicle parameters
Once the "Defi ne the vehicle parame-
ters" menu has been selected, you can
activate or deactivate certain driving
and comfort equipment:
- selective unlocking (refer to the "Ac-cess" section),
- wiper linked with reverse gear (refer to the "Visibility" section),
- follow-me-home and welcome light- ing (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section). Example: setting the duration of the follow-
me-home lighting

 Turn the navigator to select the

"Lighting confi guration" menu,
then press the navigator to confi rm.

 Select the line "Duration of follow-
me-home lighting" then confi rm.
"Configuration" menu Once this menu has been selected,
you can gain access to the following
functions:

 Select the duration then press the
navigator.

 Turn the navigator to set the value
required (15, 30 or 60 seconds),
then press the navigator.

 Select the "OK" box, then confi rm.

 Press the "MENU" button on the
RT4 GPS audio/telephone to gain
access to the general menu .

 Turn the navigator to select the

"Confi guration" menu, then press
the navigator to confi rm.

77
ACCESS
Locating your vehicle

 Press the closed padlock to locate
your locked vehicle in a car park.
This is indicated by lighting of the cour-
tesy lights and dipped headlamps and
fl ashing of the direction indicators for a
few seconds. Lost keys
Visit a PEUGEOT dealer with the vehi-
cle’s V5 registration certifi cate and your
personal identifi cation documents.
Your PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code to order a replacement key.
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.
Anti-theft protection
In the event of a malfunction,
you are informed by lighting of
this warning light, an audible
signal and a message on the
multifunction display.
In this case, your vehicle does not start;
contact a PEUGEOT dealer as soon as
possible.
Folding the key

 First press button A to fold the key.

77
ACCESS
Locating your vehicle

 Press the closed padlock to locate
your locked vehicle in a car park.
This is indicated by lighting of the cour-
tesy lights and dipped headlamps and
fl ashing of the direction indicators for a
few seconds. Lost keys
Visit a PEUGEOT dealer with the vehi-
cle’s V5 registration certifi cate and your
personal identifi cation documents.
Your PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code to order a replacement key.
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.
Anti-theft protection
In the event of a malfunction,
you are informed by lighting of
this warning light, an audible
signal and a message on the
multifunction display.
In this case, your vehicle does not start;
contact a PEUGEOT dealer as soon as
possible.
Folding the key

 First press button A to fold the key.

90
VISIBILITY
LIGHTING CONTROLS
System for selection and control of the
various front and rear lights providing
the vehicle’s lighting.
Main lighting
The various front and rear lights of the
vehicle are designed to adapt the driv-
er’s visibility progressively in relation to
the climatic conditions:
- side lights, to be seen,
- dipped headlamps to see without dazzling other drivers,
- main beam headlamps to see clearly when the road is clear,
- directional headlamps for improved visibility when cornering.
Additional lighting
Other lights are installed to fulfi l the require-
ments of particular driving conditions:
- rear fog lamps to be seen from a distance,
- front fog lamps for even better visibility,
- daytime lights to be seen during the day.
Programming
Various automatic lighting control
modes are also available according to
the following options:
- follow-me-home lighting,
- automatic lighting,
- directional lighting Model without AUTO lighting
Model with AUTO lighting automatic switching on of
the lights,
Manual controls
The lighting commands are issued di-
rectly by the driver by means of the ring

A and the lever B .

A. main lighting mode selection ring,
with:
lights off,
side lights only,

B. lever for inversion of the lights by
pulling: dipped headlamps/main beam
headlamps.
In the lights off and side lights modes,
the driver can switch on the main beam
headlamps directly ("headlamp fl ash")
for as long as he pulls the lever. dipped headlamps or main
beam headlamps.
Displays
Lighting of the corresponding indicator
light on the instrument panel confi rms
the selective switching on of the lighting
selected.