ECU Peugeot 308 SW BL 2008 Owner's Manual

i!
63
COMFORT
Storing driving positions
System which takes into account the
electrical settings of the driver’s seat
and exterior mirrors. It enables you to
store up to two positions using the but-
tons on the side of the driver’s seat and
two further driving positions using the
two remote control keys.
Recalling a stored position
When the vehicle is unlocked, the driv-
er’s seat and the exterior mirrors return
to the position stored by the remote
control key.
Storing a position Storing a new position cancels the
previous position.
When the ignition is off, after a few
consecutive position recalls, the
function will be deactivated until
the engine is started, to prevent
discharging of the battery.
Using the remote control keys
When the vehicle is locked, the remote
control key stores the position of the
driver’s seat and exterior mirrors.
Each remote control key can store one
specifi c setting.
Ignition on

 Briefl y press button 1 or 2 to recall
the corresponding position.
An audible signal is heard indicating the end of the adjustment. Vehicle moving

 Press and hold button 1 or 2 until
the audible signal is heard indicating
the end of the adjustment.
Using buttons M/1/2

 Switch on the ignition.

 Adjust your seat and your exterior
mirrors.

 Press button M , then press button 1
or 2 within four seconds.
An audible signal is heard indicating that the storing has been taken into
account.

!
64
COMFORT
REAR SEATS
Never drive with the head restraints
removed; they must be in place
and in the high position when pas-
sengers are seated in the rear.
Rear head restraints
These have a high position (comfort
and safety) and a low position (rear visi-
bility).
They can also be removed.
To remove a head restraint:

 pull the head restraint fully forwards
and upwards at the same time,

 then, press the lug A . Removing the seat cushion

 Move the corresponding front seat
forwards if necessary.

 Pull the handle 1 forwards to raise
the seat cushion 2 .

 Tilt the seat cushion 2 fully against
the front seat.

 Remove the seat cushion 2 from its
fi xings by pulling upwards.
Refitting the seat cushion

 Position the seat cushion 2 vertically
in its fi xings.

 Fold down the seat cushion 2 .


Press on the seat cushion to secure it.
Bench seat the left-hand (2/3) or right-
hand (1/3) section of which can be folded
to adapt the boot load space.

!
i
65
COMFORT
Folding the seat
In order to fold a rear seat without any
risk of damage, always start with the
seat cushion, never with the seat
back :

 move the corresponding front seat
forwards if necessary,

 pull the handle 1 forwards to raise
the seat cushion 2 ,

 tilt the seat cushion 2 fully against
the front seat,
Returning the seat back to its
original position
When returning the rear seat back to its
original position:

 put the seat back 4 in the upright
position and secure it,

 fold the seat cushion 2 ,

 refi t the head restraints or put them
back in place.

 check that the seat belt is positioned
correctly on the side of the seat back,

 lower or remove the head restraints
if necessary,

 pull the control 3 forwards to release
the seat back 4 ,

 tilt the seat back 4 .
When returning the rear seat back
to its original position, take care not
to trap the seat belts and ensure
that their buckles are positioned
correctly. The seat cushion
2 can be removed
to increase the loading volume.

!
68
COMFORT
ADDITIONAL SEATS
Table position

 Place the head restraint in the low
position.

 Pull the strap A , located at the rear
left of the seat.

 Fold the seat back onto the seat
cushion. Folding
Once the seat has been placed in the
table position, carry out the following
operations:

 remove the load space screen
roller,

 raise the bar B , located at the rear of
the seat, to release the rear feet,

 raise the seat and secure it to the
head restraint rod of the 2nd row
seat, using the integrated retaining
strap C . Removal
Once the seat has been folded, carry
out the following operations:

 pull the red strap D to release the
front feet of the seat,

 lift the seat and carry it using the
carrying handle E ,

 put the anchorage covers back in
place to obtain a fl at boot fl oor.
Never use the adjustment and re-
taining straps to remove, install
or carry a seat; use the carrying
handle E provided for this purpose
(weight of the seat: approximately
15 kg).
In the 3rd row, these two seats are strictly
identical and are used for the occasional
transportation of additional passengers.
They can be placed in the table position,
folded or removed to obtain a variety of
loading confi gurations.

i
89
ACCESS
The key cannot be removed from
the lock until the cap is put back on
the tank.
FUEL TANK

Capacity of the tank: approximately
60 litres.
To fi ll the tank safely:

 it is essential that the engine is
switched off,

 open the fuel fi ller fl ap,

 insert the key in the cap, then turn it
to the left,
When fi lling is complete:

 put the cap back in place,

 turn the key to the right, then remove
it from the cap,

 close the fl ap.

 remove the cap and secure it on the
hook, located on the inside of the
fl ap,

 fi ll the tank, but do not continue
after the 3rd cut-off of the nozzle ;
this could cause malfunctions.
Low fuel level
Filling
A label affi xed to the inside of the fl ap
reminds you of the type of fuel to be
used according to your engine.
Operating fault
A fuel gauge malfunction is indicated by
the return of the fuel level indicator nee-
dle to zero.
Consult a PEUGEOT dealer. When the fuel tank minimum
level is reached, this warning
light comes on on the instru-
ment panel, accompanied by
an audible signal and a message on the
multifunction display.

You have enough fuel left to drive ap-
proximately 30 miles (50 km).
If you run out of fuel, refer to the "Practical
information" section also.

!
!
104
LAYOUT To avoid any risk of jamming of the
pedals:
- only use mats which are suited to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of another
MAT
Removable component which protects
the carpet against exterior dirt. Refitting
To refi t the mat on the driver’s side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured
correctly.
Fitting
When fi tting the mat for the fi rst time,
use only the fi xings provided in the wal-
let attached.
Removal
To remove the mat on the driver’s side:

 move the seat as far back as
possible,

 unclip the fi xings

 remove the mat.
STORAGE DRAWERS *
Opening


Raise the front of the drawer and pull it.
* Except on electric seat.
Do not place heavy objects in the
drawers.
Removal

 Bring the drawer to the end of its
travel.

 Press the ends of the slides.

 Raise the drawer and pull it fully.
Refitting

 Engage the drawer in its slides.

 At the end of its travel, press on the
top of the drawer to secure it.

i
107
LAYOUT
To remove the shelf:

 unhook the two cords,

 raise the shelf slightly, then remove it.
Rear shelf
When changing a wheel
An additional hook, under the shelf,
permits easy access to the spare
wheel by retaining the boot carpet
by means of its cord.
To remove the shelf:

 unhook the two cords,

 raise the shelf slightly, then remove it.
Shelf with integrated storage
compartment
This permits the storage of any object so
that it cannot be seen from the outside
and without hindering rearward visibility.
The hooks permit the securing of shop-
ping bags.
Hooks
There are several options for storing the
shelf:
- either upright behind the front seats,
- or upright behind the rear seats using one of the movable straps. There are several options for storing the
shelf:
- either upright behind the front
seats,
- or upright behind the rear seats using one of the movable straps.

 To open the cover, from inside
or outside, raise one of the two
handles.

 To close the cover, fi rst raise the
handle.

 To remove the cover, raise both
handles at the same time.

108
LAYOUT Luggage retaining net
Hooked onto the stowing rings, this en-
ables you to secure your luggage.

 Raise the boot carpet to gain access
to the storage box.
This has areas for storing a box of spare
bulbs, a fi rst aid kit, a puncture repair
kit, two warning triangles, ...
Storage box

 In order to connect a 12 V accessory
(max power: 100 Watts), remove
the cap and connect the appropriate
adaptor.

 Turn the key to the ignition position.
12 V accessories socket
There are three possible positions:
- fl at at the bottom of the boot,
- horizontal at the rear shelf,
- vertical at the back of the rear seats.
Movable straps
Hooked onto the stowing rings, they
permit securing of your luggage.

i
110
LAYOUT
Load space cover
This consists of four sections three of
which can be folded back on each other.
There are several options for storing the
load space cover:
- either folded back on itself near the rear seats (1),
- or folded back on itself and stored in a location provided under the rear
seats (2).
To fold it from the boot:

 unclip the load space cover from its
side supports,

 take hold of the load space cover by
its handle A ,

 fold it concertina-style to the rear
seats.
To unfold it from the boot:

 take hold of the load space cover by
its handle A ,

 unfold it to the boot pillars,

 clip the load space cover on its side
supports. Luggage retaining net
Hooked onto the stowing rings, this en-
ables you to secure your luggage to the
bottom of the boot.
Hooks
The hooks permit the securing of shop-
ping bags.
Maximum loads
7.5 kg, load space cover unfolded
with high load retaining net at row 2.

i
113
LAYOUT
Load space screen
To install the load space screen:

 position one of the ends of the roller
in its support,

 insert the second end in its support;
the catch locks automatically,

 unroll the load space screen to the
boot pillars,

 insert the load space screen guides
in the rails on the boot pillars.
To store the load space screen, place it
at the boot sill, roller uppermost and fl ap
facing inwards.
To remove the load space screen:

 remove the load space screen
guides from the rails on the boot
pillars,

 roll up the load space screen in its
roller,

 pull and support the catch at one of
the ends of the roller to release it,

 remove the roller from its support
from the released end, then from the
second. Luggage retaining net
Hooked onto the stowing rings on the
fl oor and/or on the load space screen
roller, this enables you to secure your
luggage.
You can access the boot by open-
ing the rear screen and raising the
load space screen fl ap.
The roller has two rings for fi xing
the luggage retaining net depend-
ing on its location.